1 - Characterization of TiB 2 reinforced aluminum matrix composite synthesized by in situ stir casting method https://jourcc.com/index.php/jourcc/article/view/jcc241 10.29252/jcc.2.4.1 1 In this study, TiB2 reinforced Al-matrix composite was fabricated by in situ stir casting route, and the effect of processing parameters was investigated. X-ray diffraction (XRD) and field emission scanning electron microscopy (FE-SEM) equipped with energy-dispersive X-ray spectroscopy (EDX) were used to study the composition and microstructure of the samples. Finally, to investigate the tribological and electrochemical behavior of the samples, wear tests (pin-on-disk) and potentiodynamic polarization tests (PDP) were used, respectively. Results showed that by increasing stirring time, both tribological and mechanical behavior of the samples improved. Also, it was found that by increasing the stirring speed of the melt to 180 rpm, the mechanical and tribological behavior of the samples improved, and by further increasing the stirring speed to 300 rpm, they were decreased. Consequently, samples containing lower than 7 wt. % TiB2 showed better metallurgical properties, due to lack of agglomeration. 0 - 163 170 - - Fereshteh Barragh Jam Department of Chemical Engineering, University of Maragheh Iran info@jourcc.com - - Hadi Bangi Houri Department of Materials and Metallurgical Engineering, Ferdowsi University of Mashhad Iran Pers73hadi@gmail.com - - Morteza Ferdosi Faculty of Materials and Metallurgical Engineering, Semnan University Iran info@jourcc.com In situ Composite TiB2 Wear resistance Stir casting [1] A.M. Davitoiu, E. Truta, A.M. Mitu, A.A. Bojescu, F. Grama, M. Ionica, The Role of Aluminum in the Symptomatology of Attention Deficit Hyperactivity Disorder Children, Res. and Sci. Today 1 (2018) 115. ##[2] C.C.T. Leussa, L. Libessart, C. Djelal, C.N. Djangang, A. Elimbi, Pozzolanic activity of kaolins containing aluminum hydroxide, Scientific Reports 10(1) (2020) 1-12. ##[3] A. Bigham, A.H. Aghajanian, M. Movahedi, M. Sattary, M. Rafienia, L. Tayebi, A 3D nanostructured calcium-aluminum-silicate scaffold with hierarchical meso-macroporosity for bone tissue regeneration: Fabrication, sintering behavior, surface modification and in vitro studies, Journal of the European Ceramic Society (2020). ##[4] L.S. Fard, N.S. Peighambardoust, H.W. Jang, A. Dehghan, N.N.K. Saligheh, M. Iranpour, M.I. Rajabi, The rechargeable aluminum-ion battery with different composite cathodes: A review, Journal of Composites and Compounds 2(4) (2020) 138-146. ##[5] D.-L. Vu, N. Kim, Y. Myung, M. Yang, J.-w. Lee, Aluminum phosphate as a bifunctional additive for improved cycling stability of Li-S batteries, Journal of Power Sources 459 (2020) 228068. ##[6] J.L. Domingo, J. Llobet, M. Gomez, J. Tomas, J. Corbella, Nutritional and toxicological effects of short-term ingestion of aluminum by the rat, Research communications in chemical pathology and pharmacology 56(3) (1987) 409. ##[7] V.T. Targhi, H. Omidvar, F. Sharifianjazi, A. Pakseresht, Hot corrosion behavior of aluminized and Si-modified aluminized coated IN-738LC produced by a novel hot-dip process, Surfaces and Interfaces 21 (2020) 100599. ##[8] M.G. Soni, S.M. White, W.G. Flamm, G.A. Burdock, Safety evaluation of dietary aluminum, Regulatory toxicology and pharmacology 33(1) (2001) 66-79. ##[9] E.H. Jazi, R. Esalmi-Farsani, G. Borhani, F.S. Jazi, Synthesis and Characterization of In Situ Al-Al13Fe4-Al2O3-TiB2 Nanocomposite Powder by Mechanical Alloying and Subsequent Heat Treatment, Synthesis and Reactivity in Inorganic, Metal-Organic, and Nano-Metal Chemistry 44(2) (2014) 177-184. ##[10] Y. Zhang, N. Ma, H. Wang, Y. Le, X. Li, Damping capacity of in situ TiB2 particulates reinforced aluminium composites with Ti addition, Materials and design 28(2) (2007) 628-632. ##[11] S. Jayalakshmi, S. Gupta, S. Sankaranarayanan, S. Sahu, M. Gupta, Structural and mechanical properties of Ni60Nb40 amorphous alloy particle reinforced Al-based composites produced by microwave-assisted rapid sintering, Materials Science and Engineering: A 581 (2013) 119-127. ##[12] S. Rahimi, F. SharifianJazi, A. Esmaeilkhanian, M. Moradi, A.H.S. Samghabadi, Effect of SiO2 content on Y-TZP/Al2O3 ceramic-nanocomposite properties as potential dental applications, Ceramics International (2020). ##[13] S.A. Sajjadi, H.R. Ezatpour, M. Torabi Parizi, Comparison of microstructure and mechanical properties of A356 aluminum alloy/Al2O3 composites fabricated by stir and compo-casting processes, Materials and Design 34 (2012) 106-111. ##[14] P. Poddar, V.C. Srivastava, P.K. De, K.L. Sahoo, Processing and mechanical properties of SiC reinforced cast magnesium matrix composites by stir casting process, Materials Science and Engineering: A 460-461 (2007) 357-364. ##[15] S. Gopalakrishnan, N. Murugan, Production and wear characterisation of AA 6061 matrix titanium carbide particulate reinforced composite by enhanced stir casting method, Composites Part B: Engineering 43(2) (2012) 302-308. ##[16] B. Leila, S. Mostafa, S. Arman, A review of carbon nanotube/TiO2 composite prepared via sol-gel method, Journal of Composites and Compounds 1(1) (2019). ##[17] S. Kumar, M. Chakraborty, V. Subramanya Sarma, B.S. Murty, Tensile and wear behaviour of in situ Al–7Si/TiB2 particulate composites, Wear 265(1) (2008) 134-142. ##[18] C.S. Ramesh, A. Ahamed, Friction and wear behaviour of cast Al 6063 based in situ metal matrix composites, Wear 271(9) (2011) 1928-1939. ##[19] M. Emamy, M. Mahta, J. Rasizadeh, Formation of TiB2 particles during dissolution of TiAl3 in Al–TiB2 metal matrix composite using an in situ technique, Composites Science and Technology 66(7) (2006) 1063-1066. ##[20] S. Lakshmi, L. Lu, M. Gupta, In situ preparation of TiB2 reinforced Al based composites, Journal of Materials Processing Technology 73(1) (1998) 160-166. ##[21] Q. Zhang, B.L. Xiao, W.G. Wang, Z.Y. Ma, Reactive mechanism and mechanical properties of in situ composites fabricated from an Al–TiB2 system by friction stir processing, Acta Materialia 60(20) (2012) 7090-7103. ##[22] D.G. Zhao, X.F. Liu, Y.C. Pan, X.F. Bian, X.J. Liu, Microstructure and mechanical properties of in situ synthesized (TiB2+Al2O3)/Al–Cu composites, Journal of Materials Processing Technology 189(1) (2007) 237-241. ##[23] A. Masoudian, A. Tahaei, A. Shakiba, F. Sharifianjazi, J.A. Mohandesi, Microstructure and mechanical properties of friction stir weld of dissimilar AZ31-O magnesium alloy to 6061-T6 aluminum alloy, Transactions of nonferrous metals society of China 24(5) (2014) 1317-1322. ##[24] H. Morteza Ferdosi, E. Sara, D. Alireza, Ni-Cu matrix composite reinforced with CNTs: preparation, characterization, wear and corrosion behavior, inhibitory effects, Journal of Composites and Compounds 2(4) (2020). ##[25] S. Suresh, N. Shenbag, V. Moorthi, Aluminium-Titanium Diboride (Al-TiB2) Metal Matrix Composites: Challenges and Opportunities, Procedia Engineering 38 (2012) 89-97. ##[26] A.C. Reddy, Investigation of the Clustering Behavior of Titanium Diboride Particles in TiB2/AA2024 Alloy Metal Matrix Composites, 4th International Conference on Composite Materials and Characterization, Hyderabad, India, 2003, pp. 216-220. ##[27] B. Basu, G. Raju, A. Suri, Processing and properties of monolithic TiB2 based materials, International materials reviews 51(6) (2006) 352-374. ##[28] A. Aliasghar, M. Mostafa, The Effect of Cu-substitution on the microstructure and magnetic properties of Fe-15%Ni alloy prepared by mechanical alloying, Journal of Composites and Compounds 1(1) (2019). ##[29] E. Sharifi Sedeh, S. Mirdamadi, F. Sharifianjazi, M. Tahriri, Synthesis and evaluation of mechanical and biological properties of scaffold prepared from Ti and Mg with different volume percent, Synthesis and Reactivity in Inorganic, Metal-Organic, and Nano-Metal Chemistry 45(7) (2015) 1087-1091. ##[30] F. Chen, Z. Chen, F. Mao, T. Wang, Z. Cao, TiB2 reinforced aluminum based in situ composites fabricated by stir casting, Materials Science and Engineering: A 625 (2015) 357-368. ##[31] Y. Pazhouhanfar, B. Eghbali, Microstructural characterization and mechanical properties of TiB2 reinforced Al6061 matrix composites produced using stir casting process, Materials Science and Engineering: A 710 (2018) 172-180. ##[32] A.C. Reddy, Fracture behaviour of brittle matrix and alumina trihydrate particulate composites, (2002). ##[33] Z. Sadeghian, M.H. Enayati, P. Beiss, In situ production of Al–TiB2 nanocomposite by double-step mechanical alloying, Journal of Materials Science 44(10) (2009) 2566-2572. ##[34] L. Lu, M.O. Lai, F.L. Chen, Al-4 wt% Cu Composite reinforced with in-situ TiB2 particles, Acta Materialia 45(10) (1997) 4297-4309. ##[35] H.B. Michael Rajan, S. Ramabalan, I. Dinaharan, S.J. Vijay, Synthesis and characterization of in situ formed titanium diboride particulate reinforced AA7075 aluminum alloy cast composites, Materials and Design 44 (2013) 438-445. ##[36] M. Huang, X. Li, H. Yi, N. Ma, H. Wang, Effect of in situ TiB2 particle reinforcement on the creep resistance of hypoeutectic Al–12Si alloy, Journal of alloys and compounds 389(1-2) (2005) 275-280. ##[37] P.L. Schaffer, L. Arnberg, A.K. Dahle, Segregation of particles and its influence on the morphology of the eutectic silicon phase in Al–7 wt.% Si alloys, Scripta materialia 54(4) (2006) 677-682. ##[38] J. Wood, P. Davies, J. Kellie, Properties of reactively cast aluminium–TiB2 alloys, Materials science and technology 9(10) (1993) 833-840. ##[39] M. Zhao, G. Wu, L. Jiang, Z. Dou, Friction and wear properties of TiB2P/Al composite, Composites Part A: Applied Science and Manufacturing 37(11) (2006) 1916-1921. ##[40] A.P. Rao, K. Das, B. Murty, M. Chakraborty, Effect of grain refinement on wear properties of Al and Al–7Si alloy, Wear 257(1-2) (2004) 148-153. ##[41] M. Behpour, S. Ghoreishi, M. Khayatkashani, N. Soltani, The effect of two oleo-gum resin exudate from Ferula assa-foetida and Dorema ammoniacum on mild steel corrosion in acidic media, Corrosion science 53(8) (2011) 2489-2501. ##[42] M.F. Heragh, S. Eskandarinezhad, A. Dehghan, Ni-Cu matrix composite reinforced with CNTs: preparation, characterization, wear and corrosion behavior, inhibitory effects, Journal of Composites and Compounds 2(4) (2020) 123-128. ##[43] M.F. Heragh, H. Tavakoli, Electrochemical properties of a new green corrosion inhibitor derived from Prosopis farcta for St37 steel in 1 M hydrochloric acid, Metals and Materials International (2019) 1-10. ##[44] A. Satapathy, G. Gunasekaran, S. Sahoo, K. Amit, P. Rodrigues, Corrosion inhibition by Justicia gendarussa plant extract in hydrochloric acid solution, Corrosion science 51(12) (2009) 2848-2856.

1 - ISynthesis and mechanical properties of Bi2O3-Al4Bi2O9 nanopowders https://jourcc.com/index.php/jourcc/article/view/jcc242 10.29252/jcc.2.4.2 1 As a result of great surface area and a great number of energetic sites, ceramic nanocomposites are being considered as good adsorbents and catalysts. Al2O3 nanoparticles are widely used in high-tech applications owing to their excellent properties. Besides, Bi-based oxides have been the center of attention for applications such as remediation of hazardous wastes and wastewater photochemical degradation of organic contaminants and remediation of hazardous wastes. In this research, the synthesis of Bi2O3-Al4Bi2O9 nanocomposite and its mechanical properties as a novel composition were investigated. The results showed that the prepared Bi2O3-Al4Bi2O9 sample exhibited the Al4Bi2O9 crystalline peaks. Additionally, the prepared nanocomposite showed no impurities. The mechanical properties of the Bi2O3-Al4Bi2O9 sample were improved in comparison with Al2O3, Bi2O3, and Bi2O3- Al2O3, which offer it as a promising alternative to Bi2O3-Al2O3 composite ceramic. 0 - 171 174 - - Shayan Askari Department of Chemistry, Najafabad Branch, Islamic Azad University Iran shayan_askari@ymail.com - - Majid Ghashang Department of Chemistry, Najafabad Branch, Islamic Azad University Iran info@jourcc.com - - Ghazal Sohrabi Department of Chemistry, Najafabad Branch, Islamic Azad University Iran info@jourcc.com Nanocomposite Catalyst Al2O3 Bi2O3-Al4Bi2O9 Novel composition [1] L. Bazli, A. Khavandi, M.A. Boutorabi, M. Karrabi, Morphology and viscoelastic behavior of silicone rubber/EPDM/Cloisite 15A nanocomposites based on Maxwell model, Iranian Polymer Journal 25(11) (2016) 907-918. ##[2] L. Bazli, A. Khavandi, M.A. Boutorabi, M. Karrabi, Correlation between viscoelastic behavior and morphology of nanocomposites based on SR/EPDM blends compatibilized by maleic anhydride, Polymer 113 (2017) 156-166. ##[3] E. Thostenson, C. Li, T. Chou, Nanocomposites in context, Composites Science and Technology 65(3-4) (2005) 491-516. ##[4] F. Hussain, M. Hojjati, M. Okamoto, R.E. Gorga, Review article: Polymer-matrix Nanocomposites, Processing, Manufacturing, and Application: An Overview, Journal of Composite Materials 40(17) (2006) 1511-1575. ##[5] L. Bazli, M.H. Bagherian, M. Karrabi, F. Abbassi‐Sourki, H. Azizi, Effect of starch ratio and compatibilization on the viscoelastic behavior of POE/starch blends, Journal of Applied Polymer Science 137(29) (2020) 48877. ##[6] J.R. Gaudet, A. de la Riva, E.J. Peterson, T. Bolin, A.K. Datye, Improved Low-Temperature CO Oxidation Performance of Pd Supported on La-Stabilized Alumina, ACS Catalysis 3(5) (2013) 846-855. ##[7] H. Purón, J.L. Pinilla, C. Berrueco, J.A. Montoya de la Fuente, M. Millán, Hydrocracking of Maya Vacuum Residue with NiMo Catalysts Supported on Mesoporous Alumina and Silica–Alumina, Energy and Fuels 27(7) (2013) 3952-3960. ##[8] M.M. Ibrahim, Cr2O3/Al2O3 as adsorbent: Physicochemical properties and adsorption behaviors towards removal of Congo red dye from water, Journal of Environmental Chemical Engineering 7(1) (2019) 102848. ##[9] L.M. Camacho, A. Torres, D. Saha, S. Deng, Adsorption equilibrium and kinetics of fluoride on sol–gel-derived activated alumina adsorbents, Journal of Colloid and Interface Science 349(1) (2010) 307-313. ##[10] J. Li, L. Xu, P. Sun, P. Zhai, X. Chen, H. Zhang, Z. Zhang, W. Zhu, Novel application of red mud: Facile hydrothermal-thermal conversion synthesis of hierarchical porous AlOOH and Al2O3 microspheres as adsorbents for dye removal, Chemical Engineering Journal 321 (2017) 622-634. ##[11] K. Yang, Y. Li, Z. Zhao, Z. Tian, Y. Lai, Amorphous porous layered-Al2O3 derived from AlFu MOFs as an adsorbent for removing fluorine ions in industrial ZnSO4 solution, Chemical Engineering Research and Design 153 (2020) 562-571. ##[12] A. Khaleel, P.N. Kapoor, K.J. Klabunde, Nanocrystalline metal oxides as new adsorbents for air purification, Nanostructured Materials 11(4) (1999) 459-468. ##[13] K. Hristovski, A. Baumgardner, P. Westerhoff, Selecting metal oxide nanomaterials for arsenic removal in fixed bed columns: From nanopowders to aggregated nanoparticle media, Journal of Hazardous Materials 147(1) (2007) 265-274. ##[14] F. Mirjalili, M. Hasmaliza, L.C. Abdullah, Size-controlled synthesis of nano α-alumina particles through the sol–gel method, Ceramics International 36(4) (2010) 1253-1257. ##[15] S. Motaghi, M. Farahmandjou, Structural and optoelectronic properties of Ce–Al2O3 nanoparticles prepared by sol-gel precursors, Materials Research Express 6(4) (2019) 045008. ##[16] M. Farahmandjou, N. Golabiyan, Synthesis and characterization of Alumina (Al2O3) nanoparticles prepared by simple sol-gel method, International Journal of Bio-Inorganic Hybrid Nanomaterials 5(1) (2016) 73-77. ##[17] M. Salehi, E. Arabsarhangi, Solution combustion synthesis using Schiff-base aluminum complex without fuel and optical property investigations of alumina nanoparticles, International Nano Letters 5(3) (2015) 141-146. ##[18] M. Hakimi, M. Morvaridi, H.A. Hosseini, P. Alimard, Preparation, characterization, and photocatalytic activity of Bi2O3–Al2O3 nanocomposite, Polyhedron 170 (2019) 523-529. ##[19] Z.N. Adamian, H.V. Abovian, V.M. Aroutiounian, Smoke sensor on the base of Bi2O3 sesquioxide, Sensors and Actuators B: Chemical 35(1) (1996) 241-243. ##[20] L. Leontie, M. Caraman, M. Alexe, C. Harnagea, Structural and optical characteristics of bismuth oxide thin films, Surface Science 507-510 (2002) 480-485. ##[21] L. Leontie, M. Caraman, M. Delibaş, G.I. Rusu, Optical properties of bismuth trioxide thin films, Materials Research Bulletin 36(9) (2001) 1629-1637. ##[22] V. Fruth, M. Popa, D. Berger, R. Ramer, M. Gartner, A. Ciulei, M. Zaharescu, Deposition and characterisation of bismuth oxide thin films, Journal of the European Ceramic Society 25(12) (2005) 2171-2174. ##[23] D. Kulkarni, I.E. Wachs, Isopropanol oxidation by pure metal oxide catalysts: number of active surface sites and turnover frequencies, Applied Catalysis A: General 237(1) (2002) 121-137. ##[24] T.-K. Tseng, J. Choi, D.-W. Jung, M. Davidson, P.H. Holloway, Three-Dimensional Self-Assembled Hierarchical Architectures of Gamma-Phase Flowerlike Bismuth Oxide, ACS Applied Materials and Interfaces 2(4) (2010) 943-946. ##[25] B. Yang, M. Mo, H. Hu, C. Li, X. Yang, Q. Li, Y. Qian, A Rational Self-Sacrificing Template Route to β-Bi2O3 Nanotube Arrays, European Journal of Inorganic Chemistry 2004(9) (2004) 1785-1787. ##[26] K. Karthik, K.S. Devi, D. Pinheiro, S. Sugunan, Influence of surfactant on the phase transformation of Bi2O3 and its photocatalytic activity, Australian Journal of Chemistry 72(4) (2019) 295-304. ##[27] M. Al-Buriahi, F. El-Agawany, C. Sriwunkum, H. Akyıldırım, H. Arslan, B. Tonguc, R. El-Mallawany, Y. Rammah, Influence of Bi2O3/PbO on nuclear shielding characteristics of lead-zinc-tellurite glasses, Physica B: Condensed Matter 581 (2020) 411946. ##[28] M.K. Trivedi, R.M. Tallapragada, A. Branton, D. Trivedi, G. Nayak, O. Latiyal, S. Jana, Evaluation of atomic, physical, and thermal properties of bismuth oxide powder: An impact of biofield energy treatment, (2015). ##[29] S. Thakur, V. Thakur, A. Kaur, L. Singh, Synthesis and the study of structural, thermal and optical properties of (100-x) Bi2O3-x (BaO-TiO2) glass system, Optik 223 (2020) 165646. ##[30] B.-H. Yun, Study on Bismuth-based Oxide Ion Conductors with High Performance and Durability for Lower Temperature Solid Oxide Fuel Cells, DGIST, 2020. ##[31] O.B. Dehkordi, A.M. Hadian, Joining of Alumina to Alumina Using Bismuth Oxide Nano Powder, Procedia Materials Science 11 (2015) 733-737. ##[32] K. Kohama, Joining of alumina ceramics using silicon–magnesium composite filler for high-temperature applications, Science and Technology of Welding and Joining 25(5) (2020) 383-390. ##[33] F. Cui, Z. Xu, R. Chu, X. He, X. Guo, G. Li, Low temperature sintering ZnO-Bi2O3 based varistor ceramics with low electrical breakdown voltage and high nonlinear coefficient, Ceramics International (2020). ##[34] Y. Liao, Y. Wang, Z. Chen, X. Wang, J. Li, R. Guo, C. Liu, G. Gan, G. Wang, Y. Li, Microstructure and enhanced magnetic properties of low-temperature sintered LiZnTiMn ferrite ceramics with Bi2O3-Al2O3 additive, Ceramics International 46(1) (2020) 487-492. ##[35] A.Y. Neiman, A.V. Tanskaya, E.V. Tsipis, L.M. Fyodorova, B.D. Antonov, Effect of size factor on mechanism of interaction between Al2O3 and Bi2O3 and conductivity of composite on their basis, Nanotechnologies in Russia 6(3-4) (2011) 218-226. ##[36] I. Zālīte, L. Grase, S. Lagzdina, D. Rašmane, Porous Ceramics from Al2O3 Nanopowders, Key Engineering Materials 850 (2020) 273-278. ##[37] S.K. Shubham, R. Purohit, P. Yadav, R. Rana, Study of nano-fillers embedded in polymer matrix composites to enhance its properties–A review, Materials Today: Proceedings (2020). ##[38] Y. Dong, A. Ma, D. Zhang, Y. Gao, H. Li, Preparation of high-performance α-Bi2O3 photocatalysts and their photocatalytic activity, Surface Innovations (2020) 1-9. ##[39] V. Amendola, I.D. Amans, Y. Ishikawa, N. Koshizaki, S. Scirè, G. Compagnini, S. Reichenberger, I.S. Barcikowski, Room‐Temperature Laser Synthesis in Liquid of Oxide, Metal‐Oxide Core‐Shells, and Doped Oxide Nanoparticles, Chemistry (Weinheim an der Bergstrasse, Germany) 26(42) (2020) 9206. ##[40] M. Parashar, V.K. Shukla, R. Singh, Metal oxides nanoparticles via sol–gel method: a review on synthesis, characterization and applications, Journal of Materials Science: Materials in Electronics (2020) 1-21. ##[41] P. Karasiński, A. Domanowska, E. Gondek, A. Sikora, C. Tyszkiewicz, M. Skolik, Homogeneity of sol-gel derived silica-titania waveguide films–Spectroscopic and AFM studies, Optics and Laser Technology 121 (2020) 105840. ##[42] H. Ibrahimov, L. Afandiyeva, S. Malikli, G. Rustamli, R. Babali, Obtaining of nanostructured γ-Al2O3 by sol-gel method, Thermam (2020) 83. ##[43] S. Rahimi, F. SharifianJazi, A. Esmaeilkhanian, M. Moradi, A.H.S. Samghabadi, Effect of SiO2 content on Y-TZP/Al2O3 ceramic-nanocomposite properties as potential dental applications, Ceramics International (2020). ##[44] A. Masoudian, M. Karbasi, F. SharifianJazi, A. Saidi, Developing Al2O3-TiC in-situ nanocomposite by SHS and analyzingtheeffects of Al content and mechanical activation on microstructure, Journal of Ceramic Processing Research 14(4) (2013) 486-491. ##[45] A. Kazemzadeh, M.A. Meshkat, H. Kazemzadeh, M. Moradi, R. Bahrami, R. Pouriamanesh, Preparation of graphene nanolayers through surfactant-assisted pure shear milling method, Journal of Composites and Compounds 1(1) (2019) 25-30.##

1 - Thermal conductivity, viscosity and heat transfer process in nanofluids: A critical review https://www.jourcc.com/index.php/jourcc/article/view/jcc243 10.29252/jcc.2.4.3 1 ‎Heat transfer efficiency has always been at the center of attractions for many researchers and industries and demand for higher efficiency methods and materials are increased in the last decades. One of the effective methods to enhance the thermal performance of instruments is using nanofluids as a solid-liquid suspension. In the present paper, the thermal conductivity, viscosity, and heat transfer process of the nanofluids are discussed. The effect of volume fraction, temperature, particle size, shape, base fluid type, and other factors on thermal conductivity, viscosity, and convective heat transfer coefficient of nanofluids are presented. Also, the preparation methods of nanofluids are exhibited and the stability and the effective factors on the stability of nanofluids are brought in the manuscript. Besides, a summarized number of experimental and mathematical studies about the thermal conductivity, viscosity, and stability of nanofluids are listed, compared, and analyzed. The works about the Nusselt number in fluids and nanofluids are presented in detail to determine the future challenges of nanofluids. 0 - 175 192 - - Saeed Noorzadeh Department of Mechanical Engineering, University of Mohaghegh Ardabili Iran info@jourcc.com - - Farhad Sadegh Moghanlou Department of Mechanical Engineering, University of Mohaghegh Ardabili Iran f_moghanlou@uma.ac.ir - - Mohammad Vajdi Department of Mechanical Engineering, University of Mohaghegh Ardabili Iran info@jourcc.com - - Mohammad Ataei Department of Mechanical Engineering, University of Mohaghegh Ardabili Iran info@jourcc.com Nanofluid Heat transfer Thermal conductivity Convection [1] T. Gholizadeh, M. Vajdi, H. Rostamzadeh, A new trigeneration system for power, cooling, and freshwater production driven by a flash-binary geothermal heat source, Renew. Energy. 148 (2020) 31–43. doi:10.1016/j.renene.2019.11.154. ##[2] T. Gholizadeh, M. Vajdi, F. Mohammadkhani, Thermodynamic and thermoeconomic analysis of basic and modified power generation systems fueled by biogas, Energy Convers. Manag. 181 (2019) 463–475. doi:10.1016/j.enconman.2018.12.011. ##[3] T. Gholizadeh, M. Vajdi, H. Rostamzadeh, Freshwater and cooling production via integration of an ethane ejector expander transcritical refrigeration cycle and a humidification-dehumidification unit, Desalination. 477 (2020) 114259. doi:10.1016/j.desal.2019.114259. ##[4] T. Gholizadeh, M. Vajdi, H. Rostamzadeh, A new biogas-fueled bi-evaporator electricity/cooling cogeneration system: Exergoeconomic optimization, Energy Convers. Manag. 196 (2019) 1193–1207. doi:10.1016/j.enconman.2019.06.053. ##[5] F. Yekani, S., Abdi Aghdam, E., Sadegh Moghanlo, Experimental study of The Performance and e xhaust gas emissions Response of A Spark Ignition Engine to Adding Natural Gas to Gasoline in CR=11., Int. J. Ind. Math. 11 (2019) 307–317. ##[6] T. Gholizadeh, M. Vajdi, H. Rostamzadeh, Energy and exergy evaluation of a new bi-evaporator electricity/cooling cogeneration system fueled by biogas, J. Clean. Prod. 233 (2019) 1494–1509. doi:10.1016/j.jclepro.2019.06.086. ##[7] T. Gholizadeh, M. Vajdi, H. Rostamzadeh, Exergoeconomic optimization of a new trigeneration system driven by biogas for power, cooling, and freshwater production, Energy Convers. Manag. 205 (2020) 112417. doi:10.1016/j.enconman.2019.112417. ##[8] S.M.F. Yekani S, Abdi Aghdam E, Performance Response of a Spark Ignition Engine to Adding Natural Gas to Gasoline on Lean-Burn Condition in 10 Compression Ratio., Modares Mech. Eng. 20 (2020) 1691–1699. ##[9] M. Namazizadeh, M. Talebian Gevari, M. Mojaddam, M. Vajdi, Optimization of the Splitter Blade Configuration and Geometry of a Centrifugal Pump Impeller using Design of Experiment, J. Appl. Fluid Mech. 13 (2020) 89–101. doi:10.29252/jafm.13.01.29856. ##[10] F.S. Moghanlou, A.S. Khorrami, E. Esmaeilzadeh, H. Aminfar, Experimental study on electrohydrodynamically induced heat transfer enhancement in a minichannel, Exp. Therm. Fluid Sci. 59 (2014) 24–31. doi:10.1016/j.expthermflusci.2014.07.019. ##[11] R.L. Webb, N.-H. Kim, principles enhanced heat transfer, CRC Press, 2005. ##[12] J.S. Moghanlou FS, Ghazanfari Jajin E, Vajdy Hokmabad M, On the Experimental and Numerical Droplet Generation in the Ordinary and Modified Micro channels with Oval Obstacle, Modares Mech. Eng. 20 (2020). ##[13] Y. Sui, P.S. Lee, C.J. Teo, An experimental study of flow friction and heat transfer in wavy microchannels with rectangular cross section, Int. J. Therm. Sci. 50 (2011) 2473–2482. doi:10.1016/j.ijthermalsci.2011.06.017. ##[14] M. Shahedi Asl, M. Sakkaki, F. Sadegh Moghanlou, S. Parvizi, H. Baghbanijavid, A. Babapoor, Phase change materials as quenching media for heat treatment of 42CrMo4 steels, J. Cent. South Univ. (2020). ##[15] M. Fattahi, K. Vaferi, M. Vajdi, F. Sadegh Moghanlou, A. Sabahi Namini, M. Shahedi Asl, Aluminum nitride as an alternative ceramic for fabrication of microchannel heat exchangers: A numerical study, Ceram. Int. 46 (2020) 11647–11657. doi:10.1016/j.ceramint.2020.01.195. ##[16] T. Dehghani, F. Sadegh Moghanlou, M. Vajdi, M. Shahedi Asl, M. Shokouhimehr, M. Mohammadi, Mixing enhancement through a micromixer using topology optimization, Chem. Eng. Res. Des. 161 (2020) 187–196. doi:10.1016/j.cherd.2020.07.008. ##[17] M. Namazizadeh, R. Haghighi khoshkhoo, F. Joda, Effect of Air Gap on thermohydraulic performance of finned tube bundles, Therm. Sci. Eng. Prog. 20 (2020) 100687. doi:10.1016/j.tsep.2020.100687. ##[18] M. Vajdi, M. Shahedi Asl, S. Nekahi, F. Sadegh Moghanlou, S. Jafargholinejad, M. Mohammadi, Numerical assessment of beryllium oxide as an alternative material for micro heat exchangers, Ceram. Int. 46 (2020) 19248–19255. doi:10.1016/j.ceramint.2020.04.263. ##[19] M. Vajdi, F. Sadegh Moghanlou, E. Ranjbarpour Niari, M. Shahedi Asl, M. Shokouhimehr, Heat transfer and pressure drop in a ZrB2 microchannel heat sink: A numerical approach, Ceram. Int. 46 (2020) 1730–1735. doi:10.1016/j.ceramint.2019.09.146. ##[20] F. Sadegh Moghanlou, S. Noorzadeh, M. Ataei, M. Vajdi, M. Shahedi Asl, E. Esmaeilzadeh, Experimental investigation of heat transfer and pressure drop in a minichannel heat sink using Al2O3 and TiO2–water nanofluids, J. Brazilian Soc. Mech. Sci. Eng. 42 (2020) 315. doi:10.1007/s40430-020-02403-5. ##[21] M.U. Sajid, H.M. Ali, Recent advances in application of nanofluids in heat transfer devices: A critical review, Renew. Sustain. Energy Rev. 103 (2019) 556–592. doi:10.1016/j.rser.2018.12.057. ##[22] J.A. Choi, S U.S.; Eastman, No Title, in: Enhancing Therm. Conduct. Fluids with Nanoparticles, n.d.: pp. 99–106. ##[23] W.H. Choi S. Siginer DA, Developments and Applications of Non-Newtonian Flows, 1995. ##[24] M. Ataei, F. Sadegh Moghanlou, S. Noorzadeh, M. Vajdi, M. Shahedi Asl, Heat transfer and flow characteristics of hybrid Al2O3/TiO2–water nanofluid in a minichannel heat sink, Heat Mass Transf. 56 (2020) 2757–2767. doi:10.1007/s00231-020-02896-9. ##[25] S. Chakraborty, An investigation on the long-term stability of TiO2 nanofluid, Mater. Today Proc. 11 (2019) 714–718. doi:10.1016/j.matpr.2019.03.032. ##[26] H. Zhang, S. Wang, Y. Lin, M. Feng, Q. Wu, Stability, thermal conductivity, and rheological properties of controlled reduced graphene oxide dispersed nanofluids, Appl. Therm. Eng. 119 (2017) 132–139. doi:10.1016/j.applthermaleng.2017.03.064. ##[27] W. Yu, D.M. France, S.U.S. Choi, J.L. Routbort, Review and assessment of nanofluid technology for transportation and other applications., Argonne, IL, 2007. doi:10.2172/919327. ##[28] C.G. Granqvist, R.A. Buhrman, J. Wyns, A.J. Sievers, Far-Infrared Absorption in Ultrafine Al Particles, Phys. Rev. Lett. 37 (1976) 625–629. doi:10.1103/PhysRevLett.37.625. ##[29] J.-H. Lee, K.S. Hwang, S.P. Jang, B.H. Lee, J.H. Kim, S.U.S. Choi, C.J. Choi, Effective viscosities and thermal conductivities of aqueous nanofluids containing low volume concentrations of Al2O3 nanoparticles, Int. J. Heat Mass Transf. 51 (2008) 2651–2656. doi:10.1016/j.ijheatmasstransfer.2007.10.026. ##[30] J.A. Eastman, S.U.S. Choi, S. Li, W. Yu, L.J. Thompson, Anomalously increased effective thermal conductivities of ethylene glycol-based nanofluids containing copper nanoparticles, Appl. Phys. Lett. 78 (2001) 718–720. doi:10.1063/1.1341218. ##[31] W. Yu, H. Xie, L. Chen, Y. Li, Investigation of thermal conductivity and viscosity of ethylene glycol based ZnO nanofluid, Thermochim. Acta. 491 (2009) 92–96. doi:10.1016/j.tca.2009.03.007. ##[32] Y. Hwang, J.K. Lee, C.H. Lee, Y.M. Jung, S.I. Cheong, C.G. Lee, B.C. Ku, S.P. Jang, Stability and thermal conductivity characteristics of nanofluids, Thermochim. Acta. 455 (2007) 70–74. doi:10.1016/j.tca.2006.11.036. ##[33] M.A. Khairul, K. Shah, E. Doroodchi, R. Azizian, B. Moghtaderi, Effects of surfactant on stability and thermo-physical properties of metal oxide nanofluids, Int. J. Heat Mass Transf. 98 (2016) 778–787. doi:10.1016/j.ijheatmasstransfer.2016.03.079. ##[34] V. Fuskele, R.M. Sarviya, Recent developments in Nanoparticles Synthesis, Preparation and Stability of Nanofluids, Mater. Today Proc. 4 (2017) 4049–4060. doi:10.1016/j.matpr.2017.02.307. ##[35] A. Ghadimi, R. Saidur, H.S.C. Metselaar, A review of nanofluid stability properties and characterization in stationary conditions, Int. J. Heat Mass Transf. 54 (2011) 4051–4068. doi:10.1016/j.ijheatmasstransfer.2011.04.014. ##[36] M. Sakkaki, F. Sadegh Moghanlou, M. Vajdi, M. Shahedi Asl, M. Mohammadi, M. Shokouhimehr, Numerical simulation of heat transfer during spark plasma sintering of zirconium diboride, Ceram. Int. 46 (2020) 4998–5007. doi:10.1016/j.ceramint.2019.10.240. ##[37] F. Sadegh Moghanlou, M. Vajdi, J. Sha, A. Motallebzadeh, M. Shokouhimehr, M. Shahedi Asl, A numerical approach to the heat transfer in monolithic and SiC reinforced HfB. ##

1 - An overview of the development of composites containing Mg and Zn for drug delivery https://www.jourcc.com/index.php/jourcc/article/view/jcc244 10.29252/jcc.2.4.4 1 Drug delivery is known as the administration of drugs using suitable vehicle for achieving effective treatment with no unwanted effects. In recent years, various composite materials have been developed and evaluated for being used in different biomedical fields such as wound dressings, cardiac prosthesis, tissue engineering, and drug delivery. Zinc is the second most available element after Fe in our body. Nanoparticles based on metal oxides, such as zinc oxides and Zn-containing composites, can be considered as viable platforms for some biomedical uses, especially for drug delivery applications. Mg composite biomaterials are also suggested for diverse biomedical applications due to their good mechanical properties, biocompatibility, and bioactivity. This paper highlights applications of zinc and magnesium-based composites in development of drug delivery systems. 0 - 193 204 - - Firooze Niazvand School of Medicine, Abadan Faculty of Medical Sciences Iran info@jourcc.com - - Amir Cheshmi Department of Materials Engineering, Babol Noshirvani University of Technology Iran amir_cheshomi@yahoo.com - - Maryam Zand Department of Physics, Alzahra University Iran info@jourcc.com - - Reyhaneh Nasr Azadani Department of Biomaterials Nanotechnology and Tissue engineering, Isfahan University of Medical Sciences Iran info@jourcc.com - - Beena Kumari Department of Pharmaceutical Sciences, Indira Gandhi University India info@jourcc.com - - Ali Raza School of Biomedical Engineering, Shanghai Jiaotong University China info@jourcc.com - - Shima Nasibi Materials Science and Engineering Department, Shiraz University Iran info@jourcc.com Drug delivery Biomedical application Zinc oxide composite Mg composites [1] G. Tiwari, R. Tiwari, B. Sriwastawa, L. Bhati, S. Pandey, P. Pandey, S.K. Bannerjee, Drug delivery systems: An updated review, International journal of pharmaceutical investigation 2(1) (2012) 2. ## [2] Z. Goudarzi, A. Ijadi, A. Bakhtiari, S. Eskandarinezhad, N. Azizabadi, M.A. Jazi, Sr-doped bioactive glasses for biological applications, Journal of Composites and Compounds 2(3) (2020) 105-109. ## [3] X. Zhang, M. Cresswell, Inorganic controlled release technology, Inorg. Control. Release Technol. (2016). ## [4] J.-H. Kang, M.-H. Chun, M.-S. Cho, Y.-B. Kwon, J.-C. Choi, D.-W. Kim, C.- W. Park, E.-S. Park, Preparation and characterization of metformin hydrochloride controlled-release tablet using fatty acid coated granules, Drug Development and Industrial Pharmacy 46(5) (2020) 852-860. ## [5] C.J. Grande, F.G. Torres, C.M. Gomez, M.C. Bañó, Nanocomposites of bacterial cellulose/hydroxyapatite for biomedical applications, Acta Biomaterialia 5(5) (2009) 1605-1615. ## [6] J.P. Jose, S. Thomas, J. Kuruvilla, S. Malhotra, K. Goda, M.S. Sreekala, Advances in polymer composites: macro-and microcomposites—state of the art, new challenges, and opportunities, Polymer Composites; Wiley: Weinheim, Germany 1 (2012) 3-16. ## [7] H. Ullah, F. Wahid, H.A. Santos, T. Khan, Advances in biomedical and pharmaceutical applications of functional bacterial cellulose-based nanocomposites, Fig. 4. Preparation of composite scaﬀolds by the space holder technique.200 F. Niazvand et al. / Journal of Composites and Compounds 2 (2020) 193-204 Carbohydrate polymers 150 (2016) 330-352. ## [8] F. Sharifanjazi, A.H. Pakseresht, M.S. Asl, A. Esmaeilkhanian, H.W. Jang, M. Shokouhimehr, Hydroxyapatite consolidated by zirconia: applications for dental implant, Journal of Composites and Compounds 2(1) (2020) 26-34. ## [9] L. Bazli, B. Eftekhari Yekta, A. Khavandi, Preparation and Characterization of Sn-Containing Glasses for Brachytherapy Applications, Transactions of the Indian Ceramic Society 76(4) (2017) 242-246. ## [10] Y. Kameshima, H. Sasaki, T. Isobe, A. Nakajima, K. Okada, Synthesis of composites of sodium oleate/Mg–Al-ascorbic acid-layered double hydroxides for drug delivery applications, International journal of pharmaceutics 381(1) (2009) 34-39. ## [11] M. Abniki, A. Moghimi, F. Azizinejad, Fabrication of bionanocomposite based on LDH using biopolymer of gum arabic and chitosan-coating for sustained drug-release, Journal of the Serbian Chemical Society 85(5) (2020). ## [12] M. Abniki, A. Moghimi, F. Azizinejad, Synthesis of calcium‐layered double hydroxide based nanohybrid for controlled release of an anti‐inﬂammatory drug, Journal of the Chinese Chemical Society (2020). ## [13] W.-H. Lu, K.-D. Li, C.-H. Lu, L.G. Teoh, W.H. Wu, Y.C. Shen, Synthesis and characterization of mesoporous SiO2–CaO–P2O5 bioactive glass by sol–gel process, Materials transactions 54(5) (2013) 791-795. ## [14] J. Andersson, S. Areva, B. Spliethoﬀ, M. Lindén, Sol–gel synthesis of a multifunctional, hierarchically porous silica/apatite composite, Biomaterials 26(34) (2005) 6827-6835. ## [15] S.P. Hudson, R.F. Padera, R. Langer, D.S. Kohane, The biocompatibility of mesoporous silicates, Biomaterials 29(30) (2008) 4045-4055. ## [16] X. Li, X. Wang, H. Chen, P. Jiang, X. Dong, J. Shi, Hierarchically porous bioactive glass scaﬀolds synthesized with a PUF and P123 cotemplated approach, Chemistry of Materials 19(17) (2007) 4322-4326. ## [17] A. López-Noriega, D. Arcos, I. Izquierdo-Barba, Y. Sakamoto, O. Terasaki, M. Vallet-Regí, Ordered mesoporous bioactive glasses for bone tissue regeneration, Chemistry of Materials 18(13) (2006) 3137-3144. ## [18] X. Yan, X. Huang, C. Yu, H. Deng, Y. Wang, Z. Zhang, S. Qiao, G. Lu, D. Zhao, The in-vitro bioactivity of mesoporous bioactive glasses, Biomaterials 27(18) (2006) 3396-3403. ## [19] X. Yan, C. Yu, X. Zhou, J. Tang, D. Zhao, Highly ordered mesoporous bioactive glasses with superior in vitro bone‐forming bioactivities, Angewandte Chemie International Edition 43(44) (2004) 5980-5984. ## [20] M. Vašák, D.W. Hasler, Metallothioneins: new functional and structural insights, Current opinion in chemical biology 4(2) (2000) 177-183. ## [21] M.F. Heragh, S. Eskandarinezhad, A. Dehghan, Ni-Cu matrix composite reinforced with CNTs: preparation, characterization, wear and corrosion behavior, inhibitory eﬀects, Journal of Composites and Compounds 2(4) (2020) 123-128. ## [22] C.T. Chasapis, A.C. Loutsidou, C.A. Spiliopoulou, M.E. Stefanidou, Zinc and human health: an update, Archives of toxicology 86(4) (2012) 521-534. ## [23] E. Alhava, H. Olkkonen, J. Puittinen, V. Nokso-Koivisto, Zinc content of human cancellous bone, Acta Orthopaedica Scandinavica 48(1) (1977) 1-4. ## [24] H. Kim, S. Mondal, S. Bharathiraja, P. Manivasagan, M.S. Moorthy, J. Oh, Optimized Zn-doped hydroxyapatite/doxorubicin bioceramics system for efcient drug delivery and tissue engineering application, Ceramics International 44(6) (2018) 6062-6071. ## [25] Y. Su, I. Cockerill, Y. Wang, Y.-X. Qin, L. Chang, Y. Zheng, D. Zhu, Zincbased biomaterials for regeneration and therapy, Trends in biotechnology 37(4) (2019) 428-441. ## [26] Z. Gao, D. Zhang, X. Li, S. Jiang, Q. Zhang, Current status, opportunities and challenges in chemical conversion coatings for zinc, Colloids and Surfaces A: Physicochemical and Engineering Aspects 546 (2018) 221-236. ## [27] S. Parveen, R. Misra, S.K. Sahoo, Nanoparticles: a boon to drug delivery, therapeutics, diagnostics and imaging, Nanomedicine: Nanotechnology, Biology and Medicine 8(2) (2012) 147-166. ## [28] H.M. Xiong, ZnO nanoparticles applied to bioimaging and drug delivery, Advanced Materials 25(37) (2013) 5329-5335. ## [29] Z.Y. Zhang, Y.D. Xu, Y.Y. Ma, L.L. Qiu, Y. Wang, J.L. Kong, H.M. Xiong, Biodegradable ZnO@ polymer core–shell nanocarriers: pH‐triggered release of doxorubicin in vitro, Angewandte Chemie 125(15) (2013) 4221-4225. ## [30] G. Song, Control of biodegradation of biocompatable magnesium alloys, Corrosion science 49(4) (2007) 1696-1701. ## [31] A.H. Shahbaz, M. Esmaeilian, R. NasrAzadani, K. Gavanji, The eﬀect of MgF2 addition on the mechanical properties of hydroxyapatite synthesized via powder metallurgy, Journal of Composites and Compounds 1(1) (2019) 18-24. ## [32] S. Nasibi, K. Alimohammadi, L. Bazli, S. Eskandarinezhad, A. Mohammadi, N. Sheysi, TZNT alloy for surgical implant applications: A systematic review, Journal of Composites and Compounds 2(3) (2020) 62-68. ## [33] R. Erbel, C. Di Mario, J. Bartunek, J. Bonnier, B. de Bruyne, F.R. Eberli, P. Erne, M. Haude, B. Heublein, M. Horrigan, Temporary scaﬀolding of coronary arteries with bioabsorbable magnesium stents: a prospective, non-randomised multicentre trial, The Lancet 369(9576) (2007) 1869-1875. ## [34] M. Haude, R. Erbel, P. Erne, S. Verheye, H. Degen, D. Böse, P. Vermeersch, I. Wijnbergen, N. Weissman, F. Prati, Safety and performance of the drug-eluting absorbable metal scaﬀold (DREAMS) in patients with de-novo coronary lesions: 12 month results of the prospective, multicentre, frst-in-man BIOSOLVE-I trial, The Lancet 381(9869) (2013) 836-844. ## [35] M. Haude, H. Ince, A. Abizaid, R. Toelg, P.A. Lemos, C. von Birgelen, E.H. Christiansen, W. Wijns, F.-J. Neumann, C. Kaiser, Safety and performance of the second-generation drug-eluting absorbable metal scaﬀold in patients with de-novo coronary artery lesions (BIOSOLVE-II): 6 month results of a prospective, multicentre, non-randomised, frst-in-man trial, The Lancet 387(10013) (2016) 31-39. ## [36] B. Heublein, R. Rohde, V. Kaese, M. Niemeyer, W. Hartung, A. Haverich, Biocorrosion of magnesium alloys: a new principle in cardiovascular implant technology?, Heart 89(6) (2003) 651-656. ## [37] H. Li, H. Zhong, K. Xu, K. Yang, J. Liu, B. Zhang, F. Zheng, Y. Xia, L. Tan, D. Hong, Enhanced efcacy of sirolimus-eluting bioabsorbable magnesium alloy stents in the prevention of restenosis, Journal of Endovascular Therapy 18(3) (2011) 407-415. ## [38] R. Waksman, R. Erbel, C. Di Mario, J. Bartunek, B. de Bruyne, F.R. Eberli, P. Erne, M. Haude, M. Horrigan, C. Ilsley, Early-and long-term intravascular ultrasound and angiographic fndings after bioabsorbable magnesium stent implantation in human coronary arteries, JACC: Cardiovascular Interventions 2(4) (2009) 312-320. ## [39] R. Waksman, R. Pakala, P.K. Kuchulakanti, R. Baﬀour, D. Hellinga, R. Seabron, F.O. Tio, E. Wittchow, S. Hartwig, C. Harder, Safety and efcacy of bioabsorbable magnesium alloy stents in porcine coronary arteries, Catheterization and Cardiovascular Interventions 68(4) (2006) 607-617. ## [40] E. Wittchow, N. Adden, J. Riedmüller, C. Savard, R. Waksman, M. Braune, Bioresorbable drug-eluting magnesium-alloy scaﬀold: design and feasibility in a porcine coronary model, EuroIntervention 8(12) (2013) 1441-1450. ## [41] P. Zartner, R. Cesnjevar, H. Singer, M. Weyand, First successful implantation of a biodegradable metal stent into the left pulmonary artery of a preterm baby, Catheterization and Cardiovascular Interventions 66(4) (2005) 590-594. ## [42] M. Haude, H. Ince, A. Abizaid, R. Toelg, P.A. Lemos, C. von Birgelen, E.H. Christiansen, W. Wijns, F.-J. Neumann, C. Kaiser, Sustained safety and performance of the second-generation drug-eluting absorbable metal scaﬀold in patients with de novo coronary lesions: 12-month clinical results and angiographic fndings of the BIOSOLVE-II frst-in-man trial, European heart journal 37(35) (2016) 2701-2709. ## [43] M. Diba, O.-M. Goudouri, F. Tapia, A.R. Boccaccini, Magnesium-containing bioactive polycrystalline silicate-based ceramics and glass-ceramics for biomedical applications, Current opinion in solid state and materials science 18(3) (2014) 147-167. ## [44] Y. Bi, Y. Zheng, Y. Li, Microstructure and mechanical properties of sintered porous magnesium using polymethyl methacrylate as the space holder, Materials Letters 161 (2015) 583-586. ## [45] H. Bakhsheshi-Rad, E. Hamzah, M.P. Staiger, G.J. Dias, Z. Hadisi, M. Saheban, M. Kashefan, Drug release, cytocompatibility, bioactivity, and antibacterial activity of doxycycline loaded Mg-Ca-TiO2 composite scaﬀold, Materials and Design 139 (2018) 212-221. ## [46] K.K. Jain, Drug delivery systems-an overview, Drug delivery systems, Springer2008, pp. 1-50. ## [47] M. Arefan, M. Hojjati, I. Tajzad, A. Mokhtarzade, M. Mazhar, A. Jamavari, A review of Polyvinyl alcohol/Carboxiy methyl cellulose (PVA/CMC) composites for various applications, Journal of Composites and Compounds 2(3) (2020) 69- 76. ## [48] P. Abasian, M. Radmansouri, M.H. Jouybari, M.V. Ghasemi, A. Mohammadi, M. Irani, F.S. Jazi, Incorporation of magnetic NaX zeolite/DOX into the PLA/chitosan nanofbers for sustained release of doxorubicin against carcinoma cells death in vitro, International journal of biological macromolecules 121 (2019) 398-406. ## [49] H. Derendorf, L.J. Lesko, P. Chaikin, W.A. Colburn, P. Lee, R. Miller, R. Powell, G. Rhodes, D. Stanski, J. Venitz, Pharmacokinetic/pharmacodynamic modeling in drug research and development, The Journal of Clinical Pharmacology 40(12) (2000) 1399-1418. ## [50] S. Gopi, A. Amalraj, N.P. Sukumaran, J.T. Haponiuk, S. Thomas, Biopolymers and their composites for drug delivery: a brief review, Macromolecular Symposia, Wiley Online Library, 2018, p. 1800114. ## [51] G.R. Matzke, G.R. Aronoﬀ, A.J. Atkinson Jr, W.M. Bennett, B.S. Decker, K.-U. Eckardt, T. Golper, D.W. Grabe, B. Kasiske, F. Keller, Drug dosing consideration in patients with acute and chronic kidney disease—a clinical update fromF. Niazvanda et al. / Journal of Composites and Compounds 2 (2020) 193-204 201 Kidney Disease: Improving Global Outcomes (KDIGO), Kidney international 80(11) (2011) 1122-1137. ## [52] M.J. Munoz-Davila, Role of old antibiotics in the era of antibiotic resistance. Highlighted nitrofurantoin for the treatment of lower urinary tract infections, Antibiotics 3(1) (2014) 39-48. ## [53] J.J. De Waele, S. Carrette, M. Carlier, V. Stove, J. Boelens, G. Claeys, I. Leroux-Roels, E. Hoste, P. Depuydt, J. Decruyenaere, Therapeutic drug monitoring-based dose optimisation of piperacillin and meropenem: a randomised controlled trial, Intensive care medicine 40(3) (2014) 380-387. ## [54] S.K. Bardal, J.E. Waechter, D.S. Martin, Applied pharmacology, Elsevier Health Sciences2011. ## [55] W. Brand, M.E. Schutte, G. Williamson, J.J. van Zanden, N.H. Cnubben, J.P. Groten, P.J. van Bladeren, I.M. Rietjens, Flavonoid-mediated inhibition of intestinal ABC transporters may aﬀect the oral bioavailability of drugs, food-borne toxic compounds and bioactive ingredients, Biomedicine and pharmacotherapy 60(9) (2006) 508-519. ## [56] A.H. Chow, H.H. Tong, P. Chattopadhyay, B.Y. Shekunov, Particle engineering for pulmonary drug delivery, Pharmaceutical research 24(3) (2007) 411-437. ## [57] S. Amirhossein, A.-B. Aydin, Z. Habib, Polaroid-PET: a PET scanner with detectors ftted with polaroids for fltering unpolarized optical photons: a Monte Carlo simulation study, Physics in Medicine and Biology (2020). ## [58] A. Sanaat, H. Zaidi, Depth of interaction estimation in a preclinical PET scanner equipped with monolithic crystals coupled to SiPMs using a deep neural network, Applied Sciences 10(14) (2020) 4753. ## [59] A. Sanaat, H. Arabi, M.R. Ay, H. Zaidi, Novel preclinical PET geometrical concept using a monolithic scintillator crystal oﬀering concurrent enhancement in spatial resolution and detection sensitivity: a simulation study, Physics in Medicine and Biology 65(4) (2020) 045013. ## [60] A. Sanaat, H. Arabi, I. Mainta, V. Garibotto, H. Zaidi, Projection-space implementation of deep learning-guided low-dose brain PET imaging improves performance over implementation in image-space, Journal of Nuclear Medicine (2020) jnumed. 119.239327. ## [61] N. Kamaly, B. Yameen, J. Wu, O.C. Farokhzad, Degradable controlled-release polymers and polymeric nanoparticles: mechanisms of controlling drug release, Chemical reviews 116(4) (2016) 2602-2663. ## [62] J. Daraei, Production and characterization of PCL (Polycaprolactone) coated TCP/nanoBG composite scaﬀolds by sponge foam method for orthopedic applications, Journal of Composites and Compounds 2(1) (2020) 45-50. ## [63] X. Huang, S. Wu, X. Ke, X. Li, X. Du, Phosphonated pillar ## [5] arene-valved mesoporous silica drug delivery systems, ACS Applied Materials and Interfaces 9(23) (2017) 19638-19645. ## [64] N.G. Kotla, B. Chandrasekar, P. Rooney, G. Sivaraman, A. Larrañaga, K.V. Krishna, A. Pandit, Y. Rochev, Biomimetic lipid-based nanosystems for enhanced dermal delivery of drugs and bioactive agents, ACS Biomaterials Science and Engineering 3(7) (2017) 1262-1272. ## [65] A. Kazemzadeh, H. Kazemzadeh, Determination of Hg2+ by Diphenylcarbazone Compound in Polymer Film, Journal of Composites and Compounds 1(1) (2019) 30-35. ## [66] A. Nouri, B. Faraji Dizaji, N. Kianinejad, A. Jafari Rad, S. Rahimi, M. Irani, F. Sharifan Jazi, Simultaneous linear release of folic acid and doxorubicin from ethyl cellulose/chitosan/g‐C3N4/MoS2 core‐shell nanofbers and its anticancer properties, Journal of Biomedical Materials Research Part A (2020). ## [67] D. Liu, F. Yang, F. Xiong, N. Gu, The smart drug delivery system and its clinical potential, Theranostics 6(9) (2016) 1306. ## [68] Z. Wang, Y. Duan, Y. Duan, Application of polydopamine in tumor targeted drug delivery system and its drug release behavior, Journal of Controlled Release 290 (2018) 56-74. ## [69] J. Ma, N. Zhao, D. Zhu, Endothelial cellular responses to biodegradable metal zinc, ACS biomaterials science and engineering 1(11) (2015) 1174-1182. ## [70] F.S. Jazi, N. Parvin, M. Rabiei, M. Tahriri, Z.M. Shabestari, A.R. Azadmehr, Eﬀect of the synthesis route on the grain size and morphology of ZnO/Ag nanocomposite, Journal of Ceramic Processing Research 13(5) (2012) 523-526. ## [71] J. Jiang, J. Pi, J. Cai, The advancing of zinc oxide nanoparticles for biomedical applications, Bioinorganic chemistry and applications 2018 (2018). ## [72] Z. Zeng, X. Fang, W. Miao, Y. Liu, T. Maiyalagan, S. Mao, Electrochemically Sensing of Trichloroacetic Acid with Iron(II) Phthalocyanine and Zn-Based Metal Organic Framework Nanocomposites, ACS Sensors 4(7) (2019) 1934-1941. ## [73] W. Liu, Y. Pan, W. Xiao, H. Xu, D. Liu, F. Ren, X. Peng, J. Liu, Recent developments on zinc (ii) metal–organic framework nanocarriers for physiological pH-responsive drug delivery, MedChemComm 10(12) (2019) 2038-2051. ## [74] K. Dong, Y. Zhang, L. Zhang, Z. Wang, J. Ren, X. Qu, Facile preparation of metal− organic frameworks-based hydrophobic anticancer drug delivery nanoplatform for targeted and enhanced cancer treatment, Talanta 194 (2019) 703-708. ## [75] M. Zamani, M. Rostami, M. Aghajanzadeh, H. Kheiri Manjili, K. Rostamizadeh, H. Danafar, Mesoporous titanium dioxide@ zinc oxide–graphene oxide nanocarriers for colon-specifc drug delivery, Journal of Materials Science 53(3) (2018) 1634-1645. ## [76] J.W. Rasmussen, E. Martinez, P. Louka, D.G. Wingett, Zinc oxide nanoparticles for selective destruction of tumor cells and potential for drug delivery applications, Expert opinion on drug delivery 7(9) (2010) 1063-1077. ## [77] V. Karpina, V. Lazorenko, C. Lashkarev, V. Dobrowolski, L. Kopylova, V. Baturin, S. Pustovoytov, A.J. Karpenko, S. Eremin, P. Lytvyn, Zinc oxide–analogue of GaN with new perspective possibilities, Crystal Research and Technology: Journal of Experimental and Industrial Crystallography 39(11) (2004) 980-992. ## [78] X. Huang, X. Zheng, Z. Xu, C. Yi, Zno-based nanocarriers for drug delivery application: From passive to smart strategies, International journal of pharmaceutics 534(1-2) (2017) 190-194. ## [79] A.J. Rad, Synthesis of copper oxide nanoparticles on activated carbon for pollutant removal in Tartrazine structure, Journal of Composites and Compounds 2(3) (2020) 99-104. ## [80] A. Moghanian, A. Ghorbanoghli, M. Kazem‐Rostami, A. Pazhouheshgar, E. Salari, M. Saghaf Yazdi, T. Alimardani, H. Jahani, F. Sharifan Jazi, M. Tahriri, Novel antibacterial Cu/Mg‐substituted 58S‐bioglass: Synthesis, characterization and investigation of in vitro bioactivity, International Journal of Applied Glass Science 11(4) (2020) 685-698. ## [81] F. Sharifanjazi, M. Moradi, A. Abouchenari, A.H. Pakseresht, A. Esmaeilkhanian, M. Shokouhimehr, M.S. Asl, Eﬀects of Sr and Mg dopants on biological and mechanical properties of SiO2–CaO–P2O5 bioactive glass, Ceramics International (2020). ## [82] S. Ni, L. Chou, J. Chang, Preparation and characterization of forsterite (Mg- 2SiO4) bioceramics, Ceramics International 33(1) (2007) 83-88. ## [83] N. Sezer, Z. Evis, S.M. Kayhan, A. Tahmasebifar, M. Koç, Review of magnesium-based biomaterials and their applications, Journal of Magnesium and Alloys 6(1) (2018) 23-43. ## [84] A. Bordbar-Khiabani, B. Yarmand, M. Mozafari, Emerging magnesium-based biomaterials for orthopedic implantation, Thomas Telford Ltd, 2019. ## [85] Z. Wu, T. Tang, H. Guo, S. Tang, Y. Niu, J. Zhang, W. Zhang, R. Ma, J. Su, C. Liu, In vitro degradability, bioactivity and cell responses to mesoporous magnesium silicate for the induction of bone regeneration, Colloids and Surfaces B: Biointerfaces 120 (2014) 38-46. ## [86] A. Bigham, S.A. Hassanzadeh-Tabrizi, M. Rafenia, H. Salehi, Ordered mesoporous magnesium silicate with uniform nanochannels as a drug delivery system: The eﬀect of calcination temperature on drug delivery rate, Ceramics International 42(15) (2016) 17185-17191. ## [87] M. Vallet-Regi, Bio-ceramics with clinical applications, John Wiley and Sons2014. ## [88] P. Wu, D.W. Grainger, Drug/device combinations for local drug therapies and infection prophylaxis, Biomaterials 27(11) (2006) 2450-2467. ## [89] H. Dong, Q. Li, C. Tan, N. Bai, P. Cai, Bi-directional controlled release of ibuprofen and Mg2+ from magnesium alloys coated by multifunctional composite, Materials Science and Engineering: C 68 (2016) 512-518. ## [90] J. Tian, S. Shen, C. Zhou, X. Dang, Y. Jiao, L. Li, S. Ding, H. Li, Investigation of the antimicrobial activity and biocompatibility of magnesium alloy coated with HA and antimicrobial peptide, Journal of Materials Science: Materials in Medicine 26(2) (2015) 66. ## [91] J. Zhang, Z. Wen, M. Zhao, G. Li, C. Dai, Eﬀect of the addition CNTs on performance of CaP/chitosan/coating deposited on magnesium alloy by electrophoretic deposition, Materials Science and Engineering: C 58 (2016) 992-1000. ## [92] A. Morawska-Chochół, P. Domalik-Pyzik, J. Chłopek, B. Szaraniec, J. Sterna, M. Rzewuska, M. Boguń, R. Kucharski, P. Mielczarek, Gentamicin release from biodegradable poly-l-lactide based composites for novel intramedullary nails, Materials Science and Engineering: C 45 (2014) 15-20. ## [93] A. Kazemzadeh, M.A. Meshkat, H. Kazemzadeh, M. Moradi, R. Bahrami, R. Pouriamanesh, Preparation of graphene nanolayers through surfactant-assisted pure shear milling method, Journal of Composites and Compounds 1(1) (2019) 25-30. ## [94] W.E. Teo, S. Ramakrishna, A review on electrospinning design and nanofbre assemblies, Nanotechnology 17(14) (2006) R89. ## [95] L.A. Mercante, V.P. Scagion, F.L. Migliorini, L.H. Mattoso, D.S. Correa, Electrospinning-based (bio) sensors for food and agricultural applications: A review, TrAC Trends in Analytical Chemistry 91 (2017) 91-103. ## [96] M. Jiménez, C. Abradelo, J. San Román, L. Rojo, Bibliographic review on the state of the art of strontium and zinc based regenerative therapies. Recent developments and clinical applications, Journal of materials chemistry B 7(12) (2019)202 F. Niazvand et al. / Journal of Composites and Compounds 2 (2020) 193-204 1974-1985. ## [97] T.J. Sill, H.A. Von Recum, Electrospinning: applications in drug delivery and tissue engineering, Biomaterials 29(13) (2008) 1989-2006. ## [98] Y. Qian, Solvothermal Synthesis of Nanocrystalline III–V Semiconductors, Advanced Materials 11(13) (1999) 1101-1102. ## [99] C. Wang, Z.-X. Deng, Y. Li, The synthesis of nanocrystalline anatase and rutile titania in mixed organic media, Inorganic Chemistry 40(20) (2001) 5210-5214. ## [100] K. Kaviyarasu, E. Manikandan, P. Paulraj, S. Mohamed, J. Kennedy, One dimensional well-aligned CdO nanocrystal by solvothermal method, Journal of alloys and compounds 593 (2014) 67-70. ## [101] C.-S. Kim, B.K. Moon, J.-H. Park, S. Tae Chung, S.-M. Son, Synthesis of nanocrystalline TiO2 in toluene by a solvothermal route, Journal of Crystal Growth 254(3) (2003) 405-410. ## [102] M. Kang, Synthesis of Fe/TiO2 photocatalyst with nanometer size by solvothermal method and the eﬀect of H 2O addition on structural stability and photodecomposition of methanol, Journal of Molecular Catalysis A: Chemical 197(1) (2003) 173-183. ## [103] S. Yin, Y. Fujishiro, J. Wu, M. Aki, T. Sato, Synthesis and photocatalytic properties of fbrous titania by solvothermal reactions, Journal of Materials Processing Technology 137(1-3) (2003) 45-48. ## [104] S.M. Gupta, M. Tripathi, A review on the synthesis of TiO2 nanoparticles by solution route, Central European Journal of Chemistry 10(2) (2012) 279-294. ## [105] F.L. Theiss, G.A. Ayoko, R.L. Frost, Synthesis of layered double hydroxides containing Mg2+, Zn2+, Ca2+ and Al3+ layer cations by co-precipitation methods—A review, Applied Surface Science 383 (2016) 200-213. ## [106] M. Bukhtiyarova, A review on eﬀect of synthesis conditions on the formation of layered double hydroxides, Journal of Solid State Chemistry 269 (2019) 494-506. ## [107] V. Solovov, N. Nikolenko, V. Kovalenko, V. Kotok, A. Burkov, D. Kondrat’ev, O. Chernovа, S. Zhukovin, Synthesis of Ni (II)-Ti (IV) layered double hydroxides using coprecipitation at high supersaturation method, ARPN Journal of Engineering and Applied Sciences 13(24) (2018) 9652-9656. ## [108] X. Duan, D.G. Evans, Layered double hydroxides, Springer Science and Business Media2006. ## [109] H.W. Olfs, L.O. Torres-Dorante, R. Eckelt, H. Kosslick, Comparison of different synthesis routes for Mg–Al layered double hydroxides (LDH): Characterization of the structural phases and anion exchange properties, Applied Clay Science 43(3) (2009) 459-464. ## [110] L. Bazli, M. Siavashi, A. Shiravi, A review of carbon nanotube/TiO2 composite prepared via sol-gel method, Journal of Composites and Compounds 1(1) (2019) 1-9. ## [111] A. Bakhtiari, A. Cheshmi, M. Naeimi, S.M. Fathabad, M. Aliasghari, A.M. Chahardehi, S. Hassani, V. Elhami, Synthesis and characterization of the novel 80S bioactive glass: bioactivity,‎ biocompatibility, cytotoxicity, Journal of Composites and Compounds 2(4) (2020) 110-114. ## [112] L. Armelao, D. Barreca, M. Bertapelle, G. Bottaro, C. Sada, E. Tondello, A sol–gel approach to nanophasic copper oxide thin flms, Thin Solid Films 442(1) (2003) 48-52. ## [113] F.S. Jazi, N. Parvin, M. Tahriri, M. Alizadeh, S. Abedini, M. Alizadeh, The relationship between the synthesis and morphology of SnO2-Ag2O nanocomposite, Synthesis and Reactivity in Inorganic, Metal-Organic, and Nano-Metal Chemistry 44(5) (2014) 759-764. ## [114] M. Alizadeh, F. Sharifanjazi, E. Haghshenasjazi, M. Aghakhani, L. Rajabi, Production of nanosized boron oxide powder by high-energy ball milling, Synthesis and Reactivity in Inorganic, Metal-Organic, and Nano-Metal Chemistry 45(1) (2015) 11-14. ## [115] L.S. Cividanes, T.M. Campos, L.A. Rodrigues, D.D. Brunelli, G.P. Thim, Review of mullite synthesis routes by sol–gel method, Journal of Sol-Gel Science and Technology 55(1) (2010) 111-125. ## [116] M. Gonçalves, Sol-gel silica nanoparticles in medicine: A natural choice. Design, synthesis and products, Molecules 23(8) (2018) 2021. ## [117] S. Devaraju, K. Krishnadevi, E. Naveena, M. Alagar, Eco-friendly fully bio-based polybenzoxazine-silica hybrid materials by sol–gel approach, Polymer Bulletin (2020) 1-10. ## [118] H. Böttcher, P. Slowik, W. Süß, Sol-gel carrier systems for controlled drug delivery, Journal of sol-gel science and technology 13(1-3) (1998) 277-281. ## [119] M. Catauro, E. Tranquillo, F. Barrino, I. Blanco, F. Dal Poggetto, D. Naviglio, Drug release of hybrid materials containing Fe (II) citrate synthesized by sol-gel technique, Materials 11(11) (2018) 2270. ## [120] Y. Ding, W. Li, A. Correia, Y. Yang, K. Zheng, D. Liu, D.W. Schubert, A.R. Boccaccini, H.A. Santos, J.A. Roether, Electrospun polyhydroxybutyrate/poly (ε-caprolactone)/Sol–gel-derived silica hybrid scaﬀolds with drug releasing function for bone tissue engineering applications, ACS applied materials and interfaces 10(17) (2018) 14540-14548. ## [121] M. Catauro, F. Barrino, G. Dal Poggetto, M. Milazzo, I. Blanco, S.V. Ciprioti, Structure, drug absorption, bioactive and antibacterial properties of sol-gel SiO2/ ZrO 2 materials, Ceramics International (2020). ## [122] S.K. Sahoo, S. Barik, G. Dehury, S. Dhala, S. Kanungo, B.B. Barik, K.K. Puhan, Evaluation of controlled release theophylline microspheres prepared with cellulose acetate using solvent evaporation method, Tropical Journal of Pharmaceutical Research 10(2) (2011). ## [123] S. Jaraswekin, S. Prakongpan, R. Bodmeier, Eﬀect of poly (lactide-co-glycolide) molecular weight on the release of dexamethasone sodium phosphate from microparticles, Journal of microencapsulation 24(2) (2007) 117-128. ## [124] S. Freitas, H.P. Merkle, B. Gander, Microencapsulation by solvent extraction/evaporation: reviewing the state of the art of microsphere preparation process technology, Journal of Controlled Release 102(2) (2005) 313-332. ## [125] J. Emami, H. Hamishehkar, A.R. Najafabadi, K. Gilani, M. Minaiyan, H. Mahdavi, A. Nokhodchi, A Novel Approach to Prepare Insulin-Loaded Poly (Lactic-Co-Glycolic Acid) Microcapsules and the Protein Stability Study, Journal of Pharmaceutical Sciences 98(5) (2009) 1712-1731. ## [126] M.L. Manca, Chitosan and PLGA microspheres as drug delivery system against pulmonary mycobacteria infections, (2007). ## [127] M. Hoppel, D. Mahrhauser, C. Stallinger, F. Wagner, M. Wirth, C. Valenta, Natural polymer‐stabilized multiple water‐in‐oil‐in‐water emulsions: a novel dermal drug delivery system for 5‐ﬂuorouracil, Journal of Pharmacy and Pharmacology 66(5) (2014) 658-667. ## [128] H. Yang, Y. Hao, Q. Liu, Z. Mi, Z. Wang, L. Zhu, Q. Feng, N. Hu, Preparation and in vitro study of hydrochloric norvancomycin encapsulated poly (d, l-lactide-co-glycolide, PLGA) microspheres for potential use in osteomyelitis, Artifcial cells, nanomedicine, and biotechnology 45(7) (2017) 1326-1330. ## [129] M. Li, O. Rouaud, D. Poncelet, Microencapsulation by solvent evaporation: State of the art for process engineering approaches, International Journal of Pharmaceutics 363(1) (2008) 26-39. ## [130] W.M. Obeidat, Recent patents review in microencapsulation of pharmaceuticals using the emulsion solvent removal methods, Recent patents on drug delivery and formulation 3(3) (2009) 178-192. ## [131] Y. Maa, C. Hsu, Eﬀect of primary emulsions on microsphere size and protein-loading in the double emulsion process, Journal of microencapsulation 14(2) (1997) 225-241. ## [132] D. Noviendri, Microencapsulation of Fucoxanthin by Water-in-Oil-in-Water (W/O/W) Double Emulsion Solvent Evaporation Method: A Review, Squalen Bulletin of Marine and Fisheries Postharvest and Biotechnology 9(3) (2014). ## [133] Y.-Y. Yang, T.-S. Chung, N.P. Ng, Morphology, drug distribution, and in vitro release profles of biodegradable polymeric microspheres containing protein fabricated by double-emulsion solvent extraction/evaporation method, Biomaterials 22(3) (2001) 231-241. ## [134] R. Zhang, L. Gao, Preparation of nanosized titania by hydrolysis of alkoxide titanium in micelles, Materials research bulletin 37(9) (2002) 1659-1666. ## [135] A.S. Narang, D. Delmarre, D. Gao, Stable drug encapsulation in micelles and microemulsions, International journal of pharmaceutics 345(1-2) (2007) 9-25. ## [136] M.A. Malik, M.Y. Wani, M.A. Hashim, Microemulsion method: A novel route to synthesize organic and inorganic nanomaterials: 1st Nano Update, Arabian Journal of Chemistry 5(4) (2012) 397-417. ## [137] S.F. Chin, A. Azman, S.C. Pang, Size Controlled Synthesis of Starch Nanoparticles by a Microemulsion Method, Journal of Nanomaterials 2014 (2014) 763736. ## [138] H. Liu, J. Mei, Y. Xu, L. Tang, D. Chen, Y. Zhu, S. Huang, T.J. Webster, H. Ding, Improving The Oral Absorption Of Nintedanib By A Self-Microemulsion Drug Delivery System: Preparation And In Vitro/In Vivo Evaluation, International Journal of Nanomedicine 14 (2019) 8739. ## [139] M.B. de Jesus, A. Radaic, I.S. Zuhorn, E. de Paula, Microemulsion extrusion technique: a new method to produce lipid nanoparticles, Journal of nanoparticle research 15(10) (2013) 1960. ## [140] S.P. Callender, J.A. Mathews, K. Kobernyk, S.D. Wettig, Microemulsion utility in pharmaceuticals: Implications for multi-drug delivery, International journal of pharmaceutics 526(1-2) (2017) 425-442. ## [141] B. Yan, Y. Gu, J. Zhao, Y. Liu, L. Wang, Y. Wang, Self-microemulsion Technology for Water-insoluble Drug Delivery, Current Nanoscience 15(6) (2019) 576- 588. ## [142] S.M. Dizaj, F. Lotfpour, M. Barzegar-Jalali, M.-H. Zarrintan, K. Adibkia, Physicochemical characterization and antimicrobial evaluation of gentamicin-loaded CaCO 3 nanoparticles prepared via microemulsion method, Journal of Drug Delivery Science and Technology 35 (2016) 16-23.F. Niazvanda et al. / Journal of Composites and Compounds 2 (2020) 193-204 203 ## [143] M.N. Kelchen, N.K. Brogden, In vitro skin retention and drug permeation through intact and microneedle pretreated skin after application of propranolol loaded microemulsions, Pharmaceutical research 35(12) (2018) 228. ## [144] L. Huang, J. Wu, M. Liu, L. Mao, H. Huang, Q. Wan, Y. Dai, Y. Wen, X. Zhang, Y. Wei, Direct surface grafting of mesoporous silica nanoparticles with phospholipid choline-containing copolymers through chain transfer free radical polymerization and their controlled drug delivery, Journal of colloid and interface science 508 (2017) 396-404. ## [145] L.J. Min, T.Y.S. Edgar, Z. Zicheng, Y.W. Yee, Chapter 6 - Biomaterials for Bioprinting, in: L.G. Zhang, J.P. Fisher, K.W. Leong (Eds.), 3D Bioprinting and Nanotechnology in Tissue Engineering and Regenerative Medicine, Academic Press2015, pp. 129-148. ## [146] Z. Shi, C. Yang, R. Li, L. Ruan, Microwave thermal-triggered drug delivery using thermosensitive peptide-coated core–shell mesoporous silica nanoparticles, Journal of Materials Science 55(14) (2020) 6118-6129. ## [147] R.E. Mardziah, T.W. Wong, Eﬀects of microwave on drug-release responses of spray-dried alginate microspheres, Drug development and industrial pharmacy 36(10) (2010) 1149-1167. ## [148] T. Wong, Use of microwave in processing of drug delivery systems, Current Drug Delivery 5(2) (2008) 77-84. ## [149] H. Qiu, B. Cui, W. Zhao, P. Chen, H. Peng, Y. Wang, A novel microwave stimulus remote controlled anticancer drug release system based on Fe3O4@ZnO@ mGd 2O3: Eu@P(NIPAm-co-MAA) multifunctional nanocarriers, Journal of Materials Chemistry B 3(34) (2015) 6919-6927. ## [150] J. Xu, X. Cheng, L. Tan, C. Fu, M. Ahmed, J. Tian, J. Dou, Q. Zhou, X. Ren, Q. Wu, Microwave responsive nanoplatform via P-selectin mediated drug delivery for treatment of hepatocellular carcinoma with distant metastasis, Nano letters 19(5) (2019) 2914-2927. ## [151] S. Miyazaki, H. Aoyama, N. Kawasaki, W. Kubo, D. Attwood, In situ-gelling gellan formulations as vehicles for oral drug delivery, Journal of Controlled release 60(2-3) (1999) 287-295. ## [152] Y. Wu, Y. Liu, X. Li, D. Kebebe, B. Zhang, J. Ren, J. Lu, J. Li, S. Du, Z. Liu, Research progress of in-situ gelling ophthalmic drug delivery system, Asian Journal of Pharmaceutical Sciences 14(1) (2019) 1-15. ## [153] M. Agrawal, S. Saraf, S. Saraf, S.K. Dubey, A. Puri, U. Gupta, P. Kesharwani, V. Ravichandiran, P. Kumar, V. Naidu, Stimuli-responsive In situ gelling system for nose-to-brain drug delivery, Journal of Controlled Release (2020). ## [154] K. Itoh, T. Hirayama, A. Takahashi, W. Kubo, S. Miyazaki, M. Dairaku, M. Togashi, R. Mikami, D. Attwood, In situ gelling pectin formulations for oral drug delivery at high gastric pH, International journal of pharmaceutics 335(1-2) (2007) 90-96. ## [155] T.N. Nimi, D.R. Manohar, An Overview on In-Situ Nasal Gel for Drug Delivery, Journal of Pharmaceutical Sciences and Research 11(7) (2019) 2585-2589. ## [156] S. Desai, S. Bolton, A ﬂoating controlled-release drug delivery system: in vitro-in vivo evaluation, Pharmaceutical research 10(9) (1993) 1321-1325. ## [157] Z. Shi, X. Chen, L. Zhang, S. Ding, X. Wang, Q. Lei, W. Fang, FA-PEG decorated MOF nanoparticles as a targeted drug delivery system for controlled release of an autophagy inhibitor, Biomaterials science 6(10) (2018) 2582-2590. ## [158] K. Neha, H.S. Nirmala, Insitu gelling system: A Review, J Drug Del and Therapeutics 4(4) (2014) 93-103. ## [159] P. Suradkar, R. Mishra, T. Nandgude, Overview on Trends in Development of Gastroretentive Drug Delivery System, Research Journal of Pharmacy and Technology 12(11) (2019) 5633-5640. ## [160] D. Bhowmik, R. Bhanot, D. Gautam, P. Rai, K. Kumar, Gastro Retentive Drug Delivery Systems-a Novel Approaches of Controlled Drug Delivery Systems, Research Journal of Science and Technology 10(2) (2018) 145-156. ## [161] S. Fredenberg, M. Wahlgren, M. Reslow, A. Axelsson, The mechanisms of drug release in poly (lactic-co-glycolic acid)-based drug delivery systems—a review, International journal of pharmaceutics 415(1-2) (2011) 34-52. ## [162] J. Panyam, V. Labhasetwar, Biodegradable nanoparticles for drug and gene delivery to cells and tissue, Advanced drug delivery reviews 55(3) (2003) 329-347. ## [163] Y. Ma, J.C. Pacan, Q. Wang, Y. Xu, X. Huang, A. Korenevsky, P.M. Sabour, Microencapsulation of bacteriophage Felix O1 into chitosan-alginate microspheres for oral delivery, Applied and environmental microbiology 74(15) (2008) 4799- 4805. ## [164] J. Trygg, E. Yildir, R. Kolakovic, N. Sandler, P. Fardim, Anionic cellulose beads for drug encapsulation and release, Cellulose 21(3) (2014) 1945-1955. ## [165] H. Bao, Y. Pan, Y. Ping, N.G. Sahoo, T. Wu, L. Li, J. Li, L.H. Gan, Chitosan‐ functionalized graphene oxide as a nanocarrier for drug and gene delivery, Small 7(11) (2011) 1569-1578. ## [166] S. Javanbakht, M. Pooresmaeil, H. Namazi, Green one-pot synthesis of carboxymethylcellulose/Zn-based metal-organic framework/graphene oxide bio-nanocomposite as a nanocarrier for drug delivery system, Carbohydrate Polymers 208 (2019) 294-301. ## [167] H.H.P. Duong, L.-Y.L. Yung, Synergistic co-delivery of doxorubicin and paclitaxel using multi-functional micelles for cancer treatment, International journal of pharmaceutics 454(1) (2013) 486-495. ## [168] F. Foroughi, S.A. Hassanzadeh-Tabrizi, A. Bigham, In situ microemulsion synthesis of hydroxyapatite-MgFe2O4 nanocomposite as a magnetic drug delivery system, Materials Science and Engineering: C 68 (2016) 774-779. ## [169] K. Drlica, Biology of bacterial deoxyribonucleic acid topoisomerases, Microbiological reviews 48(4) (1984) 273. ## [170] D. Pathania, D. Gupta, N. Kothiyal, G. Eldesoky, M. Naushad, Preparation of a novel chitosan-g-poly (acrylamide)/Zn nanocomposite hydrogel and its applications for controlled drug delivery of oﬂoxacin, International journal of biological macromolecules 84 (2016) 340-348. ## [171] S. Das, A. Chaudhury, K.Y. Ng, Preparation and evaluation of zinc-pectin-chitosan composite particles for drug delivery to the colon: role of chitosan in modifying in vitro and in vivo drug release, Int J Pharm 406(1-2) (2011) 11-20. ## [172] K. Kompany, E.H. Mirza, S. Hosseini, B. Pingguan-Murphy, I. Djordjevic, Polyoctanediol citrate–ZnO composite flms: Preparation, characterization and release kinetics of nanoparticles from polymer matrix, Materials Letters 126 (2014) 165-168. ## [173] A. Dodero, M. Alloisio, S. Vicini, M. Castellano, Preparation of composite alginate-based electrospun membranes loaded with ZnO nanoparticles, Carbohydrate polymers 227 (2020) 115371. ## [174] W. Artifon, S.M. Pasini, A. Valério, S.Y.G. González, S.M.d.A.G. Ulson, A.A.U. de Souza, Harsh environment resistant-antibacterial zinc oxide/Polyetherimide electrospun composite scaﬀolds, Materials Science and Engineering: C 103 (2019) 109859. ## [175] A. Bhattacharjee, M.K. Purkait, S. Gumma, Loading and release of doxorubicin hydrochloride from Iron (III) trimesate MOF and zinc oxide nanoparticle composites, Dalton Transactions (2020). ## [176] A.U. Kura, S.H.H. Al Ali, M.Z. Hussein, S. Fakurazi, P. Arulselvan, Development of a controlled-release anti-parkinsonian nanodelivery system using levodopa as the active agent, International Journal of Nanomedicine 8 (2013) 1103. ## [177] A. Seyfoori, S.A.S. Ebrahimi, S. Omidian, S.M. Naghib, Multifunctional magnetic ZnFe2O4-hydroxyapatite nanocomposite particles for local anti-cancer drug delivery and bacterial infection inhibition: An in vitro study, Journal of the Taiwan Institute of Chemical Engineers 96 (2019) 503-508. ## [178] A. Nigam, S.J. Pawar, Structural, magnetic, and antimicrobial properties of zinc doped magnesium ferrite for drug delivery applications, Ceramics International 46(4) (2020) 4058-4064. ## [179] Z. Neščáková, K. Zheng, L. Liverani, Q. Nawaz, D. Galusková, H. Kaňková, M. Michálek, D. Galusek, A.R. Boccaccini, Multifunctional zinc ion doped sol – gel derived mesoporous bioactive glass nanoparticles for biomedical applications, Bioactive Materials 4 (2019) 312-321. ## [180] V. Thangaraj, M. Yogapriya, K. Thirumalai, M. Swaminathan, A. Sundaramurthy, R. Nandhakumar, S. Suresh, E. Vakees, A. Araichimani, Sol–Gel Synthesis of Ce 4–xSr1+ xFe5–xZnxO14+δ ## [0≤ x≤ 0.45] Superparamagnetic Oxide Systems and Its Magnetic, Dielectric, and Drug Delivery Properties, ACS omega 3(12) (2018) 16509-16518. ## [181] D. Pathania, D. Gupta, N.C. Kothiyal, G. sharma, G.E. Eldesoky, M. Naushad, Preparation of a novel chitosan-g-poly(acrylamide)/Zn nanocomposite hydrogel and its applications for controlled drug delivery of oﬂoxacin, International Journal of Biological Macromolecules 84 (2016) 340-348. ## [182] M. Khatamian, B. Divband, F. Farahmand-Zahed, Synthesis and characterization of Zinc (II)-loaded Zeolite/Graphene oxide nanocomposite as a new drug carrier, Materials Science and Engineering: C 66 (2016) 251-258. ## [183] R. Rakhshaei, H. Namazi, H. Hamishehkar, H.S. Kafl, R. Salehi, In situ synthesized chitosan–gelatin/ZnO nanocomposite scaﬀold with drug delivery properties: Higher antibacterial and lower cytotoxicity eﬀects, Journal of Applied Polymer Science 136(22) (2019) 47590. ## [184] M. Yadollahi, S. Farhoudian, S. Barkhordari, I. Gholamali, H. Farhadnejad, H. Motasadizadeh, Facile synthesis of chitosan/ZnO bio-nanocomposite hydrogel beads as drug delivery systems, International journal of biological macromolecules 82 (2016) 273-278. ## [185] Z. Yang, L. Wang, Y. Liu, S. Liu, D. Tang, L. Meng, B. Cui, ZnO capped ﬂower-like porous carbon-Fe3O4 composite as carrier for bi-triggered drug delivery, Materials Science and Engineering: C 107 (2020) 110256. ## [186] F. Yang, X. Niu, X. Gu, C. Xu, W. Wang, Y. Fan, Biodegradable Magnesium-Incorporated Poly(l-lactic acid) Microspheres for Manipulation of Drug Release and Alleviation of Inﬂammatory Response, ACS Applied Materials and Interfaces 11(26) (2019) 23546-23557.204 F. Niazvand et al. / Journal of Composites and Compounds 2 (2020) 193-204 ## [187] M. Cheddadi, E. López-Cabarcos, K. Slowing, E. Barcia, A. Fernández-Carballido, Cytotoxicity and biocompatibility evaluation of a poly(magnesium acrylate) hydrogel synthesized for drug delivery, International Journal of Pharmaceutics 413(1) (2011) 126-133. ## [188] N.P. Rijal, U. Adhikari, N. Bhattarai, Magnesium Incorporated Polycaprolactone-Based Composite Nanofbers, ASME 2015 International Mechanical Engineering Congress and Exposition, 2015. ## [189] N.P. Rijal, U. Adhikari, S. Khanal, D. Pai, J. Sankar, N. Bhattarai, Magnesium oxide-poly(ε-caprolactone)-chitosan-based composite nanofber for tissue engineering applications, Materials Science and Engineering: B 228 (2018) 18-27. ## [190] F. Mohammad, T. Arfn, H.A. Al-Lohedan, Sustained drug release and electrochemical performance of ethyl cellulose-magnesium hydrogen phosphate composite, Materials Science and Engineering: C 71 (2017) 735-743. ## [191] F. Foroughi, S. Hassanzadeh-Tabrizi, A. Bigham, In situ microemulsion synthesis of hydroxyapatite-MgFe2O4 nanocomposite as a magnetic drug delivery system, Materials Science and Engineering: C 68 (2016) 774-779. ## [192] Z. Tabia, K. El Mabrouk, M. Bricha, K. Nouneh, Mesoporous bioactive glass nanoparticles doped with magnesium: drug delivery and acellular in vitro bioactivity, RSC advances 9(22) (2019) 12232-12246.200 F. Niazvand et al. / Journal of Composites and Compounds 2 (2020) 193-204 Carbohydrate polymers 150 (2016) 330-352. ## [8] F. Sharifanjazi, A.H. Pakseresht, M.S. Asl, A. Esmaeilkhanian, H.W. Jang, M. Shokouhimehr, Hydroxyapatite consolidated by zirconia: applications for dental implant, Journal of Composites and Compounds 2(1) (2020) 26-34. ## [9] L. Bazli, B. Eftekhari Yekta, A. Khavandi, Preparation and Characterization of Sn-Containing Glasses for Brachytherapy Applications, Transactions of the Indian Ceramic Society 76(4) (2017) 242-246. ## [10] Y. Kameshima, H. Sasaki, T. Isobe, A. Nakajima, K. Okada, Synthesis of composites of sodium oleate/Mg–Al-ascorbic acid-layered double hydroxides for drug delivery applications, International journal of pharmaceutics 381(1) (2009) 34-39. ## [11] M. Abniki, A. Moghimi, F. Azizinejad, Fabrication of bionanocomposite based on LDH using biopolymer of gum arabic and chitosan-coating for sustained drug-release, Journal of the Serbian Chemical Society 85(5) (2020). ## [12] M. Abniki, A. Moghimi, F. Azizinejad, Synthesis of calcium‐layered double hydroxide based nanohybrid for controlled release of an anti‐inﬂammatory drug, Journal of the Chinese Chemical Society (2020). ## [13] W.-H. Lu, K.-D. Li, C.-H. Lu, L.G. Teoh, W.H. Wu, Y.C. Shen, Synthesis and characterization of mesoporous SiO2–CaO–P2O5 bioactive glass by sol–gel process, Materials transactions 54(5) (2013) 791-795. ## [14] J. Andersson, S. Areva, B. Spliethoﬀ, M. Lindén, Sol–gel synthesis of a multifunctional, hierarchically porous silica/apatite composite, Biomaterials 26(34) (2005) 6827-6835. ## [15] S.P. Hudson, R.F. Padera, R. Langer, D.S. Kohane, The biocompatibility of mesoporous silicates, Biomaterials 29(30) (2008) 4045-4055. ## [16] X. Li, X. Wang, H. Chen, P. Jiang, X. Dong, J. Shi, Hierarchically porous bioactive glass scaﬀolds synthesized with a PUF and P123 cotemplated approach, Chemistry of Materials 19(17) (2007) 4322-4326. ## [17] A. López-Noriega, D. Arcos, I. Izquierdo-Barba, Y. Sakamoto, O. Terasaki, M. Vallet-Regí, Ordered mesoporous bioactive glasses for bone tissue regeneration, Chemistry of Materials 18(13) (2006) 3137-3144. ## [18] X. Yan, X. Huang, C. Yu, H. Deng, Y. Wang, Z. Zhang, S. Qiao, G. Lu, D. Zhao, The in-vitro bioactivity of mesoporous bioactive glasses, Biomaterials 27(18) (2006) 3396-3403. ## [19] X. Yan, C. Yu, X. Zhou, J. Tang, D. Zhao, Highly ordered mesoporous bioactive glasses with superior in vitro bone‐forming bioactivities, Angewandte Chemie International Edition 43(44) (2004) 5980-5984. ## [20] M. Vašák, D.W. Hasler, Metallothioneins: new functional and structural insights, Current opinion in chemical biology 4(2) (2000) 177-183. ## [21] M.F. Heragh, S. Eskandarinezhad, A. Dehghan, Ni-Cu matrix composite reinforced with CNTs: preparation, characterization, wear and corrosion behavior, inhibitory eﬀects, Journal of Composites and Compounds 2(4) (2020) 123-128. ## [22] C.T. Chasapis, A.C. Loutsidou, C.A. Spiliopoulou, M.E. Stefanidou, Zinc and human health: an update, Archives of toxicology 86(4) (2012) 521-534. ## [23] E. Alhava, H. Olkkonen, J. Puittinen, V. Nokso-Koivisto, Zinc content of human cancellous bone, Acta Orthopaedica Scandinavica 48(1) (1977) 1-4. ## [24] H. Kim, S. Mondal, S. Bharathiraja, P. Manivasagan, M.S. Moorthy, J. Oh, Optimized Zn-doped hydroxyapatite/doxorubicin bioceramics system for efcient drug delivery and tissue engineering application, Ceramics International 44(6) (2018) 6062-6071. ## [25] Y. Su, I. Cockerill, Y. Wang, Y.-X. Qin, L. Chang, Y. Zheng, D. Zhu, Zincbased biomaterials for regeneration and therapy, Trends in biotechnology 37(4) (2019) 428-441. ## [26] Z. Gao, D. Zhang, X. Li, S. Jiang, Q. Zhang, Current status, opportunities and challenges in chemical conversion coatings for zinc, Colloids and Surfaces A: Physicochemical and Engineering Aspects 546 (2018) 221-236. ## [27] S. Parveen, R. Misra, S.K. Sahoo, Nanoparticles: a boon to drug delivery, therapeutics, diagnostics and imaging, Nanomedicine: Nanotechnology, Biology and Medicine 8(2) (2012) 147-166. ## [28] H.M. Xiong, ZnO nanoparticles applied to bioimaging and drug delivery, Advanced Materials 25(37) (2013) 5329-5335. ## [29] Z.Y. Zhang, Y.D. Xu, Y.Y. Ma, L.L. Qiu, Y. Wang, J.L. Kong, H.M. Xiong, Biodegradable ZnO@ polymer core–shell nanocarriers: pH‐triggered release of doxorubicin in vitro, Angewandte Chemie 125(15) (2013) 4221-4225. ## [30] G. Song, Control of biodegradation of biocompatable magnesium alloys, Corrosion science 49(4) (2007) 1696-1701. ## [31] A.H. Shahbaz, M. Esmaeilian, R. NasrAzadani, K. Gavanji, The eﬀect of MgF2 addition on the mechanical properties of hydroxyapatite synthesized via powder metallurgy, Journal of Composites and Compounds 1(1) (2019) 18-24. ## [32] S. Nasibi, K. Alimohammadi, L. Bazli, S. Eskandarinezhad, A. Mohammadi, N. Sheysi, TZNT alloy for surgical implant applications: A systematic review, Journal of Composites and Compounds 2(3) (2020) 62-68. ## [33] R. Erbel, C. Di Mario, J. Bartunek, J. Bonnier, B. de Bruyne, F.R. Eberli, P. Erne, M. Haude, B. Heublein, M. Horrigan, Temporary scaﬀolding of coronary arteries with bioabsorbable magnesium stents: a prospective, non-randomised multicentre trial, The Lancet 369(9576) (2007) 1869-1875. ## [34] M. Haude, R. Erbel, P. Erne, S. Verheye, H. Degen, D. Böse, P. Vermeersch, I. Wijnbergen, N. Weissman, F. Prati, Safety and performance of the drug-eluting absorbable metal scaﬀold (DREAMS) in patients with de-novo coronary lesions: 12 month results of the prospective, multicentre, frst-in-man BIOSOLVE-I trial, The Lancet 381(9869) (2013) 836-844. ## [35] M. Haude, H. Ince, A. Abizaid, R. Toelg, P.A. Lemos, C. von Birgelen, E.H. Christiansen, W. Wijns, F.-J. Neumann, C. Kaiser, Safety and performance of the second-generation drug-eluting absorbable metal scaﬀold in patients with de-novo coronary artery lesions (BIOSOLVE-II): 6 month results of a prospective, multicentre, non-randomised, frst-in-man trial, The Lancet 387(10013) (2016) 31-39. ## [36] B. Heublein, R. Rohde, V. Kaese, M. Niemeyer, W. Hartung, A. Haverich, Biocorrosion of magnesium alloys: a new principle in cardiovascular implant technology?, Heart 89(6) (2003) 651-656. ## [37] H. Li, H. Zhong, K. Xu, K. Yang, J. Liu, B. Zhang, F. Zheng, Y. Xia, L. Tan, D. Hong, Enhanced efcacy of sirolimus-eluting bioabsorbable magnesium alloy stents in the prevention of restenosis, Journal of Endovascular Therapy 18(3) (2011) 407-415. ## [38] R. Waksman, R. Erbel, C. Di Mario, J. Bartunek, B. de Bruyne, F.R. Eberli, P. Erne, M. Haude, M. Horrigan, C. Ilsley, Early-and long-term intravascular ultrasound and angiographic fndings after bioabsorbable magnesium stent implantation in human coronary arteries, JACC: Cardiovascular Interventions 2(4) (2009) 312-320. ## [39] R. Waksman, R. Pakala, P.K. Kuchulakanti, R. Baﬀour, D. Hellinga, R. Seabron, F.O. Tio, E. Wittchow, S. Hartwig, C. Harder, Safety and efcacy of bioabsorbable magnesium alloy stents in porcine coronary arteries, Catheterization and Cardiovascular Interventions 68(4) (2006) 607-617. ## [40] E. Wittchow, N. Adden, J. Riedmüller, C. Savard, R. Waksman, M. Braune, Bioresorbable drug-eluting magnesium-alloy scaﬀold: design and feasibility in a porcine coronary model, EuroIntervention 8(12) (2013) 1441-1450. ## [41] P. Zartner, R. Cesnjevar, H. Singer, M. Weyand, First successful implantation of a biodegradable metal stent into the left pulmonary artery of a preterm baby, Catheterization and Cardiovascular Interventions 66(4) (2005) 590-594. ## [42] M. Haude, H. Ince, A. Abizaid, R. Toelg, P.A. Lemos, C. von Birgelen, E.H. Christiansen, W. Wijns, F.-J. Neumann, C. Kaiser, Sustained safety and performance of the second-generation drug-eluting absorbable metal scaﬀold in patients with de novo coronary lesions: 12-month clinical results and angiographic fndings of the BIOSOLVE-II frst-in-man trial, European heart journal 37(35) (2016) 2701-2709. ## [43] M. Diba, O.-M. Goudouri, F. Tapia, A.R. Boccaccini, Magnesium-containing bioactive polycrystalline silicate-based ceramics and glass-ceramics for biomedical applications, Current opinion in solid state and materials science 18(3) (2014) 147-167. ## [44] Y. Bi, Y. Zheng, Y. Li, Microstructure and mechanical properties of sintered porous magnesium using polymethyl methacrylate as the space holder, Materials Letters 161 (2015) 583-586. ## [45] H. Bakhsheshi-Rad, E. Hamzah, M.P. Staiger, G.J. Dias, Z. Hadisi, M. Saheban, M. Kashefan, Drug release, cytocompatibility, bioactivity, and antibacterial activity of doxycycline loaded Mg-Ca-TiO2 composite scaﬀold, Materials and Design 139 (2018) 212-221. ## [46] K.K. Jain, Drug delivery systems-an overview, Drug delivery systems, Springer2008, pp. 1-50. ## [47] M. Arefan, M. Hojjati, I. Tajzad, A. Mokhtarzade, M. Mazhar, A. Jamavari, A review of Polyvinyl alcohol/Carboxiy methyl cellulose (PVA/CMC) composites for various applications, Journal of Composites and Compounds 2(3) (2020) 69- 76. ## [48] P. Abasian, M. Radmansouri, M.H. Jouybari, M.V. Ghasemi, A. Mohammadi, M. Irani, F.S. Jazi, Incorporation of magnetic NaX zeolite/DOX into the PLA/chitosan nanofbers for sustained release of doxorubicin against carcinoma cells death in vitro, International journal of biological macromolecules 121 (2019) 398-406. ## [49] H. Derendorf, L.J. Lesko, P. Chaikin, W.A. Colburn, P. Lee, R. Miller, R. Powell, G. Rhodes, D. Stanski, J. Venitz, Pharmacokinetic/pharmacodynamic modeling in drug research and development, The Journal of Clinical Pharmacology 40(12) (2000) 1399-1418. ## [50] S. Gopi, A. Amalraj, N.P. Sukumaran, J.T. Haponiuk, S. Thomas, Biopolymers and their composites for drug delivery: a brief review, Macromolecular Symposia, Wiley Online Library, 2018, p. 1800114. ## [51] G.R. Matzke, G.R. Aronoﬀ, A.J. Atkinson Jr, W.M. Bennett, B.S. Decker, K.-U. Eckardt, T. Golper, D.W. Grabe, B. Kasiske, F. Keller, Drug dosing consideration in patients with acute and chronic kidney disease—a clinical update fromF. Niazvanda et al. / Journal of Composites and Compounds 2 (2020) 193-204 201 Kidney Disease: Improving Global Outcomes (KDIGO), Kidney international 80(11) (2011) 1122-1137. ## [52] M.J. Munoz-Davila, Role of old antibiotics in the era of antibiotic resistance. Highlighted nitrofurantoin for the treatment of lower urinary tract infections, Antibiotics 3(1) (2014) 39-48. ## [53] J.J. De Waele, S. Carrette, M. Carlier, V. Stove, J. Boelens, G. Claeys, I. Leroux-Roels, E. Hoste, P. Depuydt, J. Decruyenaere, Therapeutic drug monitoring-based dose optimisation of piperacillin and meropenem: a randomised controlled trial, Intensive care medicine 40(3) (2014) 380-387. ## [54] S.K. Bardal, J.E. Waechter, D.S. Martin, Applied pharmacology, Elsevier Health Sciences2011. ## [55] W. Brand, M.E. Schutte, G. Williamson, J.J. van Zanden, N.H. Cnubben, J.P. Groten, P.J. van Bladeren, I.M. Rietjens, Flavonoid-mediated inhibition of intestinal ABC transporters may aﬀect the oral bioavailability of drugs, food-borne toxic compounds and bioactive ingredients, Biomedicine and pharmacotherapy 60(9) (2006) 508-519. ## [56] A.H. Chow, H.H. Tong, P. Chattopadhyay, B.Y. Shekunov, Particle engineering for pulmonary drug delivery, Pharmaceutical research 24(3) (2007) 411-437. ## [57] S. Amirhossein, A.-B. Aydin, Z. Habib, Polaroid-PET: a PET scanner with detectors ftted with polaroids for fltering unpolarized optical photons: a Monte Carlo simulation study, Physics in Medicine and Biology (2020). ## [58] A. Sanaat, H. Zaidi, Depth of interaction estimation in a preclinical PET scanner equipped with monolithic crystals coupled to SiPMs using a deep neural network, Applied Sciences 10(14) (2020) 4753. ## [59] A. Sanaat, H. Arabi, M.R. Ay, H. Zaidi, Novel preclinical PET geometrical concept using a monolithic scintillator crystal oﬀering concurrent enhancement in spatial resolution and detection sensitivity: a simulation study, Physics in Medicine and Biology 65(4) (2020) 045013. ## [60] A. Sanaat, H. Arabi, I. Mainta, V. Garibotto, H. Zaidi, Projection-space implementation of deep learning-guided low-dose brain PET imaging improves performance over implementation in image-space, Journal of Nuclear Medicine (2020) jnumed. 119.239327. ## [61] N. Kamaly, B. Yameen, J. Wu, O.C. Farokhzad, Degradable controlled-release polymers and polymeric nanoparticles: mechanisms of controlling drug release, Chemical reviews 116(4) (2016) 2602-2663. ## [62] J. Daraei, Production and characterization of PCL (Polycaprolactone) coated TCP/nanoBG composite scaﬀolds by sponge foam method for orthopedic applications, Journal of Composites and Compounds 2(1) (2020) 45-50. ## [63] X. Huang, S. Wu, X. Ke, X. Li, X. Du, Phosphonated pillar ## [5] arene-valved mesoporous silica drug delivery systems, ACS Applied Materials and Interfaces 9(23) (2017) 19638-19645. ## [64] N.G. Kotla, B. Chandrasekar, P. Rooney, G. Sivaraman, A. Larrañaga, K.V. Krishna, A. Pandit, Y. Rochev, Biomimetic lipid-based nanosystems for enhanced dermal delivery of drugs and bioactive agents, ACS Biomaterials Science and Engineering 3(7) (2017) 1262-1272. ## [65] A. Kazemzadeh, H. Kazemzadeh, Determination of Hg2+ by Diphenylcarbazone Compound in Polymer Film, Journal of Composites and Compounds 1(1) (2019) 30-35. ## [66] A. Nouri, B. Faraji Dizaji, N. Kianinejad, A. Jafari Rad, S. Rahimi, M. Irani, F. Sharifan Jazi, Simultaneous linear release of folic acid and doxorubicin from ethyl cellulose/chitosan/g‐C3N4/MoS2 core‐shell nanofbers and its anticancer properties, Journal of Biomedical Materials Research Part A (2020). ## [67] D. Liu, F. Yang, F. Xiong, N. Gu, The smart drug delivery system and its clinical potential, Theranostics 6(9) (2016) 1306. ## [68] Z. Wang, Y. Duan, Y. Duan, Application of polydopamine in tumor targeted drug delivery system and its drug release behavior, Journal of Controlled Release 290 (2018) 56-74. ## [69] J. Ma, N. Zhao, D. Zhu, Endothelial cellular responses to biodegradable metal zinc, ACS biomaterials science and engineering 1(11) (2015) 1174-1182. ## [70] F.S. Jazi, N. Parvin, M. Rabiei, M. Tahriri, Z.M. Shabestari, A.R. Azadmehr, Eﬀect of the synthesis route on the grain size and morphology of ZnO/Ag nanocomposite, Journal of Ceramic Processing Research 13(5) (2012) 523-526. ## [71] J. Jiang, J. Pi, J. Cai, The advancing of zinc oxide nanoparticles for biomedical applications, Bioinorganic chemistry and applications 2018 (2018). ## [72] Z. Zeng, X. Fang, W. Miao, Y. Liu, T. Maiyalagan, S. Mao, Electrochemically Sensing of Trichloroacetic Acid with Iron(II) Phthalocyanine and Zn-Based Metal Organic Framework Nanocomposites, ACS Sensors 4(7) (2019) 1934-1941. ## [73] W. Liu, Y. Pan, W. Xiao, H. Xu, D. Liu, F. Ren, X. Peng, J. Liu, Recent developments on zinc (ii) metal–organic framework nanocarriers for physiological pH-responsive drug delivery, MedChemComm 10(12) (2019) 2038-2051. ## [74] K. Dong, Y. Zhang, L. Zhang, Z. Wang, J. Ren, X. Qu, Facile preparation of metal− organic frameworks-based hydrophobic anticancer drug delivery nanoplatform for targeted and enhanced cancer treatment, Talanta 194 (2019) 703-708. ## [75] M. Zamani, M. Rostami, M. Aghajanzadeh, H. Kheiri Manjili, K. Rostamizadeh, H. Danafar, Mesoporous titanium dioxide@ zinc oxide–graphene oxide nanocarriers for colon-specifc drug delivery, Journal of Materials Science 53(3) (2018) 1634-1645. ## [76] J.W. Rasmussen, E. Martinez, P. Louka, D.G. Wingett, Zinc oxide nanoparticles for selective destruction of tumor cells and potential for drug delivery applications, Expert opinion on drug delivery 7(9) (2010) 1063-1077. ## [77] V. Karpina, V. Lazorenko, C. Lashkarev, V. Dobrowolski, L. Kopylova, V. Baturin, S. Pustovoytov, A.J. Karpenko, S. Eremin, P. Lytvyn, Zinc oxide–analogue of GaN with new perspective possibilities, Crystal Research and Technology: Journal of Experimental and Industrial Crystallography 39(11) (2004) 980-992. ## [78] X. Huang, X. Zheng, Z. Xu, C. Yi, Zno-based nanocarriers for drug delivery application: From passive to smart strategies, International journal of pharmaceutics 534(1-2) (2017) 190-194. ## [79] A.J. Rad, Synthesis of copper oxide nanoparticles on activated carbon for pollutant removal in Tartrazine structure, Journal of Composites and Compounds 2(3) (2020) 99-104. ## [80] A. Moghanian, A. Ghorbanoghli, M. Kazem‐Rostami, A. Pazhouheshgar, E. Salari, M. Saghaf Yazdi, T. Alimardani, H. Jahani, F. Sharifan Jazi, M. Tahriri, Novel antibacterial Cu/Mg‐substituted 58S‐bioglass: Synthesis, characterization and investigation of in vitro bioactivity, International Journal of Applied Glass Science 11(4) (2020) 685-698. ## [81] F. Sharifanjazi, M. Moradi, A. Abouchenari, A.H. Pakseresht, A. Esmaeilkhanian, M. Shokouhimehr, M.S. Asl, Eﬀects of Sr and Mg dopants on biological and mechanical properties of SiO2–CaO–P2O5 bioactive glass, Ceramics International (2020). ## [82] S. Ni, L. Chou, J. Chang, Preparation and characterization of forsterite (Mg- 2SiO4) bioceramics, Ceramics International 33(1) (2007) 83-88. ## [83] N. Sezer, Z. Evis, S.M. Kayhan, A. Tahmasebifar, M. Koç, Review of magnesium-based biomaterials and their applications, Journal of Magnesium and Alloys 6(1) (2018) 23-43. ## [84] A. Bordbar-Khiabani, B. Yarmand, M. Mozafari, Emerging magnesium-based biomaterials for orthopedic implantation, Thomas Telford Ltd, 2019. ## [85] Z. Wu, T. Tang, H. Guo, S. Tang, Y. Niu, J. Zhang, W. Zhang, R. Ma, J. Su, C. Liu, In vitro degradability, bioactivity and cell responses to mesoporous magnesium silicate for the induction of bone regeneration, Colloids and Surfaces B: Biointerfaces 120 (2014) 38-46. ## [86] A. Bigham, S.A. Hassanzadeh-Tabrizi, M. Rafenia, H. Salehi, Ordered mesoporous magnesium silicate with uniform nanochannels as a drug delivery system: The eﬀect of calcination temperature on drug delivery rate, Ceramics International 42(15) (2016) 17185-17191. ## [87] M. Vallet-Regi, Bio-ceramics with clinical applications, John Wiley and Sons2014. ## [88] P. Wu, D.W. Grainger, Drug/device combinations for local drug therapies and infection prophylaxis, Biomaterials 27(11) (2006) 2450-2467. ## [89] H. Dong, Q. Li, C. Tan, N. Bai, P. Cai, Bi-directional controlled release of ibuprofen and Mg2+ from magnesium alloys coated by multifunctional composite, Materials Science and Engineering: C 68 (2016) 512-518. ## [90] J. Tian, S. Shen, C. Zhou, X. Dang, Y. Jiao, L. Li, S. Ding, H. Li, Investigation of the antimicrobial activity and biocompatibility of magnesium alloy coated with HA and antimicrobial peptide, Journal of Materials Science: Materials in Medicine 26(2) (2015) 66. ## [91] J. Zhang, Z. Wen, M. Zhao, G. Li, C. Dai, Eﬀect of the addition CNTs on performance of CaP/chitosan/coating deposited on magnesium alloy by electrophoretic deposition, Materials Science and Engineering: C 58 (2016) 992-1000. ## [92] A. Morawska-Chochół, P. Domalik-Pyzik, J. Chłopek, B. Szaraniec, J. Sterna, M. Rzewuska, M. Boguń, R. Kucharski, P. Mielczarek, Gentamicin release from biodegradable poly-l-lactide based composites for novel intramedullary nails, Materials Science and Engineering: C 45 (2014) 15-20. ## [93] A. Kazemzadeh, M.A. Meshkat, H. Kazemzadeh, M. Moradi, R. Bahrami, R. Pouriamanesh, Preparation of graphene nanolayers through surfactant-assisted pure shear milling method, Journal of Composites and Compounds 1(1) (2019) 25-30. ## [94] W.E. Teo, S. Ramakrishna, A review on electrospinning design and nanofbre assemblies, Nanotechnology 17(14) (2006) R89. ## [95] L.A. Mercante, V.P. Scagion, F.L. Migliorini, L.H. Mattoso, D.S. Correa, Electrospinning-based (bio) sensors for food and agricultural applications: A review, TrAC Trends in Analytical Chemistry 91 (2017) 91-103. ## [96] M. Jiménez, C. Abradelo, J. San Román, L. Rojo, Bibliographic review on the state of the art of strontium and zinc based regenerative therapies. Recent developments and clinical applications, Journal of materials chemistry B 7(12) (2019)202 F. Niazvand et al. / Journal of Composites and Compounds 2 (2020) 193-204 1974-1985. ## [97] T.J. Sill, H.A. Von Recum, Electrospinning: applications in drug delivery and tissue engineering, Biomaterials 29(13) (2008) 1989-2006. ## [98] Y. Qian, Solvothermal Synthesis of Nanocrystalline III–V Semiconductors, Advanced Materials 11(13) (1999) 1101-1102. ## [99] C. Wang, Z.-X. Deng, Y. Li, The synthesis of nanocrystalline anatase and rutile titania in mixed organic media, Inorganic Chemistry 40(20) (2001) 5210-5214. ## [100] K. Kaviyarasu, E. Manikandan, P. Paulraj, S. Mohamed, J. Kennedy, One dimensional well-aligned CdO nanocrystal by solvothermal method, Journal of alloys and compounds 593 (2014) 67-70. ## [101] C.-S. Kim, B.K. Moon, J.-H. Park, S. Tae Chung, S.-M. Son, Synthesis of nanocrystalline TiO2 in toluene by a solvothermal route, Journal of Crystal Growth 254(3) (2003) 405-410. ## [102] M. Kang, Synthesis of Fe/TiO2 photocatalyst with nanometer size by solvothermal method and the eﬀect of H 2O addition on structural stability and photodecomposition of methanol, Journal of Molecular Catalysis A: Chemical 197(1) (2003) 173-183. ## [103] S. Yin, Y. Fujishiro, J. Wu, M. Aki, T. Sato, Synthesis and photocatalytic properties of fbrous titania by solvothermal reactions, Journal of Materials Processing Technology 137(1-3) (2003) 45-48. ## [104] S.M. Gupta, M. Tripathi, A review on the synthesis of TiO2 nanoparticles by solution route, Central European Journal of Chemistry 10(2) (2012) 279-294. ## [105] F.L. Theiss, G.A. Ayoko, R.L. Frost, Synthesis of layered double hydroxides containing Mg2+, Zn2+, Ca2+ and Al3+ layer cations by co-precipitation methods—A review, Applied Surface Science 383 (2016) 200-213. ## [106] M. Bukhtiyarova, A review on eﬀect of synthesis conditions on the formation of layered double hydroxides, Journal of Solid State Chemistry 269 (2019) 494-506. ## [107] V. Solovov, N. Nikolenko, V. Kovalenko, V. Kotok, A. Burkov, D. Kondrat’ev, O. Chernovа, S. Zhukovin, Synthesis of Ni (II)-Ti (IV) layered double hydroxides using coprecipitation at high supersaturation method, ARPN Journal of Engineering and Applied Sciences 13(24) (2018) 9652-9656. ## [108] X. Duan, D.G. Evans, Layered double hydroxides, Springer Science and Business Media2006. ## [109] H.W. Olfs, L.O. Torres-Dorante, R. Eckelt, H. Kosslick, Comparison of different synthesis routes for Mg–Al layered double hydroxides (LDH): Characterization of the structural phases and anion exchange properties, Applied Clay Science 43(3) (2009) 459-464. ## [110] L. Bazli, M. Siavashi, A. Shiravi, A review of carbon nanotube/TiO2 composite prepared via sol-gel method, Journal of Composites and Compounds 1(1) (2019) 1-9. ## [111] A. Bakhtiari, A. Cheshmi, M. Naeimi, S.M. Fathabad, M. Aliasghari, A.M. Chahardehi, S. Hassani, V. Elhami, Synthesis and characterization of the novel 80S bioactive glass: bioactivity,‎ biocompatibility, cytotoxicity, Journal of Composites and Compounds 2(4) (2020) 110-114. ## [112] L. Armelao, D. Barreca, M. Bertapelle, G. Bottaro, C. Sada, E. Tondello, A sol–gel approach to nanophasic copper oxide thin flms, Thin Solid Films 442(1) (2003) 48-52. ## [113] F.S. Jazi, N. Parvin, M. Tahriri, M. Alizadeh, S. Abedini, M. Alizadeh, The relationship between the synthesis and morphology of SnO2-Ag2O nanocomposite, Synthesis and Reactivity in Inorganic, Metal-Organic, and Nano-Metal Chemistry 44(5) (2014) 759-764. ## [114] M. Alizadeh, F. Sharifanjazi, E. Haghshenasjazi, M. Aghakhani, L. Rajabi, Production of nanosized boron oxide powder by high-energy ball milling, Synthesis and Reactivity in Inorganic, Metal-Organic, and Nano-Metal Chemistry 45(1) (2015) 11-14. ## [115] L.S. Cividanes, T.M. Campos, L.A. Rodrigues, D.D. Brunelli, G.P. Thim, Review of mullite synthesis routes by sol–gel method, Journal of Sol-Gel Science and Technology 55(1) (2010) 111-125. ## [116] M. Gonçalves, Sol-gel silica nanoparticles in medicine: A natural choice. Design, synthesis and products, Molecules 23(8) (2018) 2021. ## [117] S. Devaraju, K. Krishnadevi, E. Naveena, M. Alagar, Eco-friendly fully bio-based polybenzoxazine-silica hybrid materials by sol–gel approach, Polymer Bulletin (2020) 1-10. ## [118] H. Böttcher, P. Slowik, W. Süß, Sol-gel carrier systems for controlled drug delivery, Journal of sol-gel science and technology 13(1-3) (1998) 277-281. ## [119] M. Catauro, E. Tranquillo, F. Barrino, I. Blanco, F. Dal Poggetto, D. Naviglio, Drug release of hybrid materials containing Fe (II) citrate synthesized by sol-gel technique, Materials 11(11) (2018) 2270. ## [120] Y. Ding, W. Li, A. Correia, Y. Yang, K. Zheng, D. Liu, D.W. Schubert, A.R. Boccaccini, H.A. Santos, J.A. Roether, Electrospun polyhydroxybutyrate/poly (ε-caprolactone)/Sol–gel-derived silica hybrid scaﬀolds with drug releasing function for bone tissue engineering applications, ACS applied materials and interfaces 10(17) (2018) 14540-14548. ## [121] M. Catauro, F. Barrino, G. Dal Poggetto, M. Milazzo, I. Blanco, S.V. Ciprioti, Structure, drug absorption, bioactive and antibacterial properties of sol-gel SiO2/ ZrO 2 materials, Ceramics International (2020). ## [122] S.K. Sahoo, S. Barik, G. Dehury, S. Dhala, S. Kanungo, B.B. Barik, K.K. Puhan, Evaluation of controlled release theophylline microspheres prepared with cellulose acetate using solvent evaporation method, Tropical Journal of Pharmaceutical Research 10(2) (2011). ## [123] S. Jaraswekin, S. Prakongpan, R. Bodmeier, Eﬀect of poly (lactide-co-glycolide) molecular weight on the release of dexamethasone sodium phosphate from microparticles, Journal of microencapsulation 24(2) (2007) 117-128. ## [124] S. Freitas, H.P. Merkle, B. Gander, Microencapsulation by solvent extraction/evaporation: reviewing the state of the art of microsphere preparation process technology, Journal of Controlled Release 102(2) (2005) 313-332. ## [125] J. Emami, H. Hamishehkar, A.R. Najafabadi, K. Gilani, M. Minaiyan, H. Mahdavi, A. Nokhodchi, A Novel Approach to Prepare Insulin-Loaded Poly (Lactic-Co-Glycolic Acid) Microcapsules and the Protein Stability Study, Journal of Pharmaceutical Sciences 98(5) (2009) 1712-1731. ## [126] M.L. Manca, Chitosan and PLGA microspheres as drug delivery system against pulmonary mycobacteria infections, (2007). ## [127] M. Hoppel, D. Mahrhauser, C. Stallinger, F. Wagner, M. Wirth, C. Valenta, Natural polymer‐stabilized multiple water‐in‐oil‐in‐water emulsions: a novel dermal drug delivery system for 5‐ﬂuorouracil, Journal of Pharmacy and Pharmacology 66(5) (2014) 658-667. ## [128] H. Yang, Y. Hao, Q. Liu, Z. Mi, Z. Wang, L. Zhu, Q. Feng, N. Hu, Preparation and in vitro study of hydrochloric norvancomycin encapsulated poly (d, l-lactide-co-glycolide, PLGA) microspheres for potential use in osteomyelitis, Artifcial cells, nanomedicine, and biotechnology 45(7) (2017) 1326-1330. ## [129] M. Li, O. Rouaud, D. Poncelet, Microencapsulation by solvent evaporation: State of the art for process engineering approaches, International Journal of Pharmaceutics 363(1) (2008) 26-39. ## [130] W.M. Obeidat, Recent patents review in microencapsulation of pharmaceuticals using the emulsion solvent removal methods, Recent patents on drug delivery and formulation 3(3) (2009) 178-192. ## [131] Y. Maa, C. Hsu, Eﬀect of primary emulsions on microsphere size and protein-loading in the double emulsion process, Journal of microencapsulation 14(2) (1997) 225-241. ## [132] D. Noviendri, Microencapsulation of Fucoxanthin by Water-in-Oil-in-Water (W/O/W) Double Emulsion Solvent Evaporation Method: A Review, Squalen Bulletin of Marine and Fisheries Postharvest and Biotechnology 9(3) (2014). ## [133] Y.-Y. Yang, T.-S. Chung, N.P. Ng, Morphology, drug distribution, and in vitro release profles of biodegradable polymeric microspheres containing protein fabricated by double-emulsion solvent extraction/evaporation method, Biomaterials 22(3) (2001) 231-241. ## [134] R. Zhang, L. Gao, Preparation of nanosized titania by hydrolysis of alkoxide titanium in micelles, Materials research bulletin 37(9) (2002) 1659-1666. ## [135] A.S. Narang, D. Delmarre, D. Gao, Stable drug encapsulation in micelles and microemulsions, International journal of pharmaceutics 345(1-2) (2007) 9-25. ## [136] M.A. Malik, M.Y. Wani, M.A. Hashim, Microemulsion method: A novel route to synthesize organic and inorganic nanomaterials: 1st Nano Update, Arabian Journal of Chemistry 5(4) (2012) 397-417. ## [137] S.F. Chin, A. Azman, S.C. Pang, Size Controlled Synthesis of Starch Nanoparticles by a Microemulsion Method, Journal of Nanomaterials 2014 (2014) 763736. ## [138] H. Liu, J. Mei, Y. Xu, L. Tang, D. Chen, Y. Zhu, S. Huang, T.J. Webster, H. Ding, Improving The Oral Absorption Of Nintedanib By A Self-Microemulsion Drug Delivery System: Preparation And In Vitro/In Vivo Evaluation, International Journal of Nanomedicine 14 (2019) 8739. ## [139] M.B. de Jesus, A. Radaic, I.S. Zuhorn, E. de Paula, Microemulsion extrusion technique: a new method to produce lipid nanoparticles, Journal of nanoparticle research 15(10) (2013) 1960. ## [140] S.P. Callender, J.A. Mathews, K. Kobernyk, S.D. Wettig, Microemulsion utility in pharmaceuticals: Implications for multi-drug delivery, International journal of pharmaceutics 526(1-2) (2017) 425-442. ## [141] B. Yan, Y. Gu, J. Zhao, Y. Liu, L. Wang, Y. Wang, Self-microemulsion Technology for Water-insoluble Drug Delivery, Current Nanoscience 15(6) (2019) 576- 588. ## [142] S.M. Dizaj, F. Lotfpour, M. Barzegar-Jalali, M.-H. Zarrintan, K. Adibkia, Physicochemical characterization and antimicrobial evaluation of gentamicin-loaded CaCO 3 nanoparticles prepared via microemulsion method, Journal of Drug Delivery Science and Technology 35 (2016) 16-23.F. Niazvanda et al. / Journal of Composites and Compounds 2 (2020) 193-204 203 ## [143] M.N. Kelchen, N.K. Brogden, In vitro skin retention and drug permeation through intact and microneedle pretreated skin after application of propranolol loaded microemulsions, Pharmaceutical research 35(12) (2018) 228. ## [144] L. Huang, J. Wu, M. Liu, L. Mao, H. Huang, Q. Wan, Y. Dai, Y. Wen, X. Zhang, Y. Wei, Direct surface grafting of mesoporous silica nanoparticles with phospholipid choline-containing copolymers through chain transfer free radical polymerization and their controlled drug delivery, Journal of colloid and interface science 508 (2017) 396-404. ## [145] L.J. Min, T.Y.S. Edgar, Z. Zicheng, Y.W. Yee, Chapter 6 - Biomaterials for Bioprinting, in: L.G. Zhang, J.P. Fisher, K.W. Leong (Eds.), 3D Bioprinting and Nanotechnology in Tissue Engineering and Regenerative Medicine, Academic Press2015, pp. 129-148. ## [146] Z. Shi, C. Yang, R. Li, L. Ruan, Microwave thermal-triggered drug delivery using thermosensitive peptide-coated core–shell mesoporous silica nanoparticles, Journal of Materials Science 55(14) (2020) 6118-6129. ## [147] R.E. Mardziah, T.W. Wong, Eﬀects of microwave on drug-release responses of spray-dried alginate microspheres, Drug development and industrial pharmacy 36(10) (2010) 1149-1167. ## [148] T. Wong, Use of microwave in processing of drug delivery systems, Current Drug Delivery 5(2) (2008) 77-84. ## [149] H. Qiu, B. Cui, W. Zhao, P. Chen, H. Peng, Y. Wang, A novel microwave stimulus remote controlled anticancer drug release system based on Fe3O4@ZnO@ mGd 2O3: Eu@P(NIPAm-co-MAA) multifunctional nanocarriers, Journal of Materials Chemistry B 3(34) (2015) 6919-6927. ## [150] J. Xu, X. Cheng, L. Tan, C. Fu, M. Ahmed, J. Tian, J. Dou, Q. Zhou, X. Ren, Q. Wu, Microwave responsive nanoplatform via P-selectin mediated drug delivery for treatment of hepatocellular carcinoma with distant metastasis, Nano letters 19(5) (2019) 2914-2927. ## [151] S. Miyazaki, H. Aoyama, N. Kawasaki, W. Kubo, D. Attwood, In situ-gelling gellan formulations as vehicles for oral drug delivery, Journal of Controlled release 60(2-3) (1999) 287-295. ## [152] Y. Wu, Y. Liu, X. Li, D. Kebebe, B. Zhang, J. Ren, J. Lu, J. Li, S. Du, Z. Liu, Research progress of in-situ gelling ophthalmic drug delivery system, Asian Journal of Pharmaceutical Sciences 14(1) (2019) 1-15. ## [153] M. Agrawal, S. Saraf, S. Saraf, S.K. Dubey, A. Puri, U. Gupta, P. Kesharwani, V. Ravichandiran, P. Kumar, V. Naidu, Stimuli-responsive In situ gelling system for nose-to-brain drug delivery, Journal of Controlled Release (2020). ## [154] K. Itoh, T. Hirayama, A. Takahashi, W. Kubo, S. Miyazaki, M. Dairaku, M. Togashi, R. Mikami, D. Attwood, In situ gelling pectin formulations for oral drug delivery at high gastric pH, International journal of pharmaceutics 335(1-2) (2007) 90-96. ## [155] T.N. Nimi, D.R. Manohar, An Overview on In-Situ Nasal Gel for Drug Delivery, Journal of Pharmaceutical Sciences and Research 11(7) (2019) 2585-2589. ## [156] S. Desai, S. Bolton, A ﬂoating controlled-release drug delivery system: in vitro-in vivo evaluation, Pharmaceutical research 10(9) (1993) 1321-1325. ## [157] Z. Shi, X. Chen, L. Zhang, S. Ding, X. Wang, Q. Lei, W. Fang, FA-PEG decorated MOF nanoparticles as a targeted drug delivery system for controlled release of an autophagy inhibitor, Biomaterials science 6(10) (2018) 2582-2590. ## [158] K. Neha, H.S. Nirmala, Insitu gelling system: A Review, J Drug Del and Therapeutics 4(4) (2014) 93-103. ## [159] P. Suradkar, R. Mishra, T. Nandgude, Overview on Trends in Development of Gastroretentive Drug Delivery System, Research Journal of Pharmacy and Technology 12(11) (2019) 5633-5640. ## [160] D. Bhowmik, R. Bhanot, D. Gautam, P. Rai, K. Kumar, Gastro Retentive Drug Delivery Systems-a Novel Approaches of Controlled Drug Delivery Systems, Research Journal of Science and Technology 10(2) (2018) 145-156. ## [161] S. Fredenberg, M. Wahlgren, M. Reslow, A. Axelsson, The mechanisms of drug release in poly (lactic-co-glycolic acid)-based drug delivery systems—a review, International journal of pharmaceutics 415(1-2) (2011) 34-52. ## [162] J. Panyam, V. Labhasetwar, Biodegradable nanoparticles for drug and gene delivery to cells and tissue, Advanced drug delivery reviews 55(3) (2003) 329-347. ## [163] Y. Ma, J.C. Pacan, Q. Wang, Y. Xu, X. Huang, A. Korenevsky, P.M. Sabour, Microencapsulation of bacteriophage Felix O1 into chitosan-alginate microspheres for oral delivery, Applied and environmental microbiology 74(15) (2008) 4799- 4805. ## [164] J. Trygg, E. Yildir, R. Kolakovic, N. Sandler, P. Fardim, Anionic cellulose beads for drug encapsulation and release, Cellulose 21(3) (2014) 1945-1955. ## [165] H. Bao, Y. Pan, Y. Ping, N.G. Sahoo, T. Wu, L. Li, J. Li, L.H. Gan, Chitosan‐ functionalized graphene oxide as a nanocarrier for drug and gene delivery, Small 7(11) (2011) 1569-1578. ## [166] S. Javanbakht, M. Pooresmaeil, H. Namazi, Green one-pot synthesis of carboxymethylcellulose/Zn-based metal-organic framework/graphene oxide bio-nanocomposite as a nanocarrier for drug delivery system, Carbohydrate Polymers 208 (2019) 294-301. ## [167] H.H.P. Duong, L.-Y.L. Yung, Synergistic co-delivery of doxorubicin and paclitaxel using multi-functional micelles for cancer treatment, International journal of pharmaceutics 454(1) (2013) 486-495. ## [168] F. Foroughi, S.A. Hassanzadeh-Tabrizi, A. Bigham, In situ microemulsion synthesis of hydroxyapatite-MgFe2O4 nanocomposite as a magnetic drug delivery system, Materials Science and Engineering: C 68 (2016) 774-779. ## [169] K. Drlica, Biology of bacterial deoxyribonucleic acid topoisomerases, Microbiological reviews 48(4) (1984) 273. ## [170] D. Pathania, D. Gupta, N. Kothiyal, G. Eldesoky, M. Naushad, Preparation of a novel chitosan-g-poly (acrylamide)/Zn nanocomposite hydrogel and its applications for controlled drug delivery of oﬂoxacin, International journal of biological macromolecules 84 (2016) 340-348. ## [171] S. Das, A. Chaudhury, K.Y. Ng, Preparation and evaluation of zinc-pectin-chitosan composite particles for drug delivery to the colon: role of chitosan in modifying in vitro and in vivo drug release, Int J Pharm 406(1-2) (2011) 11-20. ## [172] K. Kompany, E.H. Mirza, S. Hosseini, B. Pingguan-Murphy, I. Djordjevic, Polyoctanediol citrate–ZnO composite flms: Preparation, characterization and release kinetics of nanoparticles from polymer matrix, Materials Letters 126 (2014) 165-168. ## [173] A. Dodero, M. Alloisio, S. Vicini, M. Castellano, Preparation of composite alginate-based electrospun membranes loaded with ZnO nanoparticles, Carbohydrate polymers 227 (2020) 115371. ## [174] W. Artifon, S.M. Pasini, A. Valério, S.Y.G. González, S.M.d.A.G. Ulson, A.A.U. de Souza, Harsh environment resistant-antibacterial zinc oxide/Polyetherimide electrospun composite scaﬀolds, Materials Science and Engineering: C 103 (2019) 109859. ## [175] A. Bhattacharjee, M.K. Purkait, S. Gumma, Loading and release of doxorubicin hydrochloride from Iron (III) trimesate MOF and zinc oxide nanoparticle composites, Dalton Transactions (2020). ## [176] A.U. Kura, S.H.H. Al Ali, M.Z. Hussein, S. Fakurazi, P. Arulselvan, Development of a controlled-release anti-parkinsonian nanodelivery system using levodopa as the active agent, International Journal of Nanomedicine 8 (2013) 1103. ## [177] A. Seyfoori, S.A.S. Ebrahimi, S. Omidian, S.M. Naghib, Multifunctional magnetic ZnFe2O4-hydroxyapatite nanocomposite particles for local anti-cancer drug delivery and bacterial infection inhibition: An in vitro study, Journal of the Taiwan Institute of Chemical Engineers 96 (2019) 503-508. ## [178] A. Nigam, S.J. Pawar, Structural, magnetic, and antimicrobial properties of zinc doped magnesium ferrite for drug delivery applications, Ceramics International 46(4) (2020) 4058-4064. ## [179] Z. Neščáková, K. Zheng, L. Liverani, Q. Nawaz, D. Galusková, H. Kaňková, M. Michálek, D. Galusek, A.R. Boccaccini, Multifunctional zinc ion doped sol – gel derived mesoporous bioactive glass nanoparticles for biomedical applications, Bioactive Materials 4 (2019) 312-321. ## [180] V. Thangaraj, M. Yogapriya, K. Thirumalai, M. Swaminathan, A. Sundaramurthy, R. Nandhakumar, S. Suresh, E. Vakees, A. Araichimani, Sol–Gel Synthesis of Ce 4–xSr1+ xFe5–xZnxO14+δ ## [0≤ x≤ 0.45] Superparamagnetic Oxide Systems and Its Magnetic, Dielectric, and Drug Delivery Properties, ACS omega 3(12) (2018) 16509-16518. ## [181] D. Pathania, D. Gupta, N.C. Kothiyal, G. sharma, G.E. Eldesoky, M. Naushad, Preparation of a novel chitosan-g-poly(acrylamide)/Zn nanocomposite hydrogel and its applications for controlled drug delivery of oﬂoxacin, International Journal of Biological Macromolecules 84 (2016) 340-348. ## [182] M. Khatamian, B. Divband, F. Farahmand-Zahed, Synthesis and characterization of Zinc (II)-loaded Zeolite/Graphene oxide nanocomposite as a new drug carrier, Materials Science and Engineering: C 66 (2016) 251-258. ## [183] R. Rakhshaei, H. Namazi, H. Hamishehkar, H.S. Kafl, R. Salehi, In situ synthesized chitosan–gelatin/ZnO nanocomposite scaﬀold with drug delivery properties: Higher antibacterial and lower cytotoxicity eﬀects, Journal of Applied Polymer Science 136(22) (2019) 47590. ## [184] M. Yadollahi, S. Farhoudian, S. Barkhordari, I. Gholamali, H. Farhadnejad, H. Motasadizadeh, Facile synthesis of chitosan/ZnO bio-nanocomposite hydrogel beads as drug delivery systems, International journal of biological macromolecules 82 (2016) 273-278. ## [185] Z. Yang, L. Wang, Y. Liu, S. Liu, D. Tang, L. Meng, B. Cui, ZnO capped ﬂower-like porous carbon-Fe3O4 composite as carrier for bi-triggered drug delivery, Materials Science and Engineering: C 107 (2020) 110256. ## [186] F. Yang, X. Niu, X. Gu, C. Xu, W. Wang, Y. Fan, Biodegradable Magnesium-Incorporated Poly(l-lactic acid) Microspheres for Manipulation of Drug Release and Alleviation of Inﬂammatory Response, ACS Applied Materials and Interfaces 11(26) (2019) 23546-23557.204 F. Niazvand et al. / Journal of Composites and Compounds 2 (2020) 193-204 ## [187] M. Cheddadi, E. López-Cabarcos, K. Slowing, E. Barcia, A. Fernández-Carballido, Cytotoxicity and biocompatibility evaluation of a poly(magnesium acrylate) hydrogel synthesized for drug delivery, International Journal of Pharmaceutics 413(1) (2011) 126-133. ## [188] N.P. Rijal, U. Adhikari, N. Bhattarai, Magnesium Incorporated Polycaprolactone-Based Composite Nanofbers, ASME 2015 International Mechanical Engineering Congress and Exposition, 2015. ## [189] N.P. Rijal, U. Adhikari, S. Khanal, D. Pai, J. Sankar, N. Bhattarai, Magnesium oxide-poly(ε-caprolactone)-chitosan-based composite nanofber for tissue engineering applications, Materials Science and Engineering: B 228 (2018) 18-27. ## [190] F. Mohammad, T. Arfn, H.A. Al-Lohedan, Sustained drug release and electrochemical performance of ethyl cellulose-magnesium hydrogen phosphate composite, Materials Science and Engineering: C 71 (2017) 735-743. ## [191] F. Foroughi, S. Hassanzadeh-Tabrizi, A. Bigham, In situ microemulsion synthesis of hydroxyapatite-MgFe2O4 nanocomposite as a magnetic drug delivery system, Materials Science and Engineering: C 68 (2016) 774-779. ## [192] Z. Tabia, K. El Mabrouk, M. Bricha, K. Nouneh, Mesoporous bioactive glass nanoparticles doped with magnesium: drug delivery and acellular in vitro bioactivity, RSC advances 9(22) (2019) 12232-12246.##

1 - Recent progress in materials used towards corrosion protection of Mg and its alloys https://www.jourcc.com/index.php/jourcc/article/view/jcc245 10.29252/jcc.2.4.5 1 Magnesium has little resistance to corrosion and therefore its production and use are quite limited. The problem of corrosion associated with these alloys has been alleviated to some extent by the advantages obtained from fine coatings. An additional dense barrier against corrosion is created, using coatings obtained from sol-gel. As an alternative for Cr-based conversion coatings, rare-earth elements-based ones are been increasingly investigated for Mg and its alloys due to being eco-friendly. Because of chemical inertness, low friction, and high hardness, diamond-like carbon (DLC) coatings have exhibited the best protection for Mg and its alloys. In this review, we shed light on recent advancements in novel coatings for Mg alloys including hybrid, rare-earth conversion, composite polymeric (polymer composite is a multi-phase material in which reinforcing fillers are integrated with a polymer matrix), and DLC coatings. 0 - 205 214 - - Hadi Ghazanfari Department of Mining, Metallurgical and Materials Engineering, Université Laval Canada hadi.ghazanfari.1@ulaval.ca - - Saber Hasanizadeh Chemical Engineering Department, Kermanshah University of Technology Iran info@jourcc.com - - Sara Eskandarinezhad Department of Mining and Metallurgy, Yazd University Iran info@jourcc.com - - Soheil Hassani Department of Materials Engineering, Science and Research Branch, Islamic Azad University Iran info@jourcc.com - - Mohsen Sheibani Department of Materials Engineering and Metallurgy, Shiraz Branch, Islamic Azad University Iran info@jourcc.com - - Alireza Dordsheikh Torkamani School of Metallurgy and Materials Engineering, Iran University of Science and Technology (IUST) Iran info@jourcc.com - - Belma Fakić Metallographic laboratory, Institute “Kemal Kapetanović” in Zenica, University of Zenica B and H info@jourcc.com Hybrid coatings Rare-earth Polymeric composite DLC coatings [1] J. Gray, B. Luan, Protective coatings on magnesium and its alloys—a critical review, Journal of alloys and compounds 336(1-2) (2002) 88-113. ##[2] A.H. Shahbaz, M. Esmaeilian, R. NasrAzadani, K. Gavanji, The effect of MgF2 addition on the mechanical properties of hydroxyapatite synthesized via powder metallurgy, Journal of Composites and Compounds 1(1) (2019) 18-24. ##[3] A. Moghanian, A. Ghorbanoghli, M. Kazem‐Rostami, A. Pazhouheshgar, E. Salari, M. Saghafi Yazdi, T. Alimardani, H. Jahani, F. Sharifian Jazi, M. Tahriri, Novel antibacterial Cu/Mg‐substituted 58S‐bioglass: Synthesis, characterization and investigation of in vitro bioactivity, International Journal of Applied Glass Science 11(4) (2020) 685-698. ##[4] H. Liu, F. Cao, G.-L. Song, D. Zheng, Z. Shi, M.S. Dargusch, A. Atrens, Review of the atmospheric corrosion of magnesium alloys, Journal of Materials Science and Technology 35(9) (2019) 2003-2016. ##[5] D. Tawil, Corrosion and surface protection developments, magnesium technology, Proceedings of the Conference, 1986. ##[6] M. Shahin, K. Munir, C. Wen, Y. Li, Magnesium matrix nanocomposites for orthopedic applications: a review from mechanical, corrosion, and biological perspectives, Acta biomaterialia 96 (2019) 1-19. ##[7] M.F. Heragh, S. Eskandarinezhad, A. Dehghan, Ni-Cu matrix composite reinforced with CNTs: preparation, characterization, wear and corrosion behavior, inhibitory effects, Journal of Composites and Compounds 2(4) (2020) 123-128. ##[8] M. Amiri, V.T. Targhi, S. Padervand, S.M.M. Khoei, Corrosion behavior of aluminum oxide coatings created by electrolytic plasma method under different potential regimes, Journal of Composites and Compounds 2(4) (2020) 129-137. ##[9] M. Amiri, S. Padervand, V.T. Targhi, S.M.M. Khoei, Investigation of aluminum oxide coatings created by electrolytic plasma method in different potential regimes, Journal of Composites and Compounds 2(4) (2020) 115-122. ##[10] A. Abuchenari, H. Ghazanfari, M. Siavashi, M. Sabetzadeh, S. Talebi, Z.K. Chemeh, A. Jamavari, A review on development and application of self-healing thermal barrier composite coatings, Journal of Composites and Compounds 2(4) (2020) 147-154. ##[11] S. Lamaka, M. Montemor, A. Galio, M. Zheludkevich, C. Trindade, L. Dick, M. Ferreira, Novel hybrid sol–gel coatings for corrosion protection of AZ31B magnesium alloy, Electrochimica Acta 53(14) (2008) 4773-4783. ##[12] F.S. Jazi, N. Parvin, M. Rabiei, M. Tahriri, Z.M. Shabestari, A.R. Azadmehr, Effect of the synthesis route on the grain size and morphology of ZnO/Ag nanocomposite, Journal of Ceramic Processing Research 13(5) (2012) 523-526. ##[13] C. Lin, S. Fang, Formation of cerium conversion coatings on AZ31 magnesium alloys, Journal of the Electrochemical Society 152(2) (2004) B54. ##[14] F.S. Jazi, N. Parvin, M. Tahriri, M. Alizadeh, S. Abedini, M. Alizadeh, The relationship between the synthesis and morphology of SnO2-Ag2O nanocomposite, Synthesis and Reactivity in Inorganic, Metal-Organic, and Nano-Metal Chemistry 44(5) (2014) 759-764. ##[15] Q. Cheng, X. Guo, X. Hao, Z. Shi, S. Zhu, Z. Cui, Fabrication of Robust Antibacterial Coatings Based on an Organic–Inorganic Hybrid System, ACS applied materials and interfaces 11(45) (2019) 42607-42615. ##[16] S.V. Gnedenkov, S.L. Sinebryukhov, D.V. Mashtalyar, V.S. Egorkin, M.V. Sidorova, A.S. Gnedenkov, Composite polymer-containing protective coatings on magnesium alloy MA8, Corrosion Science 85 (2014) 52-59. ##[17] J. Daraei, Production and characterization of PCL (Polycaprolactone) coated TCP/nanoBG composite scaffolds by sponge foam method for orthopedic applications, Journal of Composites and Compounds 2(1) (2020) 45-50. ##[18] M. Arefian, M. Hojjati, I. Tajzad, A. Mokhtarzade, M. Mazhar, A. Jamavari, A review of Polyvinyl alcohol/Carboxiy methyl cellulose (PVA/CMC) composites for various applications, Journal of Composites and Compounds 2(3) (2020) 69-76. ##[19] A. Zomorodian, M. Garcia, T.M. e Silva, J. Fernandes, M. Fernandes, M. Montemor, Corrosion resistance of a composite polymeric coating applied on biodegradable AZ31 magnesium alloy, Acta Biomaterialia 9(10) (2013) 8660-8670. ##[20] J. Choi, S. Nakao, J. Kim, M. Ikeyama, T. Kato, Corrosion protection of DLC coatings on magnesium alloy, Diamond and Related Materials 16(4) (2007) 1361-1364. ##[21] X.-J. Cui, C.-M. Ning, L.-L. Shang, G.-A. Zhang, X.-Q. Liu, Structure and anticorrosion, friction, and wear characteristics of Pure Diamond-Like Carbon (DLC), Cr-DLC, and Cr-H-DLC films on AZ91D Mg alloy, Journal of Materials Engineering and Performance 28(2) (2019) 1213-1225. ##[22] T. Nakatani, H. Takeuchi, A. Wada, S. Yamashita, Investigation of Anti-Corrosive Performance of a Si-Doped DLC-Coated Magnesium Alloy Stent Deposited by RF-Plasma CVD, Journal of Photopolymer Science and Technology 32(3) (2019) 511-517. ##[23] K. Zhanga, Q. Van Leb, Journal of Composites and Compounds, (2019). ##[24] C. Niranjan, S. Srinivas, M. Ramachandra, An experimental study on depth of cut of AZ91 Magnesium Alloy in abrasive water jet cutting, Materials Today: Proceedings 5(1) (2018) 2884-2890. ##[25] N. Studio, Magnesium and exercise-Blog, (2020). ##[26] L.S. Fard, N.S. Peighambardoust, H.W. Jang, A. Dehghan, N.N.K. Saligheh, M. Iranpour, M.I. Rajabi, The rechargeable aluminum-ion battery with different composite cathodes: A review, Journal of Composites and Compounds 2(4) (2020) 138-146. ##[27] S. Nasibi, K. Alimohammadi, L. Bazli, S. Eskandarinezhad, A. Mohammadi, N. Sheysi, TZNT alloy for surgical implant applications: A systematic review, Journal of Composites and Compounds 2(3) (2020) 62-68. ##[28] K. Zhang, H.W. Jang, Q. Van Le, Production methods of ceramic-reinforced Al-Li matrix composites: A review, Journal of Composites and Compounds 2(3) (2020) 77-84. ##[29] J.-L. Kuo, S. Sugiyama, S.-H. Hsiang, J. Yanagimoto, Investigating the characteristics of AZ61 magnesium alloy on the hot and semi-solid compression test, The International Journal of Advanced Manufacturing Technology 29(7-8) (2006) 670-677. ##[30] X. He, B. Dong, Y. Chen, R. Li, F. Wang, J. Li, Z. Cai, Analysis of magnesium and copper in aluminum alloys with high repetition rate laser-ablation spark-induced breakdown spectroscopy, Spectrochimica Acta Part B: Atomic Spectroscopy 141 (2018) 34-43. ##[31] I. Tajzad, E. Ghasali, Production methods of CNT-reinforced Al matrix composites: a review, Journal of Composites and Compounds 2(1) (2020) 1-9. ##[32] F. Sharifianjazi, M. Moradi, A. Abouchenari, A.H. Pakseresht, A. Esmaeilkhanian, M. Shokouhimehr, M.S. Asl, Effects of Sr and Mg dopants on biological and mechanical properties of SiO2–CaO–P2O5 bioactive glass, Ceramics International (2020). ##[33] A. Bordbar-Khiabani, B. Yarmand, M. Mozafari, Emerging magnesium-based biomaterials for orthopedic implantation, Thomas Telford Ltd, 2019. ##[34] K. Singh, G. Singh, H. Singh, Review on friction stir welding of magnesium alloys, Journal of magnesium and alloys 6(4) (2018) 399-416. ##[35] K. Singh, G. Singh, H. Singh, Investigation of microstructure and mechanical properties of friction stir welded AZ61 magnesium alloy joint, Journal of Magnesium and Alloys 6(3) (2018) 292-298. ##[36] H. Somekawa, A. Kinoshita, A. Kato, Effect of alloying elements on room temperature stretch formability in Mg alloys, Materials Science and Engineering: A 732 (2018) 21-28. ##[37] R. Galun, A. Weisheit, B. Mordike, Laser surface alloying of magnesium base alloys, Journal of Laser Applications 8(6) (1996) 299-305. ##[38] M. Easton, M.A. Gibson, S. Zhu, T. Abbott, J.-F. Nie, C.J. Bettles, G. Savage, Development of magnesium-rare earth die-casting alloys, TMS Annual Meeting and Exhibition, Springer, 2018, pp. 329-336. ##[39] E. Aghion, B. Bronfin, Magnesium alloys development towards the 21st century, Materials Science Forum, Trans Tech Publ, 2000, pp. 19-30. ##[40] A. Abuchenari, M. Moradi, The Effect of Cu-substitution on the microstructure and magnetic properties of Fe-15% Ni alloy prepared by mechanical alloying, Journal of Composites and Compounds 1(1) (2019) 11-17. ##[41] R. Pandey, S. Tekumalla, M. Gupta, Effect of defects on electromagnetic interference shielding effectiveness of magnesium, Journal of Materials Science: Materials in Electronics 29(11) (2018) 9728-9739. ##[42] S. Ben Zaken, O. Simantov, A. Abenstein, Z. Radomysky, G. Koren, Water desalination, serum magnesium and dementia: a population-based study, Journal of Water and Health 18(5) (2020) 722-727. ##[43] A.A. Luo, Magnesium casting technology for structural applications, journal of Magnesium and Alloys 1(1) (2013) 2-22. ##[44] H. Hu, Squeeze casting of magnesium alloys and their composites, Journal of materials science 33(6) (1998) 1579-1589. ##[45] H. Dieringa, K.U. Kainer, Magnesium and Magnesium Alloys, Springer Handbook of Materials Data, Springer2018, pp. 151-159. ##[46] R.H. Buzolin, P. Volovitch, A. Maltseva, S. Lamaka, C. Blawert, C.L. Mendis, A. Lohmüller, K.U. Kainer, N. Hort, Thixomolded AZ91D and MRI153M magnesium alloys and their enhanced corrosion resistance, Materials and corrosion 71(3) (2020) 339-351. ##[47] B. Viswanadhapalli, V.B. Raja, Application of Magnesium Alloys in Automotive Industry-A Review, International Conference on Emerging Current Trends in Computing and Expert Technology, Springer, 2019, pp. 519-531. ##[48] R. Viswanathan, N. Sivashankar, S. Chandrakumar, R. Karthik, Improving Corrosion Resistance of Magnesium Alloy for Aerospace Applications, International Journal of Mechanical and Production Engineering Research and Development 9(3) (2019) 769-774. ##[49] O.I. Velikokhatnyi, P.N. Kumta, First-principles studies on alloying and simplified thermodynamic aqueous chemical stability of calcium-, zinc-, aluminum-, yttrium-and iron-doped magnesium alloys, Acta Biomaterialia 6(5) (2010) 1698-1704. ##[50] M. Bian, X. Huang, Y. Chino, Improving flame resistance and mechanical properties of magnesium–silver–calcium sheet alloy by optimization of calcium content, Journal of Alloys and Compounds (2020) 155551. ##[51] M. Esmaily, J. Svensson, S. Fajardo, N. Birbilis, G. Frankel, S. Virtanen, R. Arrabal, S. Thomas, L. Johansson, Fundamentals and advances in magnesium alloy corrosion, Progress in Materials Science 89 (2017) 92-193. ##[52] A. Toulabifard, M. Rahmati, K. Raeissi, A. Hakimizad, M. Santamaria, The Effect of Electrolytic Solution Composition on the Structure, Corrosion, and Wear Resistance of PEO Coatings on AZ31 Magnesium Alloy, Coatings 10(10) (2020) 937. ##[53] R. Ambat, N.N. Aung, W. Zhou, Evaluation of microstructural effects on corrosion behaviour of AZ91D magnesium alloy, Corrosion science 42(8) (2000) 1433-1455. ##[54] C.H. Chang, K.-T. Wu, C.-T. Lin, Magnesium Alloy Substrate, Google Patents, 2018. ##[55] C. Li, H. Huang, J. Zhao, S. Ruan, A high strength magnesium alloy-based rotating mirror for an ultra-high speed camera, Optik 157 (2018) 85-92. ##[56] G. Song, A.L. Bowles, D.H. StJohn, Corrosion resistance of aged die cast magnesium alloy AZ91D, Materials Science and Engineering: A 366(1) (2004) 74-86. ##[57] D. Klaumünzer, J.V. Hernandez, S. Yi, D. Letzig, S.-h. Kim, J.J. Kim, M.H. Seo, K. Ahn, Magnesium process and alloy development for applications in the automotive industry, Magnesium Technology 2019, Springer2019, pp. 15-20. ##[58] G. Demir, A.U. Malcıoğlu, S. Sağdiç, A. Ulus, S. Aslanlar, E. İlhan, Optimization of Thermo-Mechanical Processes of Continuous Casting Products Using High Magnesium Aluminum Alloys in Automotive Industry Applications, Light Metals 2020, Springer2020, pp. 386-399. ##[59] H. Friedrich, S. Schumann, Research for a “new age of magnesium” in the automotive industry, Journal of Materials Processing Technology 117(3) (2001) 276-281. ##[60] S. Schumann, The paths and strategies for increased magnesium applications in vehicles, Materials Science Forum, Trans Tech Publ, 2005, pp. 1-8. ##[61] M.K. Kulekci, Magnesium and its alloys applications in automotive industry, The International Journal of Advanced Manufacturing Technology 39(9-10) (2008) 851-865. ##[62] F. Czerwinski, Controlling the ignition and flammability of magnesium for aerospace applications, Corrosion Science 86 (2014) 1-16. ##[63] T. Kaneko, M. Suzuki, Automotive applications of magnesium alloys, Materials science forum, Trans Tech Publications Ltd., Zurich-Uetikon, Switzerland, 2003, pp. 67-72. ##[64] P.R. Matli, A.V. Krishnan, V. Manakari, G. Parande, B. Chua, S. Wong, C. Lim, M. Gupta, A new method to lightweight and improve strength to weight ratio of magnesium by creating a controlled defect, Journal of Materials Research and Technology (2020). ##[65] M.P. Staiger, A.M. Pietak, J. Huadmai, G. Dias, Magnesium and its alloys as orthopedic biomaterials: a review, Biomaterials 27(9) (2006) 1728-1734. ##[66] N.-E.L. Saris, E. Mervaala, H. Karppanen, J.A. Khawaja, A. Lewenstam, Magnesium: an update on physiological, clinical and analytical aspects, Clinica chimica acta 294(1-2) (2000) 1-26. ##[67] J.M. Seitz, R. Eifler, F.W. Bach, H. Maier, Magnesium degradation products: effects on tissue and human metabolism, Journal of biomedical materials research Part A 102(10) (2014) 3744-3753. ##[68] T.C. Wallace, Combating COVID-19 and building immune resilience: a potential role for magnesium nutrition?, Journal of the American College of Nutrition (2020) 1-9. ##[69] F. Ahmed, A. Mohammed, Magnesium: the forgotten electrolyte—a review on hypomagnesemia, Medical Sciences 7(4) (2019) 56. ##[70] D. Song, C. Li, N. Liang, F. Yang, J. Jiang, J. Sun, G. Wu, A. Ma, X. Ma, Simultaneously improving corrosion resistance and mechanical properties of a magnesium alloy via equal-channel angular pressing and post water annealing, Materials and Design 166 (2019) 107621. ##[71] D. Seifzadeh, A. Haghighat, Formation of rare earth-permanganate conversion coating on AZ61 magnesium alloy and its properties, (2013). ##[72] S. Kamrani, C. Fleck, Biodegradable magnesium alloys as temporary orthopaedic implants: a review, BioMetals 32(2) (2019) 185-193. ##[73] K. Jafarzadeh, T. Shahrabi, S. Hadavi, M. Hosseini, EIS study on corrosion behavior of AA5083-H321 aluminum-magnesium alloys in stagnant NaCl solution, (2008). ##[74] L. Liu, M. Schlesinger, Corrosion of magnesium and its alloys, Corrosion Science 51(8) (2009) 1733-1737. ##[75] F. Gao, Y. Hu, Z. Gong, T. Liu, T. Gong, S. Liu, C. Zhang, L. Quan, B. Kaveendran, C. Pan, Fabrication of chitosan/heparinized graphene oxide multilayer coating to improve corrosion resistance and biocompatibility of magnesium alloys, Materials Science and Engineering: C 104 (2019) 109947. ##[76] I. Apachitei, L. Fratila-Apachitei, J. Duszczyk, Microgalvanic activity of an Mg–Al–Ca-based alloy studied by scanning Kelvin probe force microscopy, Scripta Materialia 57(11) (2007) 1012-1015. ##[77] G. Song, B. Johannesson, S. Hapugoda, D. StJohn, Galvanic corrosion of magnesium alloy AZ91D in contact with an aluminium alloy, steel and zinc, Corrosion Science 46(4) (2004) 955-977. ##[78] R. Ambat, N.N. Aung, W. Zhou, Effect of pH and chloride ion concentration on the corrosion and electrochemical behaviour of AZ91D magnesium alloy, Journal of Applied Electrochemistry 30 (2000) 865-874. ##[79] S. Mathieu, C. Rapin, J. Steinmetz, P. Steinmetz, A corrosion study of the main constituent phases of AZ91 magnesium alloys, Corrosion Science 45(12) (2003) 2741-2755. ##[80] M. Jönsson, D. Persson, D. Thierry, Corrosion product formation during NaCl induced atmospheric corrosion of magnesium alloy AZ91D, Corrosion Science 49(3) (2007) 1540-1558. ##[81] X. Gu, Y. Zheng, Y. Cheng, S. Zhong, T. Xi, In vitro corrosion and biocompatibility of binary magnesium alloys, Biomaterials 30(4) (2009) 484-498. ##[82] S. Abbasi, M. Aliofkhazraei, H. Mojiri, M. Amini, M. Ahmadzadeh, M. Shourgeshty, Corrosion behavior of pure Mg and AZ31 magnesium alloy, Protection of Metals and Physical Chemistry of Surfaces 53(3) (2017) 573-578. ##[83] N. Liu, W. Huang, DSC study on temperature memory effect of NiTi shape memory alloy, Transactions of Nonferrous Metals Society of China 16 (2006) s37-s41. ##[84] A. Coy, F. Viejo, P. Skeldon, G. Thompson, Susceptibility of rare-earth-magnesium alloys to micro-galvanic corrosion, Corrosion Science 52(12) (2010) 3896-3906. ##[85] M. Toorani, M. Aliofkhazraei, Review of electrochemical properties of hybrid coating systems on Mg with plasma electrolytic oxidation process as pretreatment, Surfaces and Interfaces 14 (2019) 262-295. ##[86] T. Cain, L. Bland, N. Birbilis, J. Scully, A compilation of corrosion potentials for magnesium alloys, Corrosion 70(10) (2014) 1043-1051. ##[87] P. Huang, J.-A. Latham, D.R. MacFarlane, P.C. Howlett, M. Forsyth, A review of ionic liquid surface film formation on Mg and its alloys for improved corrosion performance, Electrochimica Acta 110 (2013) 501-510. ##[88] L. Yan, M. Zhou, X. Pang, K. Gao, One-step in situ synthesis of reduced graphene oxide/Zn–Al layered double hydroxide film for enhanced corrosion protection of magnesium alloys, Langmuir 35(19) (2019) 6312-6320. ##[89] R. Arrabal, A. Pardo, M. Merino, S. Merino, P. Casajús, M. Mohedano, P. Rodrigo, Corrosion behavior of mg-al alloys with aluminum thermal spray coatings in humid and saline environments, Corrosion 65(12) (2009) 817-830. ##[90] M.M. Avedesian, H. Baker, ASM specialty handbook: magnesium and magnesium alloys, ASM international1999. ##[91] J. Li, Y. He, Y. Sun, X. Zhang, W. Shi, D. Ge, Synthesis of Polypyrrole/V2O5 Composite Film on the Surface of Magnesium Using a Mild Vapor Phase Polymerization (VPP) Method for Corrosion Resistance, Coatings 10(4) (2020) 402. ##[92] R. Molak, K. Topolski, M. Spychalski, I. Dulińska-Molak, B. Morończyk, Z. Pakieła, L. Nieużyła, M. Mazurkiewicz, M. Wojucki, A. Gebeshuber, Functional properties of the novel hybrid coatings combined of the oxide and DLC layer as a protective coating for AZ91E magnesium alloy, Surface and Coatings Technology 380 (2019) 125040. ##[93] V.Z. Asl, J. Zhao, M.J. Anjum, S. Wei, W. Wang, Z. Zhao, The effect of cerium cation on the microstructure and anti-corrosion performance of LDH conversion coatings on AZ31 magnesium alloy, Journal of Alloys and Compounds 821 (2020) 153248. ##[94] R.-G. Hu, S. Zhang, J.-F. Bu, C.-J. Lin, G.-L. Song, Recent progress in corrosion protection of magnesium alloys by organic coatings, Progress in Organic Coatings 73(2-3) (2012) 129-141. ##[95] J. Scully, S. Hensley, Lifetime prediction for organic coatings on steel and a magnesium alloy using electrochemical impedance methods, Corrosion 50(9) (1994) 705-716. ##[96] S. Pandey, S.B. Mishra, Sol–gel derived organic–inorganic hybrid materials: synthesis, characterizations and applications, Journal of sol-gel science and technology 59(1) (2011) 73-94. ##[97] M. Faustini, L. Nicole, E. Ruiz‐Hitzky, C. Sanchez, History of organic–inorganic hybrid materials: prehistory, art, science, and advanced applications, Advanced Functional Materials 28(27) (2018) 1704158. ##[98] R. Zandi-Zand, A. Ershad-Langroudi, A. Rahimi, Organic–inorganic hybrid coatings for corrosion protection of 1050 aluminum alloy, Journal of Non-Crystalline Solids 351(14-15) (2005) 1307-1311. ##[99] F. García-Galván, M. Mezour, G. Hickman, I. Soliman, A. Jiménez-Morales, V. Barranco, J. Galván, C. Perry, Organic-inorganic hybrid coatings containing phosphorus precursors prepared by sol–gel on Ti6Al4V alloy: Electrochemical and in-vitro biocompatibility evaluation, Progress in Organic Coatings 148 (2020) 105834. ##[100] N. Farhadyar, A. Rahimi, A. Ershad Langroudi, Synthesis and chracterization of inorganic-organic hybrid produced from tetraethoxysilane and epoxy-aromatic amine, IUPAC World Polymer Congress Macro, 2004, p. 2. ##[101] Z.R. ZANDI, L.A. ERSHAD, A. RAHIMI, Improvement of corrosion resistance of organic-inorganic hybrid coatings based on epoxy-silica via aromatic diol curing agent, (2005). ##[102] C. Sanchez, B. Julián, P. Belleville, M. Popall, Applications of hybrid organic–inorganic nanocomposites, Journal of Materials Chemistry 15(35-36) (2005) 3559-3592. ##[103] J.C.B. Alcázar, R.M.J. Lemos, M.C.M. Conde, L.A. Chisini, M.M.S. Salas, B.S. Noremberg, F.V. da Motta, F.F. Demarco, S.B.C. Tarquinio, N.L.V. Carreño, Preparation, characterization, and biocompatibility of different metal oxide/PEG-based hybrid coating synthesized by sol–gel dip coating method for surface modification of titanium, Progress in Organic Coatings 130 (2019) 206-213. ##[104] M. Masudi, A. Rahimi, R.P. Astaneh, Synthesis, Characterization, and Investigation of Inhibitor Release of the Anticorrosion Sol–Gel Hybrid Nanocomposite Coatings, Protection of Metals and Physical Chemistry of Surfaces 55(2) (2019) 363-370. ##[105] Z.R. Zandi, L.A. ERSHAD, A. Rahimi, Synthesis and characterization of nano-composite hybrid coatings based on 3-glycidoxypropyl-trimethoxysilane and bisphenol A, (2005). ##[106] M. Ochi, R. Takahashi, Phase structure and thermomechanical properties of primary and tertiary amine‐cured epoxy/silica hybrids, Journal of Polymer Science Part B: Polymer Physics 39(11) (2001) 1071-1084. ##[107] Y. Ma, L. Chen, Y. Ye, H. Wan, H. Zhou, J. Chen, Preparation and tribological behaviors of a novel organic-inorganic hybrid resin bonded solid lubricating coating cured by ultraviolet radiation, Progress in Organic Coatings 127 (2019) 348-358. ##[108] S. Amiri, A. Rahimi, Hybrid nanocomposite coating by sol–gel method: A review, Iranian Polymer Journal 25(6) (2016) 559-577. ##[109] C.L. Chiang, C.C.M. Ma, D.L. Wu, H.C. Kuan, Preparation, characterization, and properties of novolac‐type phenolic/SiO2 hybrid organic–inorganic nanocomposite materials by sol–gel method, Journal of Polymer Science Part A: Polymer Chemistry 41(7) (2003) 905-913. ##[110] D. Balgude, A. Sabnis, Sol–gel derived hybrid coatings as an environment friendly surface treatment for corrosion protection of metals and their alloys, Journal of sol-gel science and technology 64(1) (2012) 124-134. ##[111] X. Li, Z. Weng, W. Yuan, X. Luo, H.M. Wong, X. Liu, S. Wu, K.W.K. Yeung, Y. Zheng, P.K. Chu, Corrosion resistance of dicalcium phosphate dihydrate/poly(lactic-co-glycolic acid) hybrid coating on AZ31 magnesium alloy, Corrosion Science 102 (2016) 209-221. ##[112] F. Gao, C. Xu, H. Hu, Q. Wang, Y. Gao, H. Chen, Q. Guo, D. Chen, D. Eder, Biomimetic synthesis and characterization of hydroxyapatite/graphene oxide hybrid coating on Mg alloy with enhanced corrosion resistance, Materials Letters 138 (2015) 25-28. ##[113] R.N. Peres, E.S.F. Cardoso, M.F. Montemor, H.G. de Melo, A.V. Benedetti, P.H. Suegama, Influence of the addition of SiO2 nanoparticles to a hybrid coating applied on an AZ31 alloy for early corrosion protection, Surface and Coatings Technology 303 (2016) 372-384. ##[114] S.V. Lamaka, M.F. Montemor, A.F. Galio, M.L. Zheludkevich, C. Trindade, L.F. Dick, M.G.S. Ferreira, Novel hybrid sol–gel coatings for corrosion protection of AZ31B magnesium alloy, Electrochimica Acta 53(14) (2008) 4773-4783. ##[115] M. Zhang, S. Cai, S. Shen, G. Xu, Y. Li, R. Ling, X. Wu, In-situ defect repairing in hydroxyapatite/phytic acid hybrid coatings on AZ31 magnesium alloy by hydrothermal treatment, Journal of Alloys and Compounds 658 (2016) 649-656. ##[116] M.-H. Kang, T.-S. Jang, H.-D. Jung, S.-M. Kim, H.-E. Kim, Y.-H. Koh, J. Song, Poly (ether imide)-silica hybrid coatings for tunable corrosion behavior and improved biocompatibility of magnesium implants, Biomedical Materials 11(3) (2016) 035003. ##[117] F. Pan, X. Yang, D. Zhang, Chemical nature of phytic acid conversion coating on AZ61 magnesium alloy, Applied Surface Science 255(20) (2009) 8363-8371. ##[118] D. Hawake, D. Albright, Metal Finishing, October l995 (1995) 34-38. ##[119] H. Umehara, M. Takaya, Y. Kojima, An investigation of the structure and corrosion resistance of permanganate conversion coatings on AZ91D magnesium alloy, Materials Transactions 42(8) (2001) 1691-1699. ##[120] M. Gonzalez-Nunez, P. Skeldon, G. Thompson, H. Karimzadeh, Kinetics of the development of a nonchromate conversion coating for magnesium alloys and magnesium-based metal matrix composites, Corrosion 55(12) (1999) 1136-1143. ##[121] M. Gonzalez-Nunez, C. Nunez-Lopez, P. Skeldon, G. Thompson, H. Karimzadeh, P. Lyon, T. Wilks, A non-chromate conversion coating for magnesium alloys and magnesium-based metal matrix composites, Corrosion Science 37(11) (1995) 1763-1772. ##[122] A. Simaranov, A. Marshakov, Y. Mikhailovskii, Formation of Conversion Coatings on Magnesium in Moderately Acidic Chromate Solutions, Zashch. Met. 25(5) (1989) 766-774. ##[123] S. Ono, K. Asami, N. Masuko, Mechanism of chemical conversion coating film growth on magnesium and magnesium alloys, Materials transactions 42(7) (2001) 1225-1231. ##[124] C. Lin, C. Lee, W. Li, Y. Chen, G. Fang, Formation of phosphate/permanganate conversion coating on AZ31 magnesium alloy, Journal of The Electrochemical Society 153(3) (2006) B90. ##[125] W. Zhou, D. Shan, E.-H. Han, W. Ke, Structure and formation mechanism of phosphate conversion coating on die-cast AZ91D magnesium alloy, Corrosion Science 50(2) (2008) 329-337. ##[126] Y. Song, D. Shan, R. Chen, F. Zhang, E.-H. Han, Biodegradable behaviors of AZ31 magnesium alloy in simulated body fluid, Materials Science and Engineering: C 29(3) (2009) 1039-1045. ##[127] A.L. Rudd, C.B. Breslin, F. Mansfeld, The corrosion protection afforded by rare earth conversion coatings applied to magnesium, Corrosion Science 42(2) (2000) 275-288. ##[128] M. Dabala, K. Brunelli, E. Napolitani, M. Magrini, Cerium-based chemical conversion coating on AZ63 magnesium alloy, Surface and Coatings Technology 172(2-3) (2003) 227-232. ##[129] B.R. Fazal, S. Moon, Formation of cerium conversion coatings on AZ31 magnesium alloy, 한국표면공학회지 49(1) (2016) 1-13. ##[130] Y. Xiang, W. Hu, X. Liu, C. Zhao, W. Ding, A study on surface state during the pretreatment of electroless nickel plating on magnesium alloys, Transactions of the IMF 79(1) (2001) 27-29. ##[131] K. Brunelli, M. Dabalà, I. Calliari, M. Magrini, Effect of HCl pre-treatment on corrosion resistance of cerium-based conversion coatings on magnesium and magnesium alloys, Corrosion Science 47(4) (2005) 989-1000. ##[132] M.F. Montemor, A.M. Simões, M.J. Carmezim, Characterization of rare-earth conversion films formed on the AZ31 magnesium alloy and its relation with corrosion protection, Applied Surface Science 253(16) (2007) 6922-6931. ##[133] L. Li, J. Lei, S. Yu, Y. Tian, Q. Jiang, F. Pan, Formation and characterization of cerium conversion coatings on magnesium alloy, Journal of Rare Earths 26(3) (2008) 383-387. ##[134] C. Lin, C. Changguo, W. Ningning, W. Jimin, D. Ling, Study of Cerium and Lanthanum Conversion Coatings on AZ63 Magnesium Alloy Surface, Rare Metal Materials and Engineering 44(2) (2015) 333-338. ##[135] M. Laleh, F. Kargar, A.S. Rouhaghdam, Investigation of rare earth sealing of porous micro-arc oxidation coating formed on AZ91D magnesium alloy, Journal of Rare Earths 30(12) (2012) 1293-1297. ##[136] M. Bazli, L. Bazli, R. Rahmani, S. Mansoor, M. Ahmadi, R. Pouriamanesh, Concrete filled FRP–PVC tubular columns used in the construction sector: A review, Journal of Composites and Compounds 2(4) (2020) 155-162. ##[137] L. Bazli, M.H. Bagherian, M. Karrabi, F. Abbassi‐Sourki, H. Azizi, Effect of starch ratio and compatibilization on the viscoelastic behavior of POE/starch blends, Journal of Applied Polymer Science 137(29) (2020) 48877. ##[138] S.O. Omid, Z. Goudarzi, L.M. Kangarshahi, A. Mokhtarzade, F. Bahrami, Self-expanding stents based on shape memory alloys and shape memory polymers, Journal of Composites and Compounds 2(3) (2020) 92-98. ##[139] P. Abasian, M. Radmansouri, M.H. Jouybari, M.V. Ghasemi, A. Mohammadi, M. Irani, F.S. Jazi, Incorporation of magnetic NaX zeolite/DOX into the PLA/chitosan nanofibers for sustained release of doxorubicin against carcinoma cells death in vitro, International journal of biological macromolecules 121 (2019) 398-406. ##[140] L. Bazli, A. Khavandi, M.A. Boutorabi, M. Karrabi, Morphology and viscoelastic behavior of silicone rubber/EPDM/Cloisite 15A nanocomposites based on Maxwell model, Iranian Polymer Journal 25(11) (2016) 907-918. ##[141] L. Bazli, A. Khavandi, M.A. Boutorabi, M. Karrabi, Correlation between viscoelastic behavior and morphology of nanocomposites based on SR/EPDM blends compatibilized by maleic anhydride, Polymer 113 (2017) 156-166. ##[142] S. Pourhashem, F. Saba, J. Duan, A. Rashidi, F. Guan, E.G. Nezhad, B. Hou, Polymer/Inorganic Nanocomposite Coatings with Superior Corrosion Protection Performance: A Review, Journal of Industrial and Engineering Chemistry (2020). ##[143] A. Uriondo, M. Esperon-Miguez, S. Perinpanayagam, The present and future of additive manufacturing in the aerospace sector: A review of important aspects, Proceedings of the Institution of Mechanical Engineers, Part G: Journal of Aerospace Engineering 229(11) (2015) 2132-2147. ##[144] A. Kausar, A review of filled and pristine polycarbonate blends and their applications, Journal of Plastic Film and Sheeting 34(1) (2018) 60-97. ##[145] M. Quaresimin, M. Salviato, M. Zappalorto, Strategies for the assessment of nanocomposite mechanical properties, Composites Part B: Engineering 43(5) (2012) 2290-2297. ##[146] F. Awaja, S. Zhang, M. Tripathi, A. Nikiforov, N. Pugno, Cracks, microcracks and fracture in polymer structures: Formation, detection, autonomic repair, Progress in Materials Science 83 (2016) 536-573. ##[147] A. Kausar, Corrosion prevention prospects of polymeric nanocomposites: A review, Journal of Plastic Film and Sheeting 35(2) (2019) 181-202. ##[148] C. Min, P. Nie, W. Tu, C. Shen, X. Chen, H. Song, Preparation and tribological properties of polyimide/carbon sphere microcomposite films under seawater condition, Tribology International 90 (2015) 175-184. ##[149] A.A. Nazeer, E. Al-Hetlani, M.O. Amin, T. Quiñones-Ruiz, I.K. Lednev, A poly(butyl methacrylate)/graphene oxide/TiO2 nanocomposite coating with superior corrosion protection for AZ31 alloy in chloride solution, Chemical Engineering Journal 361 (2019) 485-498. ##[150] F. Soleymani, R. Emadi, S. Sadeghzade, F. Tavangarian, Applying baghdadite/PCL/chitosan nanocomposite coating on AZ91 magnesium alloy to improve corrosion behavior, bioactivity, and biodegradability, Coatings 9(12) (2019) 789. ##[151] K. Catt, H. Li, X.T. Cui, Poly (3,4-ethylenedioxythiophene) graphene oxide composite coatings for controlling magnesium implant corrosion, Acta Biomaterialia 48 (2017) 530-540. ##[152] N. Rahimi Roshan, H. Hassannejad, A. Nouri, Corrosion and mechanical behaviour of biodegradable PLA-cellulose nanocomposite coating on AZ31 magnesium alloy, Surface Engineering (2020) 1-10. ##[153] Y. Zhang, Y. Shao, T. Zhang, G. Meng, F. Wang, High corrosion protection of a polyaniline/organophilic montmorillonite coating for magnesium alloys, Progress in Organic Coatings 76(5) (2013) 804-811. ##[154] B.-D. Hahn, D.-S. Park, J.-J. Choi, J. Ryu, W.-H. Yoon, J.-H. Choi, H.-E. Kim, S.-G. Kim, Aerosol deposition of hydroxyapatite–chitosan composite coatings on biodegradable magnesium alloy, Surface and Coatings Technology 205(8) (2011) 3112-3118. ##[155] I. Johnson, K. Akari, H. Liu, Nanostructured hydroxyapatite/poly(lactic-co-glycolic acid) composite coating for controlling magnesium degradation in simulated body fluid, Nanotechnology 24(37) (2013) 375103. ##[156] Y. Wang, N. Yamada, J. Xu, J. Zhang, Q. Chen, Y. Ootani, Y. Higuchi, N. Ozawa, M.-I.D.B. Bouchet, J.M. Martin, Triboemission of hydrocarbon molecules from diamond-like carbon friction interface induces atomic-scale wear, Science advances 5(11) (2019) eaax9301. ##[157] H. Yoshinaka, S. Inubushi, T. Wakita, T. Yokoya, Y. Muraoka, Formation of Q-carbon by adjusting sp3 content in diamond-like carbon films and laser energy density of pulsed laser annealing, Carbon 167 (2020) 504-511. ##[158] Z. Ren, H. Qin, Y. Dong, G. Doll, C. Ye, A boron-doped diamond like carbon coating with high hardness and low friction coefficient, Wear 436 (2019) 203031. ##[159] Y. Lei, J. Jiang, Y. Wang, T. Bi, L. Zhang, Structure evolution and stress transition in diamond-like carbon films by glancing angle deposition, Applied Surface Science 479 (2019) 12-19. ##[160] A. Moreno-Bárcenas, J. Alvarado-Orozco, J.G. Carmona, G. Mondragón-Rodríguez, J. González-Hernández, A. García-García, Synergistic effect of plasma nitriding and bias voltage on the adhesion of diamond-like carbon coatings on M2 steel by PECVD, Surface and Coatings Technology 374 (2019) 327-337. ##[161] N. Konkhunthot, P. Photongkam, P. Wongpanya, Improvement of thermal stability, adhesion strength and corrosion performance of diamond-like carbon films with titanium doping, Applied Surface Science 469 (2019) 471-486. ##[162] C.A. Love, R.B. Cook, T.J. Harvey, P.A. Dearnley, R.J.K. Wood, Diamond like carbon coatings for potential application in biological implants—a review, Tribology International 63 (2013) 141-150. ##[163] A. Mazare, A. Anghel, C. Surdu-Bob, G. Totea, I. Demetrescu, D. Ionita, Silver doped diamond-like carbon antibacterial and corrosion resistance coatings on titanium, Thin Solid Films 657 (2018) 16-23. ##[164] G. Wu, W. Dai, H. Zheng, A. Wang, Improving wear resistance and corrosion resistance of AZ31 magnesium alloy by DLC/AlN/Al coating, Surface and Coatings Technology 205(7) (2010) 2067-2073. ##[165] Y.L. Wei, L.L. Huang, L.J. Han, Y.S. Chen, Corrosion resistance and surface biocompatibility of diamond-like carbon coating on AZ31D magnesium alloy, International Journal of Surface Science and Engineering 10(2) (2016) 101-115. ##[166] C.-M. Ning, X.-J. Cui, L.-L. Shang, Y.-J. Zhang, G.-A. Zhang, Structure and properties of different elements doped diamond-like carbon on micro-arc oxidation coated AZ31B Mg alloy, Diamond and Related Materials (2020) 107832. ##[167] G. Wu, L. Sun, W. Dai, L. Song, A. Wang, Influence of interlayers on corrosion resistance of diamond-like carbon coating on magnesium alloy, Surface and Coatings Technology 204(14) (2010) 2193-2196. ##[168] I. Masami, N. Setsuo, S. Tsutomu, C. Junho, Improvement of corrosion protection property of Mg-alloy by DLC and Si–DLC coatings with PBII technique and multi-target DC–RF magnetron sputtering, Nuclear Instruments and Methods in Physics Research Section B: Beam Interactions with Materials and Atoms 267(8) (2009) 1675-1679. ##[169] Y. Uematsu, T. Kakiuchi, T. Teratani, Y. Harada, K. Tokaji, Improvement of corrosion fatigue strength of magnesium alloy by multilayer diamond-like carbon coatings, Surface and Coatings Technology 205(8) (2011) 2778-2784. ##[170] N. Yamauchi, N. Ueda, A. Okamoto, T. Sone, M. Tsujikawa, S. Oki, DLC coating on Mg–Li alloy, Surface and Coatings Technology 201(9) (2007) 4913-4918. ##

1 - Nanodiamond-containing composites for tissue scaﬀolds and surgical implants: A review https://www.jourcc.com/index.php/jourcc/article/view/jcc246 10.29252/jcc.2.4.6 1 Due to promising properties such as low toxicity against diﬀerent cell lines, being highly stable ﬂuorescent without showing photobleaching, and good surface properties, nanodiamonds have gained ever-increasing attention for various biomedical applications including bioimaging and therapeutic applications. Various methods are used for the fabrication of nanostructured diamond, the commonly used of which is the denotation technique. Newer approaches are being practiced for the modifcation and functionalization of their surfaces by diﬀerent biomolecules suitable for interaction with considered targets. In this review, the scope and recent advancement in the feld of nanodiamonds for biomedical applications particularly their application for nanocomposite scaﬀold and implants are discussed. 0 - 215 227 - - Yasamin Zamani Department of Biology, Tehran Medical Sciences Branch, Islamic Azad University Iran info@jourcc.com - - Ali Zareein Department of Biomedical Engineering, Tabriz Branch, Islamic Azad University Iran info@jourcc.com - - Leila Bazli School of Metallurgy and Materials Engineering, Iran University of Science and Technology Iran info@jourcc.com - - Reyhaneh Nasr Azadani Department of Biomaterials Nanotechnology and Tissue engineering, Isfahan University of Medical Sciences Iran info@jourcc.com - - Babar Pasha Mahammod National Institute of Technology Warangal India info@jourcc.com - - Shima Nasibi Department of Materials Science and Engineering, Shiraz University Iran info@jourcc.com - - Amir Modarresi Chahardehi Integrative Medicine Cluster, Advanced Medical and Dental Institute, Universiti Sains Malaysia Malaysia amirmch@gmail.com Nanodiamonds Surface modifcation Biomedical application Nanocomposite scaﬀold Implants [1] O. Shenderova, V. Zhirnov, D. Brenner, Solid State Mater, Sci 27(3/4) (2002) 227. ##[2] J. Sung, Diamond nanotechnology: Synthesis and applications, CRC Press2019. ##[3] Y. Zhang, K.Y. Rhee, D. Hui, S.-J. Park, A critical review of nanodiamond based nanocomposites: Synthesis, properties and applications, Composites Part B: Engineering 143 (2018) 19-27. ##[4] W. Ahmed, S. Gul, M. Awais, Z.U. Hassan, S. Jabeen, M. Farooq, A review: novel nanohybrids of epoxy/polyamide with carbon nanotube/nano-diamond, Polymer-Plastics Technology and Materials (2020) 1-22. ##[5] H. Schwertfeger, A.A. Fokin, P.R. Schreiner, Diamonds are a chemist's best friend: diamondoid chemistry beyond adamantane, Angewandte Chemie International Edition 47(6) (2008) 1022-1036. ##[6] T. Da Ros, M. Prato, Medicinal chemistry with fullerenes and fullerene derivatives, Chemical Communications (8) (1999) 663-669. ##[7] S. Ong, R. Van Harmelen, N. Norouzi, F. Offens, I. Venema, M.H. Najafi, R. Schirhagl, Interaction of nanodiamonds with bacteria, Nanoscale 10(36) (2018) 17117-17124. ##[8] H.-S. Jung, K.-J. Cho, S.-J. Ryu, Y. Takagi, P.A. Roche, K.C. Neuman, Biocompatible Fluorescent Nanodiamonds as Multifunctional Optical Probes for Latent Fingerprint Detection, ACS Applied Materials and Interfaces 12(5) (2020) 6641-6650. ##[9] K. van der Laan, M. Hasani, T. Zheng, R. Schirhagl, Nanodiamonds for in vivo applications, Small 14(19) (2018) 1703838. ##[10] E. Perevedentseva, Y.-C. Lin, C.-L. Cheng, A review of recent advances in nanodiamond-mediated drug delivery in cancer, Expert Opinion on Drug Delivery (2020) 1-14. ##[11] M. Abnikia, Z. Azizi, H. Ahmad-Panahib, A. Pashaeia, Modification of zinc sulfide nanoparticle by allyl glycidyl ether for adsorption of famotidine in biological sample, (2013). ##[12] E. Krok, S. Balakin, J. Jung, F. Gross, J. Opitz, G. Cuniberti, Modification of titanium implants using biofunctional nanodiamonds for enhanced antimicrobial properties, Nanotechnology 31(20) (2020) 205603. ##[13] S. Szunerits, R. Boukherroub, Diamond nanoparticles. A review of selected surface modification. Methods for bioconjugation, biology and medicine, Applied Surface Chemistry of Nanomaterials (2013) 3. ##[14] A.J. Rad, Synthesis of copper oxide nanoparticles on activated carbon for pollutant removal in Tartrazine structure, Journal of Composites and Compounds 2(3) (2020) 99-104. ##[15] L. Bazli, M. Siavashi, A. Shiravi, A review of carbon nanotube/TiO2 composite prepared via sol-gel method, Journal of Composites and Compounds 1(1) (2019) 1-9. ##[16] E. Asadi, A.F. Chimeh, S. Hosseini, S. Rahimi, B. Sarkhosh, L. Bazli, R. Bashiri, A.H.V. Tahmorsati, A review of clinical applications of graphene quantum dot-based composites, Journal of Composites and Compounds 1(1) (2019) 36-47. ##[17] M. Alizadeh, F. Sharifianjazi, E. Haghshenasjazi, M. Aghakhani, L. Rajabi, Production of nanosized boron oxide powder by high-energy ball milling, Synthesis and Reactivity in Inorganic, Metal-Organic, and Nano-Metal Chemistry 45(1) (2015) 11-14. ##[18] K. Zhang, Q. Zhao, S. Qin, Y. Fu, R. Liu, J. Zhi, C. Shan, Nanodiamonds conjugated upconversion nanoparticles for bio-imaging and drug delivery, Journal of colloid and interface science 537 (2019) 316-324. ##[19] H. Tinwala, S. Wairkar, Production, surface modification and biomedical applications of nanodiamonds: A sparkling tool for theranostics, Materials Science and Engineering: C 97 (2019) 913-931. ##[20] J.F.Y. Fong, Y.H. Ng, S. MukNg, Recent Advances in Carbon Dots for Bioanalysis and the Future Perspectives, Carbon Nanomaterials for Bioimaging, Bioanalysis, and Therapy (2019) 203-264. ##[21] M. Fujiwara, S. Sun, A. Dohms, Y. Nishimura, K. Suto, Y. Takezawa, K. Oshimi, L. Zhao, N. Sadzak, Y. Umehara, Real-time nanodiamond thermometry probing\textit {in-vivo} thermogenic responses, arXiv preprint arXiv:2001.02844 (2020). ##[22] K. Gonsalves, C. Halberstadt, C.T. Laurencin, L. Nair, Biomedical nanostructures, John Wiley and Sons2007. ##[23] V. Labhasetwar, D.L. Leslie-Pelecky, Biomedical applications of nanotechnology, John Wiley and Sons2007. ##[24] O.V. Salata, Applications of nanoparticles in biology and medicine, Journal of nanobiotechnology 2(1) (2004) 3. ##[25] E. BioMEMS, By GA Urban, Springer, 2006. ##[26] M.T. Castaneda, A. Merkoçi, M. Pumera, S. Alegret, Electrochemical genosensors for biomedical applications based on gold nanoparticles, Biosensors and Bioelectronics 22(9-10) (2007) 1961-1967. ##[27] A. Merkoçi, Electrochemical biosensing with nanoparticles, The FEBS journal 274(2) (2007) 310-316. ##[28] O. Shoseyov, I. Levy, Nanobiotechnology Overview, NanoBioTechnology, Springer2008, pp. 3-15. ##[29] V. Balouchi, F.S. Jazi, A. Saidi, Developing (W, Ti) C-(Ni, Co) nanocomposite by SHS method, Journal of Ceramic Processing Research 16(5) (2015) 605-608. ##[30] I. Tajzad, E. Ghasali, Production methods of CNT-reinforced Al matrix composites: a review, Journal of Composites and Compounds 2(1) (2020) 1-9. ##[31] M.F. Heragh, S. Eskandarinezhad, A. Dehghan, Ni-Cu matrix composite reinforced with CNTs: preparation, characterization, wear and corrosion behavior, inhibitory effects, Journal of Composites and Compounds 2(4) (2020) 123-128. ##[32] S.J. Cobb, F.H. Laidlaw, G. West, G. Wood, M.E. Newton, R. Beanland, J.V. Macpherson, Assessment of acid and thermal oxidation treatments for removing sp2 bonded carbon from the surface of boron doped diamond, Carbon (2020). ##[33] J. Viecelli, S. Bastea, J. Glosli, F. Ree, Phase transformations of nanometer size carbon particles in shocked hydrocarbons and explosives, The Journal of Chemical Physics 115(6) (2001) 2730-2736. ##[34] V. Danilenko, Synthesis, properties and applications of ultrananocrystalline diamond, Proceedings of the NATO Advanced Research Workshop, 2005, pp. 181-198. ##[35] S.O. Omid, Z. Goudarzi, L.M. Kangarshahi, A. Mokhtarzade, F. Bahrami, Self-expanding stents based on shape memory alloys and shape memory polymers, Journal of Composites and Compounds 2(3) (2020) 92-98. ##[36] F. Sharifianjazi, A.H. Pakseresht, M.S. Asl, A. Esmaeilkhanian, H.W. Jang, M. Shokouhimehr, Hydroxyapatite consolidated by zirconia: applications for dental implant, Journal of Composites and Compounds 2(1) (2020) 26-34. ##[37] E. Perevedentseva, Y.-C. Lin, M. Jani, C.-L. Cheng, Biomedical applications of nanodiamonds in imaging and therapy, Nanomedicine 8(12) (2013) 2041-2060. ##[38] D.-K. Lee, S. Ha, S. Jeon, J. Jeong, D.-J. Kim, S.W. Lee, W.-S. Cho, The sp3/sp2 carbon ratio as a modulator of in vivo and in vitro toxicity of the chemically purified detonation-synthesized nanodiamond via the reactive oxygen species generation, Nanotoxicology (2020) 1-14. ##[39] F.S. Boi, X. Zhang, D. Medranda, Evidence of sp3-rich nano-diamond-like characteristics in amorphous carbon foam continuously filled with α-Fe, Diamond and Related Materials 84 (2018) 190-195. ##[40] O. Shenderova, V. Zhirnov, D. Brenner, Carbon nanostructures, Critical reviews in solid state and material sciences 27(3-4) (2002) 227-356. ##[41] D.M. Gruen, Ultrananocrystalline Diamond, William Andrew2006. ##[42] D.M. Gruen, Nanocrystalline diamond films, Annual Review of Materials Science 29(1) (1999) 211-259. ##[43] V.Y. Dolmatov, The Amount of Impurity Elements in Diamond-Containing Soot and Detonation Nanodiamonds upon Nitric Acid Treatment, Journal of Superhard Materials 40(2) (2018) 143-154. ##[44] A.A. Vozniakovskii, T.S. Kol'tsova, A.P. Voznyakovskii, A.L. Kumskov, S.V. Kidalov, Powder hybrid nanomaterial: Detonation nanodiamonds–Carbon nanotubes and its stable reversible water nanofluids, Journal of Colloid and Interface Science 565 (2020) 305-314. ##[45] J.-P. Boudou, P.A. Curmi, F. Jelezko, J. Wrachtrup, P. Aubert, M. Sennour, G. Balasubramanian, R. Reuter, A. Thorel, E. Gaffet, High yield fabrication of fluorescent nanodiamonds, Nanotechnology 20(23) (2009) 235602. ##[46] I.M. Abdullahi, M. Langenderfer, O. Shenderova, N. Nunn, M.D. Torelli, C. Johnson, V.N. Mochalin, Explosive fragmentation of luminescent diamond particles, Carbon (2020). ##[47] G.-W. Yang, J.-B. Wang, Q.-X. Liu, Preparation of nano-crystalline diamonds using pulsed laser induced reactive quenching, Journal of Physics: Condensed Matter 10(35) (1998) 7923. ##[48] E. Galimov, A. Kudin, V. Skorobogatskii, V. Plotnichenko, O. Bondarev, B. Zarubin, V. Strazdovskii, A. Aronin, A. Fisenko, I. Bykov, Experimental corroboration of the synthesis of diamond in the cavitation process, Doklady Physics, Springer, 2004, pp. 150-153. ##[49] F. Banhart, P.M. Ajayan, Carbon onions as nanoscopic pressure cells for diamond formation, Nature 382(6590) (1996) 433-435. ##[50] T. Daulton, M. Kirk, R. Lewis, L. Rehn, Production of nanodiamonds by high-energy ion irradiation of graphite at room temperature, Nuclear Instruments and Methods in Physics Research Section B: Beam Interactions with Materials and Atoms 175 (2001) 12-20. ##[51] S. Welz, Y. Gogotsi, M.J. McNallan, Nucleation, growth, and graphitization of diamond nanocrystals during chlorination of carbides, Journal of applied physics 93(7) (2003) 4207-4214. ##[52] Y.G. Gogotsi, K.G. Nickel, D. Bahloul-Hourlier, T. Merle-Mejean, G.E. Khomenko, K.P. Skjerlie, Structure of carbon produced by hydrothermal treatment of β-SiC powder, Journal of Materials Chemistry 6(4) (1996) 595-604. ##[53] M. Frenklach, W. Howard, D. Huang, J. Yuan, K. Spear, R. Koba, Induced nucleation of diamond powder, Applied physics letters 59(5) (1991) 546-548. ##[54] O. Guillois, G. Ledoux, C. Reynaud, Diamond infrared emission bands in circumstellar media, The astrophysical journal letters 521(2) (1999) L133. ##[55] M. Goto, T. Henning, A. Kouchi, H. Takami, Y. Hayano, T. Usuda, N. Takato, H. Terada, S. Oya, C. Jäger, Spatially resolved 3 μm spectroscopy of Elias 1: Origin of diamonds in protoplanetary disks, The Astrophysical Journal 693(1) (2009) 610. ##[56] O.A. Shenderova, D.M. Gruen, Ultrananocrystalline diamond: synthesis, properties and applications, William Andrew2012. ##[57] V.Y. Dolmatov, Detonation synthesis ultradispersed diamonds: properties and applications, Russian Chemical Reviews 70(7) (2001) 607-626. ##[58] C. Torres-Sanchez, N. Balodimos, Effective and Eco-friendly Lubrication Protocol Using Nanodiamonds in a Dry Regime for Conveyor Systems in the Beverage Industry, Packaging Technology and Science 30(5) (2017) 209-218. ##[59] I. Senthilnathan, Surface analysis of Detonation Nanodiamond thin films fabricated using automated spray coating technique, (2018). ##[60] S. Osswald, G. Yushin, V. Mochalin, S.O. Kucheyev, Y. Gogotsi, Control of sp2/sp3 carbon ratio and surface chemistry of nanodiamond powders by selective oxidation in air, Journal of the American Chemical Society 128(35) (2006) 11635-11642. ##[61] S. Kumar, M. Nehra, D. Kedia, N. Dilbaghi, K. Tankeshwar, K.-H. Kim, Nanodiamonds: Emerging face of future nanotechnology, Carbon 143 (2019) 678-699. ##[62] F.S. Jazi, N. Parvin, M. Rabiei, M. Tahriri, Z.M. Shabestari, A.R. Azadmehr, Effect of the synthesis route on the grain size and morphology of ZnO/Ag nanocomposite, Journal of Ceramic Processing Research 13(5) (2012) 523-526. ##[63] O. Shenderova, A. Koscheev, N. Zaripov, I. Petrov, Y. Skryabin, P. Detkov, S. Turner, G. Van Tendeloo, Surface chemistry and properties of ozone-purified detonation nanodiamonds, The Journal of Physical Chemistry C 115(20) (2011) 9827-9837. ##[64] M. Sievänen, Agglomeration of nanodiamonds during deposition, (2017). ##[65] O.A. Williams, J. Hees, C. Dieker, W. Jäger, L. Kirste, C.E. Nebel, Size-dependent reactivity of diamond nanoparticles, ACS nano 4(8) (2010) 4824-4830. ##[66] A.M. Schrand, S.A.C. Hens, O.A. Shenderova, Nanodiamond particles: properties and perspectives for bioapplications, Critical reviews in solid state and materials sciences 34(1-2) (2009) 18-74. ##[67] C. Shuai, Y. Li, G. Wang, W. Yang, S. Peng, P. Feng, Surface modification of nanodiamond: Toward the dispersion of reinforced phase in poly-l-lactic acid scaffolds, International Journal of Biological Macromolecules 126 (2019) 1116-1124. ##[68] H. Huang, E. Pierstorff, E. Osawa, D. Ho, Active nanodiamond hydrogels for chemotherapeutic delivery, Nano letters 7(11) (2007) 3305-3314. ##[69] O. Fedyanina, P. Nesterenko, Regularities of chromatographic retention of phenols on microdispersed sintered detonation nanodiamond in aqueous—organic solvents, Russian Journal of Physical Chemistry A 84(3) (2010) 476-480. ##[70] D.H. Jariwala, D. Patel, S. Wairkar, Surface functionalization of nanodiamonds for biomedical applications, Materials Science and Engineering: C (2020) 110996. ##[71] M. Ozawa, M. Inaguma, M. Takahashi, F. Kataoka, A. Krueger, E. Ōsawa, Preparation and behavior of brownish, clear nanodiamond colloids, Advanced Materials 19(9) (2007) 1201-1206. ##[72] E. Ōsawa, Recent progress and perspectives in single-digit nanodiamond, Diamond and Related Materials 16(12) (2007) 2018-2022. ##[73] A. Aleksenskiy, E. Eydelman, A.Y. Vul, Deagglomeration of detonation nanodiamonds, Nanoscience and Nanotechnology Letters 3(1) (2011) 68-74. ##[74] A. Pentecost, S. Gour, V. Mochalin, I. Knoke, Y. Gogotsi, Deaggregation of nanodiamond powders using salt-and sugar-assisted milling, ACS applied materials and interfaces 2(11) (2010) 3289-3294. ##[75] A. Krueger, J. Stegk, Y. Liang, L. Lu, G. Jarre, Biotinylated nanodiamond: simple and efficient functionalization of detonation diamond, Langmuir 24(8) (2008) 4200-4204. ##[76] Y. Liang, T. Meinhardt, G. Jarre, M. Ozawa, P. Vrdoljak, A. Schöll, F. Reinert, A. Krueger, Deagglomeration and surface modification of thermally annealed nanoscale diamond, Journal of Colloid and Interface Science 354(1) (2011) 23-30. ##[77] M. Gu, T.B. Toh, L. Hooi, J.J. Lim, X. Zhang, E.K.-H. Chow, Nanodiamond-mediated delivery of a G9a inhibitor for hepatocellular carcinoma therapy, ACS Applied Materials and Interfaces 11(49) (2019) 45427-45441. ##[78] A. Shvidchenko, E. Eidelman, A.Y. Vul, N. Kuznetsov, D.Y. Stolyarova, S. Belousov, S. Chvalun, Colloids of detonation nanodiamond particles for advanced applications, Advances in Colloid and Interface Science 268 (2019) 64-81. ##[79] V. Bondar’, A. Puzyr’, Nanodiamonds for biological investigations, Physics of the Solid State 46 (2004) 716-719. ##[80] O. Shenderova, I. Petrov, J. Walsh, V. Grichko, V. Grishko, T. Tyler, G. Cunningham, Modification of detonation nanodiamonds by heat treatment in air, Diamond and related materials 15(11-12) (2006) 1799-1803. ##[81] I. Larionova, V. Kuznetsov, A. Frolov, O. Shenderova, S. Moseenkov, I. Mazov, Properties of individual fractions of detonation nanodiamond, Diamond and related materials 15(11-12) (2006) 1804-1808. ##[82] V. Grichko, T. Tyler, V.I. Grishko, O. Shenderova, Nanodiamond particles forming photonic structures, Nanotechnology 19(22) (2008) 225201. ##[83] T. Meinhardt, D. Lang, H. Dill, A. Krueger, Pushing the functionality of diamond nanoparticles to new horizons: orthogonally functionalized nanodiamond using click chemistry, Advanced Functional Materials 21(3) (2011) 494-500. ##[84] A. Krueger, Diamond nanoparticles: jewels for chemistry and physics, Advanced Materials 20(12) (2008) 2445-2449. ##[85] A. Krueger, The structure and reactivity of nanoscale diamond, Journal of Materials Chemistry 18(13) (2008) 1485-1492. ##[86] J.-C. Arnault, T. Petit, H. Girard, A. Chavanne, C. Gesset, M. Sennour, M. Chaigneau, Surface chemical modifications and surface reactivity of nanodiamonds hydrogenated by CVD plasma, Physical Chemistry Chemical Physics 13(24) (2011) 11481-11487. ##[87] Y. Liu, Z. Gu, J.L. Margrave, V.N. Khabashesku, Functionalization of nanoscale diamond powder: fluoro-, alkyl-, amino-, and amino acid-nanodiamond derivatives, Chemistry of materials 16(20) (2004) 3924-3930. ##[88] G. Lisichkin, V. Korol’kov, B. Tarasevich, I. Kulakova, A. Karpukhin, Photochemical chlorination of nanodiamond and interaction of its modified surface with C-nucleophiles, Russian chemical bulletin 55(12) (2006) 2212-2219. ##[89] A. Krueger, T. Boedeker, Deagglomeration and functionalisation of detonation nanodiamond with long alkyl chains, Diamond and related materials 17(7-10) (2008) 1367-1370. ##[90] Y. Liang, M. Ozawa, A. Krueger, A general procedure to functionalize agglomerating nanoparticles demonstrated on nanodiamond, ACS nano 3(8) (2009) 2288-2296. ##[91] P. Gaur, S. Banerjee, C-N cross coupling: Novel approach towards effective aryl secondary amines modification on nanodiamond surface, Diamond and Related Materials 98 (2019) 107468. ##[92] G. Reina, L. Zhao, A. Bianco, N. Komatsu, Chemical functionalization of nanodiamonds: opportunities and challenges ahead, Angewandte Chemie 131(50) (2019) 18084-18095. ##[93] W.S. Yeap, S. Chen, K.P. Loh, Detonation nanodiamond: an organic platform for the suzuki coupling of organic molecules, Langmuir 25(1) (2009) 185-191. ##[94] L. Lai, A.S. Barnard, Modeling the thermostability of surface functionalisation by oxygen, hydroxyl, and water on nanodiamonds, Nanoscale 3(6) (2011) 2566-2575. ##[95] L. Lai, A.S. Barnard, Stability of nanodiamond surfaces exposed to N, NH, and NH2, The Journal of Physical Chemistry C 115(14) (2011) 6218-6228. ##[96] Y.-R. Chang, H.-Y. Lee, K. Chen, C.-C. Chang, D.-S. Tsai, C.-C. Fu, T.-S. Lim, Y.-K. Tzeng, C.-Y. Fang, C.-C. Han, Mass production and dynamic imaging of fluorescent nanodiamonds, Nature nanotechnology 3(5) (2008) 284-288. ##[97] L. Rondin, G. Dantelle, A. Slablab, F. Grosshans, F. Treussart, P. Bergonzo, S. Perruchas, T. Gacoin, M. Chaigneau, H.-C. Chang, Surface-induced charge state conversion of nitrogen-vacancy defects in nanodiamonds, Physical Review B 82(11) (2010) 115449. ##[98] B. Slepetz, I. Laszlo, Y. Gogotsi, D. Hyde-Volpe, M. Kertesz, Characterization of large vacancy clusters in diamond from a generational algorithm using tight binding density functional theory, Physical Chemistry Chemical Physics 12(42) (2010) 14017-14022. ##[99] P. Neumann, J. Beck, M. Steiner, F. Rempp, H. Fedder, P.R. Hemmer, J. Wrachtrup, F. Jelezko, Single-shot readout of a single nuclear spin, Science 329(5991) (2010) 542-544. ##[100] J.R. Maze, P.L. Stanwix, J.S. Hodges, S. Hong, J.M. Taylor, P. Cappellaro, L. Jiang, M.G. Dutt, E. Togan, A. Zibrov, Nanoscale magnetic sensing with an individual electronic spin in diamond, Nature 455(7213) (2008) 644-647. ##[101] G. Balasubramanian, I. Chan, R. Kolesov, M. Al-Hmoud, J. Tisler, C. Shin, C. Kim, A. Wojcik, P.R. Hemmer, A. Krueger, Nanoscale imaging magnetometry with diamond spins under ambient conditions, Nature 455(7213) (2008) 648-651. ##[102] C. Bradac, T. Gaebel, N. Naidoo, M. Sellars, J. Twamley, L. Brown, A. Barnard, T. Plakhotnik, A. Zvyagin, J. Rabeau, Observation and control of blinking nitrogen-vacancy centres in discrete nanodiamonds, Nature nanotechnology 5(5) (2010) 345-349. ##[103] J. Tisler, R. Reuter, A. Lämmle, F. Jelezko, G. Balasubramanian, P.R. Hemmer, F. Reinhard, J.r. Wrachtrup, Highly efficient FRET from a single nitrogen-vacancy center in nanodiamonds to a single organic molecule, Acs Nano 5(10) (2011) 7893-7898. ##[104] J. Tisler, G. Balasubramanian, B. Naydenov, R. Kolesov, B. Grotz, R. Reuter, J.-P. Boudou, P.A. Curmi, M. Sennour, A. Thorel, Fluorescence and spin properties of defects in single digit nanodiamonds, ACS nano 3(7) (2009) 1959-1965. ##[105] A. Sanaat, H. Arabi, I. Mainta, V. Garibotto, H. Zaidi, Projection Space Implementation of Deep Learning-Guided Low-Dose Brain PET Imaging Improves Performance over Implementation in Image Space, Journal of nuclear medicine : official publication, Society of Nuclear Medicine 61(9) (2020) 1388-1396. ##[106] A. Sanaat, H. Arabi, M.R. Ay, H. Zaidi, Novel preclinical PET geometrical concept using a monolithic scintillator crystal offering concurrent enhancement in spatial resolution and detection sensitivity: a simulation study, Physics in Medicine and Biology 65(4) (2020) 045013. ##[107] A. Sanaat, H. Zaidi, Depth of interaction estimation in a preclinical PET scanner equipped with monolithic crystals coupled to SiPMs using a deep neural network, Applied Sciences 10(14) (2020) 4753. ##[108] A. Sanaat, A. Ashrafi-Belgabad, H. Zaidi, Polaroid-PET: a PET scanner with detectors fitted with polaroids for filtering unpolarized optical photons: a Monte Carlo simulation study, Physics in Medicine and Biology (2020). ##[109] O.A. Shenderova, I.I. Vlasov, S. Turner, G. Van Tendeloo, S.B. Orlinskii, A.A. Shiryaev, A.A. Khomich, S.N. Sulyanov, F. Jelezko, J. Wrachtrup, Nitrogen control in nanodiamond produced by detonation shock-wave-assisted synthesis, The Journal of Physical Chemistry C 115(29) (2011) 14014-14024. ##[110] I.I. Vlasov, O. Shenderova, S. Turner, O.I. Lebedev, A.A. Basov, I. Sildos, M. Rähn, A.A. Shiryaev, G. Van Tendeloo, Nitrogen and luminescent nitrogen‐vacancy defects in detonation nanodiamond, Small 6(5) (2010) 687-694. ##[111] L.-C.L. Huang, H.-C. Chang, Adsorption and immobilization of cytochrome c on nanodiamonds, Langmuir 20(14) (2004) 5879-5884. ##[112] S.C. Hens, G. Cunningham, T. Tyler, S. Moseenkov, V. Kuznetsov, O. Shenderova, Nanodiamond bioconjugate probes and their collection by electrophoresis, Diamond and related materials 17(11) (2008) 1858-1866. ##[113] A.M. Schrand, J.B. Lin, S.C. Hens, S.M. Hussain, Temporal and mechanistic tracking of cellular uptake dynamics with novel surface fluorophore-bound nanodiamonds, Nanoscale 3(2) (2011) 435-445. ##[114] V.N. Mochalin, Y. Gogotsi, Wet chemistry route to hydrophobic blue fluorescent nanodiamond, Journal of the American Chemical Society 131(13) (2009) 4594-4595. ##[115] O. Faklaris, V. Joshi, T. Irinopoulou, P. Tauc, M. Sennour, H. Girard, C. Gesset, J.-C. Arnault, A. Thorel, J.-P. Boudou, Photoluminescent diamond nanoparticles for cell labeling: study of the uptake mechanism in mammalian cells, ACS nano 3(12) (2009) 3955-3962. ##[116] L.P. McGuinness, Y. Yan, A. Stacey, D.A. Simpson, L.T. Hall, D. Maclaurin, S. Prawer, P. Mulvaney, J. Wrachtrup, F. Caruso, Quantum measurement and orientation tracking of fluorescent nanodiamonds inside living cells, Nature nanotechnology 6(6) (2011) 358-363. ##[117] X.Q. Zhang, R. Lam, X. Xu, E.K. Chow, H.J. Kim, D. Ho, Multimodal nanodiamond drug delivery carriers for selective targeting, imaging, and enhanced chemotherapeutic efficacy, Advanced materials 23(41) (2011) 4770-4775. ##[118] J. Dong, R. Jiang, H. Huang, J. Chen, J. Tian, F. Deng, Y. Dai, Y. Wen, X. Zhang, Y. Wei, Facile preparation of fluorescent nanodiamond based polymer nanoparticles via ring-opening polymerization and their biological imaging, Materials Science and Engineering: C 106 (2020) 110297. ##[119] Wide-field in vivo background free imaging by selective magnetic modulation of nanodiamond fluorescence, Biomed. Opt. Express 5(4) (2014) 1190-1202. ##[120] A. Schrand, J. Johnson, L. Dai, S.M. Hussain, J. Schlager, L. Zhu, Y. Hong, E. Osawa, Safety of Nanoparticles, From Manufacturing to Medical Applications, Nanostructure Science and Technology (2009) 159-187. ##[121] J. Kowalczyk, M. Madej, D. Ozimina, K. Milewski, The influence of non-toxic cutting fluid on the diamond-like carbon coatings, AIP Conference Proceedings, AIP Publishing LLC, 2018, p. 020009. ##[122] K.-H. Yang, R.J. Narayan, Biocompatibility and functionalization of diamond for neural applications, Current Opinion in Biomedical Engineering 10 (2019) 60-68. ##[123] Q. Zhang, V.N. Mochalin, I. Neitzel, I.Y. Knoke, J. Han, C.A. Klug, J.G. Zhou, P.I. Lelkes, Y. Gogotsi, Fluorescent PLLA-nanodiamond composites for bone tissue engineering, Biomaterials 32(1) (2011) 87-94. ##[124] A.M. Schrand, H. Huang, C. Carlson, J.J. Schlager, E. Ōsawa, S.M. Hussain, L. Dai, Are diamond nanoparticles cytotoxic?, The journal of physical chemistry B 111(1) (2007) 2-7. ##[125] Y. Yuan, X. Wang, G. Jia, J.-H. Liu, T. Wang, Y. Gu, S.-T. Yang, S. Zhen, H. Wang, Y. Liu, Pulmonary toxicity and translocation of nanodiamonds in mice, Diamond and Related Materials 19(4) (2010) 291-299. ##[126] N. Mohan, C.-S. Chen, H.-H. Hsieh, Y.-C. Wu, H.-C. Chang, In vivo imaging and toxicity assessments of fluorescent nanodiamonds in Caenorhabditis elegans, Nano letters 10(9) (2010) 3692-3699. ##[127] E.K. Chow, X.-Q. Zhang, M. Chen, R. Lam, E. Robinson, H. Huang, D. Schaffer, E. Osawa, A. Goga, D. Ho, Nanodiamond therapeutic delivery agents mediate enhanced chemoresistant tumor treatment, Science translational medicine 3(73) (2011) 73ra21-73ra21. ##[128] K. Yonezawa, M. Kawaguchi, A. Kaneuji, T. Ichiseki, Y. Iinuma, K. Kawamura, K. Shintani, S. Oda, M. Taki, N. Kawahara, Evaluation of Antibacterial and Cytotoxic Properties of a Fluorinated Diamond-Like Carbon Coating for the Development of Antibacterial Medical Implants, Antibiotics 9(8) (2020) 495. ##[129] L. Moore, J. Yang, T.T.H. Lan, E. Osawa, D.-K. Lee, W.D. Johnson, J. Xi, E.K.-H. Chow, D. Ho, Biocompatibility assessment of detonation nanodiamond in non-human primates and rats using histological, hematologic, and urine analysis, ACS nano 10(8) (2016) 7385-7400. ##[130] S. Kurtz, S. Kurtz, A Primer on UHMWPE UHMWPE biomaterials handbook: ultra high molecular weight polyethylene in total joint replacement and medical devices, Boston: Elsevier/Academic Press, 2009. ##[131] Z. Karaguiozova, J. Kaleicheva, V. Mishev, G. Nikolcheva, Enhancement in the Tribological and Mechanical Properties of Electroless Nickel-Nanodiamond Coatings Plated on Iron, Tribology in Industry 39(4) (2017). ##[132] T. Takimoto, T. Chano, S. Shimizu, H. Okabe, M. Ito, M. Morita, T. Kimura, T. Inubushi, N. Komatsu, Preparation of fluorescent diamond nanoparticles stably dispersed under a physiological environment through multistep organic transformations, Chemistry of materials 22(11) (2010) 3462-3471. ##[133] O. Shenderova, N. Nunn, T. Oeckinghaus, M. Torelli, G. McGuire, K. Smith, E. Danilov, R. Reuter, J. Wrachtrup, A. Shames, Commercial quantities of ultrasmall fluorescent nanodiamonds containing color centers, Advances in Photonics of Quantum Computing, Memory, and Communication X, International Society for Optics and Photonics, 2017, p. 1011803. ##[134] L. Joly-Pottuz, N. Matsumoto, H. Kinoshita, B. Vacher, M. Belin, G. Montagnac, J. Martin, N. Ohmae, Diamond-derived carbon onions as lubricant additives, Tribology International 41(2) (2008) 69-78. ##[135] V.N. Mochalin, O. Shenderova, D. Ho, Y. Gogotsi, The properties and applications of nanodiamonds, Nature nanotechnology 7(1) (2012) 11-23. ##[136] L. Bazli, A. Khavandi, M.A. Boutorabi, M. Karrabi, Correlation between viscoelastic behavior and morphology of nanocomposites based on SR/EPDM blends compatibilized by maleic anhydride, Polymer 113 (2017) 156-166. ##[137] L. Bazli, A. Khavandi, M.A. Boutorabi, M. Karrabi, Morphology and viscoelastic behavior of silicone rubber/EPDM/Cloisite 15A nanocomposites based on Maxwell model, Iranian Polymer Journal 25(11) (2016) 907-918. ##[138] S. Saadi, B. Nazari, Recent developments and applications of nanocomposites in solar cells: a review, Journal of Composites and Compounds 1(1) (2019) 48-58. ##[139] H.W. Jang, A. Zareidoost, M. Moradi, A. Abuchenari, A. Bakhtiari, R. Pouriamanesh, B. Malekpouri, A.J. Rad, D. Rahban, Photosensitive nanocomposites: environmental and biological applications, Journal of Composites and Compounds 2(1) (2020) 50-60. ##[140] O. Shenderova, A. Panich, S. Moseenkov, S. Hens, V. Kuznetsov, H.-M. Vieth, Hydroxylated detonation nanodiamond: FTIR, XPS, and NMR studies, The Journal of Physical Chemistry C 115(39) (2011) 19005-19011. ##[141] W. Ma, X. Yu, X. Qu, Q. Zhang, Functionalization of agglomerating nanodiamonds with biodegradable poly (ε-caprolactone) through surface-initiated polymerization, Diamond and Related Materials 62 (2016) 14-21. ##[142] A. Krüger, Y. Liang, G. Jarre, J. Stegk, Surface functionalisation of detonation diamond suitable for biological applications, Journal of Materials Chemistry 16(24) (2006) 2322-2328. ##[143] J. Nunes-Pereira, A. Silva, C. Ribeiro, S. Carabineiro, J. Buijnsters, S. Lanceros-Méndez, Nanodiamonds/poly (vinylidene fluoride) composites for tissue engineering applications, Composites Part B: Engineering 111 (2017) 37-44. ##[144] Y. Sun, Q. Yang, H. Wang, Synthesis and characterization of nanodiamond reinforced chitosan for bone tissue engineering, Journal of functional biomaterials 7(3) (2016) 27. ##[145] A. Stacey, I. Aharonovich, S. Prawer, J.E. Butler, Controlled synthesis of high quality micro/nano-diamonds by microwave plasma chemical vapor deposition, Diamond and related materials 18(1) (2009) 51-55. ##[146] V.N. Mochalin, Y. Gogotsi, Nanodiamond–polymer composites, Diamond and Related Materials 58 (2015) 161-171. ##[147] D. Wang, Y. Tong, Y. Li, Z. Tian, R. Cao, B. Yang, PEGylated nanodiamond for chemotherapeutic drug delivery, Diamond and related materials 36 (2013) 26-34. ##[148] K. Fox, P.A. Tran, D.W. Lau, T. Ohshima, A.D. Greentree, B.C. Gibson, Nanodiamond-polycaprolactone composite: A new material for tissue engineering with sub-dermal imaging capabilities, Materials Letters 185 (2016) 185-188. ##[149] A.D. Salaam, M. Mishra, E. Nyairo, D. Dean, Electrospun polyvinyl alcohol/nanodiamond composite scaffolds: morphological, structural, and biological analysis, Journal of biomaterials and tissue engineering 4(3) (2014) 173-180. ##[150] H. Gomez, M.K. Ram, F. Alvi, E. Stefanakos, A. Kumar, Novel synthesis, characterization, and corrosion inhibition properties of nanodiamond− polyaniline films, The Journal of Physical Chemistry C 114(44) (2010) 18797-18804. ##[151] L. Cao, Y. Hou, K. Lafdi, K. Urmey, Fluorescent composite scaffolds made of nanodiamonds/polycaprolactone, Chemical Physics Letters 641 (2015) 123-128. ##[152] M. Abniki, A. Moghimi, F. Azizinejad, Fabrication of bionanocomposite based on LDH using biopolymer of gum arabic and chitosan-coating for sustained drug-release, Journal of the Serbian Chemical Society 85(5) (2020). ##[153] M. Abniki, A. Moghimi, F. Azizinejad, Synthesis of calcium‐layered double hydroxide based nanohybrid for controlled release of an anti‐inflammatory drug, Journal of the Chinese Chemical Society (2020). ##[154] A. Bakhtiari, A. Cheshmi, M. Naeimi, S.M. Fathabad, M. Aliasghari, A.M. Chahardehi, S. Hassani, V. Elhami, Synthesis and characterization of the novel 80S bioactive glass: bioactivity,‎ biocompatibility, cytotoxicity, Journal of Composites and Compounds 2(4) (2020) 110-114. ##[155] B.F. Dizaji, M.H. Azerbaijan, N. Sheisi, P. Goleij, T. Mirmajidi, F. Chogan, M. Irani, F. Sharafian, Synthesis of PLGA/chitosan/zeolites and PLGA/chitosan/metal organic frameworks nanofibers for targeted delivery of Paclitaxel toward prostate cancer cells death, International Journal of Biological Macromolecules 164 (2020) 1461-1474. ##[156] A. Nouri, B. Faraji Dizaji, N. Kianinejad, A. Jafari Rad, S. Rahimi, M. Irani, F. Sharifian Jazi, Simultaneous linear release of folic acid and doxorubicin from ethyl cellulose/chitosan/g‐C3N4/MoS2 core‐shell nanofibers and its anticancer properties, Journal of Biomedical Materials Research Part A (2020). ##[157] N. Nunn, M. Torelli, G. McGuire, O. Shenderova, Nanodiamond: a high impact nanomaterial, Current Opinion in Solid State and Materials Science 21(1) (2017) 1-9. ##[158] T. Kondo, I. Neitzel, V.N. Mochalin, J. Urai, M. Yuasa, Y. Gogotsi, Electrical conductivity of thermally hydrogenated nanodiamond powders, Journal of Applied Physics 113(21) (2013) 214307. ##[159] S. Mukhopadhyay, B. Deopura, High-modulus polypropylene fibers—through postspinning operations, Structure and Properties of High-Performance Fibers, Elsevier2017, pp. 187-198. ##[160] M. Mahdavi, N. Mahmoudi, F. Rezaie Anaran, A. Simchi, Electrospinning of nanodiamond-modified polysaccharide nanofibers with physico-mechanical properties close to natural skins, Marine drugs 14(7) (2016) 128. ##[161] N. Cai, Q. Dai, Z. Wang, X. Luo, Y. Xue, F. Yu, Preparation and properties of nanodiamond/poly (lactic acid) composite nanofiber scaffolds, Fibers and Polymers 15(12) (2014) 2544-2552. ##[162] J. Xiao, X. Duan, Q. Yin, Z. Zhang, H. Yu, Y. Li, Nanodiamonds-mediated doxorubicin nuclear delivery to inhibit lung metastasis of breast cancer, Biomaterials 34(37) (2013) 9648-9656. ##[163] T.-F. Li, K. Li, Q. Zhang, C. Wang, Y. Yue, Z. Chen, S.-J. Yuan, X. Liu, Y. Wen, M. Han, Dendritic cell-mediated delivery of doxorubicin-polyglycerol-nanodiamond composites elicits enhanced anti-cancer immune response in glioblastoma, Biomaterials 181 (2018) 35-52. ##[164] A.N. Bokarev, I.L. Plastun, Possibility of drug delivery due to hydrogen bonds formation in nanodiamonds and doxorubicin: molecular modeling, Наносистемы: физика, химия, математика 9(3) (2018). ##[165] M. Radmansouri, E. Bahmani, E. Sarikhani, K. Rahmani, F. Sharifianjazi, M. Irani, Doxorubicin hydrochloride-Loaded electrospun chitosan/cobalt ferrite/titanium oxide nanofibers for hyperthermic tumor cell treatment and controlled drug release, International journal of biological macromolecules 116 (2018) 378-384. ##[166] P. Abasian, M. Radmansouri, M.H. Jouybari, M.V. Ghasemi, A. Mohammadi, M. Irani, F.S. Jazi, Incorporation of magnetic NaX zeolite/DOX into the PLA/chitosan nanofibers for sustained release of doxorubicin against carcinoma cells death in vitro, International journal of biological macromolecules 121 (2019) 398-406. ##[167] J.W. Rhim, A.K. Mohanty, S.P. Singh, P.K. Ng, Effect of the processing methods on the performance of polylactide films: Thermocompression versus solvent casting, Journal of applied polymer science 101(6) (2006) 3736-3742. ##[168] N. Bhardwaj, S.C. Kundu, Electrospinning: a fascinating fiber fabrication technique, Biotechnology advances 28(3) (2010) 325-347. ##[169] U. Roy, V. Drozd, A. Durygin, J. Rodriguez, P. Barber, V. Atluri, X. Liu, T.G. Voss, S. Saxena, M. Nair, Characterization of Nanodiamond-based anti-HIV drug Delivery to the Brain, Scientific reports 8(1) (2018) 1-12. ##[170] M.H. Alkahtani, F. Alghannam, L. Jiang, A. Almethen, A.A. Rampersaud, R. Brick, C.L. Gomes, M.O. Scully, P.R. Hemmer, Fluorescent nanodiamonds: past, present, and future, Nanophotonics 7(8) (2018) 1423-1453. ##[171] J. Liu, L. Cui, D. Losic, Graphene and graphene oxide as new nanocarriers for drug delivery applications, Acta biomaterialia 9(12) (2013) 9243-9257. ##[172] P. Chandrasekhar, CNT applications in drug and biomolecule delivery, Conducting Polymers, Fundamentals and Applications, Springer2018, pp. 61-64. ##[173] H. Girard, T. Petit, S. Perruchas, T. Gacoin, C. Gesset, J.-C. Arnault, P. Bergonzo, Surface properties of hydrogenated nanodiamonds: a chemical investigation, Physical chemistry chemical physics 13(24) (2011) 11517-11523. ##[174] S. Nasibi, K. Alimohammadi, L. Bazli, S. Eskandarinezhad, A. Mohammadi, N. Sheysi, TZNT alloy for surgical implant applications: A systematic review, Journal of Composites and Compounds 2(3) (2020) 62-68. ##[175] Z. Goudarzi, A. Ijadi, A. Bakhtiari, S. Eskandarinezhad, N. Azizabadi, M.A. Jazi, Sr-doped bioactive glasses for biological applications, Journal of Composites and Compounds 2(3) (2020) 105-109. ##[176] J. Daraei, Production and characterization of PCL (Polycaprolactone) coated TCP/nanoBG composite scaffolds by sponge foam method for orthopedic applications, Journal of Composites and Compounds 2(1) (2020) 45-50. ##[177] K. Fox, R. Ratwatte, M.A. Booth, H.M. Tran, P.A. Tran, High Nanodiamond Content-PCL Composite for Tissue Engineering Scaffolds, Nanomaterials 10(5) (2020) 948. ##[178] O.S. Adeyemi, F.A. Sulaiman, Evaluation of metal nanoparticles for drug delivery systems, Journal of biomedical research 29(2) (2015) 145. ##[179] P. Karami, S.S. Khasraghi, M. Hashemi, S. Rabiei, A. Shojaei, Polymer/nanodiamond composites-a comprehensive review from synthesis and fabrication to properties and applications, Advances in Colloid and Interface Science 269 (2019) 122-151. ##[180] Q. Zhang, I. Neitzel, V.N. Mochalin, I. Knoke, D.M. Wootton, Y. Gogotsi, P.I. Lelkes, J.G. Zhou, PLLA-nanodiamond composites and their application in bone tissue engineering, Global Congress on NanoEngineering for Medicine and Biology, 2010, pp. 241-242. ##[181] X. Xu, X. Wang, L. Yang, H. Yu, H. Chang, Structure and surface characterization of co-adsorbed layer of oleic acid and octadecylamine on detonation nanodiamond, Diamond and Related Materials 60 (2015) 50-59. ##[182] P. Feng, Y. Kong, L. Yu, Y. Li, C. Gao, S. Peng, H. Pan, Z. Zhao, C. Shuai, Molybdenum disulfide nanosheets embedded with nanodiamond particles: co-dispersion nanostructures as reinforcements for polymer scaffolds, Applied Materials Today 17 (2019) 216-226. ##[183] T.C. Yadav, A.K. Srivastava, P. Mishra, D. Singh, N. Raghuwanshi, N.K. Singh, A.K. Singh, S.K. Tiwari, R. Prasad, V. Pruthi, Electrospinning: An Efficient Biopolymer-Based Micro-and Nanofibers Fabrication Technique, Next Generation Biomanufacturing Technologies, ACS Publications2019, pp. 209-241. ##[184] B. Pant, M. Park, S.-J. Park, Drug delivery applications of core-sheath nanofibers prepared by coaxial electrospinning: a review, Pharmaceutics 11(7) (2019) 305. ##[185] I. Jun, H.-S. Han, J.R. Edwards, H. Jeon, Electrospun fibrous scaffolds for tissue engineering: Viewpoints on architecture and fabrication, International journal of molecular sciences 19(3) (2018) 745. ##[186] F. Pereira, G. Salles, B. Rodrigues, F. Marciano, C. Pacheco-Soares, A. Lobo, Diamond nanoparticles into poly (lactic acid) electrospun fibers: Cytocompatible and bioactive scaffolds with enhanced wettability and cell adhesion, Materials Letters 183 (2016) 420-424. ##[187] S. Houshyar, G.S. Kumar, A. Rifai, N. Tran, R. Nayak, R.A. Shanks, R. Padhye, K. Fox, A. Bhattacharyya, Nanodiamond/poly-ε-caprolactone nanofibrous scaffold for wound management, Materials Science and Engineering: C 100 (2019) 378-387. ##[188] L. Bazli, B. Eftekhari Yekta, A. Khavandi, Preparation and Characterization of Sn-Containing Glasses for Brachytherapy Applications, Transactions of the Indian Ceramic Society 76(4) (2017) 242-246. ##[189] M.A. Brady, A. Renzing, T.E. Douglas, Q. Liu, S. Wille, M. Parizek, L. Bacakova, A. Kromka, M. Jarosova, G. Godier, Development of composite poly (lactide-co-glycolide)-nanodiamond scaffolds for bone cell growth, Journal of nanoscience and nanotechnology 15(2) (2015) 1060-1069. ##[190] M. Parizek, T.E. Douglas, K. Novotna, A. Kromka, M.A. Brady, A. Renzing, E. Voss, M. Jarosova, L. Palatinus, P. Tesarek, Nanofibrous poly (lactide-co-glycolide) membranes loaded with diamond nanoparticles as promising substrates for bone tissue engineering, International journal of nanomedicine 7 (2012) 1931. ##[191] V. Kumar, R. Mahajan, I. Kaur, K.-H. Kim, Simple and mediator-free urea sensing based on engineered nanodiamonds with polyaniline nanofibers synthesized in situ, ACS Applied Materials and Interfaces 9(20) (2017) 16813-16823. ##[192] M. Alishiri, A. Shojaei, M.J. Abdekhodaie, Biodegradable polyurethane acrylate/HEMA-grafted nanodiamond composites with bone regenerative potential applications: structure, mechanical properties and biocompatibility, RSC advances 6(11) (2016) 8743-8755. ##[193] S.A. Haddadi, A.R. SA, M. Amini, A. Kheradmand, In-situ preparation and characterization of ultra-high molecular weight polyethylene/diamond nanocomposites using Bi-supported Ziegler-Natta catalyst: Effect of nanodiamond silanization, Materials Today Communications 14 (2018) 53-64. ##[194] J. Nunes-Pereira, A.R. Silva, C. Ribeiro, S.A.C. Carabineiro, J.G. Buijnsters, S. Lanceros-Méndez, Nanodiamonds/poly(vinylidene fluoride) composites for tissue engineering applications, Composites Part B: Engineering 111 (2017) 37-44. ##[195] U. Maitra, K.E. Prasad, U. Ramamurty, C.N.R. Rao, Mechanical properties of nanodiamond-reinforced polymer-matrix composites, Solid State Communications 149(39) (2009) 1693-1697. ##[196] U. Maitra, K.E. Prasad, U. Ramamurty, C. Rao, Mechanical properties of nanodiamond-reinforced polymer-matrix composites, Solid State Communications 149(39-40) (2009) 1693-1697. ##[197] O. Shenderova, T. Tyler, G. Cunningham, M. Ray, J. Walsh, M. Casulli, S. Hens, G. McGuire, V. Kuznetsov, S. Lipa, Nanodiamond and onion-like carbon polymer nanocomposites, Diamond and related materials 16(4-7) (2007) 1213-1217. ##[198] E. Tamburri, V. Guglielmotti, S. Orlanducci, M.L. Terranova, D. Sordi, D. Passeri, R. Matassa, M. Rossi, Nanodiamond-mediated crystallization in fibers of PANI nanocomposites produced by template-free polymerization: Conductive and thermal properties of the fibrillar networks, Polymer 53(19) (2012) 4045-4053. ##[199] A. Apicella, R. Aversa, F.I. Petrescu, Hybrid Ceramo-Polymeric Nano-Diamond Composites, American Journal of Engineering and Applied Sciences 11(2) (2018) 766.782. ##[200] L. Wang, W. Cao, X. Wang, P. Li, J. Zhou, G. Zhang, X. Li, X. Xing, Biodegradable silver-loaded polycation modified nanodiamonds/polyurethane scaffold with improved antibacterial and mechanical properties for cartilage tissue repairing, Journal of Materials Science: Materials in Medicine 30(4) (2019) 41. ##[201] C. Shuai, W. Huang, P. Feng, C. Gao, D. Gao, Y. Deng, Q. Wang, P. Wu, X. Guo, Nanodiamond reinforced polyvinylidene fluoride/bioglass scaffolds for bone tissue engineering, Journal of Porous Materials 24(1) (2017) 249-255. ##[202] S. Balakin, Y.-S. Yun, J. Lee, E.-H. Kang, J. Spohn, I.-S. Yun, J. Opitz, G. Cuniberti, J.-S. Yeo, In vitro characterization of osteoblast cells on polyelectrolyte multilayers containing detonation nanodiamonds, Biomedical Materials (2020). ##[203] H. Gong, B. Anasori, C.R. Dennison, K. Wang, E.C. Kumbur, R. Strich, J.G. Zhou, Fabrication, biodegradation behavior and cytotoxicity of Mg-nanodiamond composites for implant application, Journal of Materials Science: Materials in Medicine 26(2) (2015) 110. ##[204] Q. Zhang, V.N. Mochalin, I. Neitzel, K. Hazeli, J. Niu, A. Kontsos, J.G. Zhou, P.I. Lelkes, Y. Gogotsi, Mechanical properties and biomineralization of multifunctional nanodiamond-PLLA composites for bone tissue engineering, Biomaterials 33(20) (2012) 5067-5075. ##[205] G.Y. Ahn, T.-K. Ryu, Y.R. Choi, J.R. Park, M.J. Lee, S.-W. Choi, Fabrication and optimization of Nanodiamonds-composited poly (ε-caprolactone) fibrous matrices for potential regeneration of hard tissues, Biomaterials research 22(1) (2018) 1-8. ##[206] Y. Sun, A. Finne‐Wistrand, T. Waag, Z. Xing, M. Yassin, A. Yamamoto, K. Mustafa, D. Steinmüller‐Nethl, A. Krueger, A.C. Albertsson, Reinforced degradable biocomposite by homogenously distributed functionalized nanodiamond particles, Macromolecular Materials and Engineering 300(4) (2015) 436-447. ##[207] A. Şelaru, D.-M. Drăgușin, E. Olăreț, A. Serafim, D. Steinmüller-Nethl, E. Vasile, H. Iovu, I.-C. Stancu, M. Costache, S. Dinescu, Fabrication and biocompatibility evaluation of nanodiamonds-gelatin electrospun materials designed for prospective tissue regeneration applications, Materials 12(18) (2019) 2933.##

1 - Application of composite conducting polymers for improving the corrosion behavior of various substrates: A Review https://www.jourcc.com/index.php/jourcc/article/view/jcc247 10.29252/jcc.2.4.7 1 One of the most important problems in the manufacturing industry is metal corrosion. Recently, conductive polymers (CPs) have attracted attention due to their economic viability and widespread industrial applications. Upon adsorption, long-chain carbon bonds of polymers provide a blockage for large surface areas of corroding metals. The adsorbed thin films create a barrier between the surrounding environment and the metal substrate. Polypyrrole (PPy), polyaniline (PANI), and polythiophene (PTh) are conducting polymers that are utilized to protect metals and metal alloys against corrosion. A proper selection of synthesis parameters for CPs can improve the anticorrosion behavior of the coatings for metals and metal alloys. This paper has an overview of conducting polymer composite coatings on substrates based on steel, copper, magnesium, aluminum, and their alloys. 0 - 228 240 - - Leila Bazli School of Metallurgy and Materials Engineering, Iran University of Science and Technology Iran leilabazli64@gmail.com - - Mohammad Yusuf Department of Chemical Engineering, Universiti Teknologi PETRONAS Malaysia info@jourcc.com - - Ali Farahani Department of Textile Engineering, Amirkabir University of Technology Iran info@jourcc.com - - Morvarid Kiamarzi Department of Polymer Engineering and Color Technology, Amirkabir University of Technology Iran info@jourcc.com - - Zahra Seyedhosseini Department of Chemistry, Amirkabir University of Technology Iran info@jourcc.com - - Mehran Nezhadmansari Department of Engineering and Materials Science, Sharif University of Technology Iran info@jourcc.com - - Maryam Aliasghari Department of Chemistry, Yadegar-e-Imam Khomeini (RAH) Shahre Rey Branch, Islamic Azad University Iran info@jourcc.com - - Marjan Iranpoor Department of Agricultural Machinery Mechanics, University of Tehran Iran info@jourcc.com Corrosion resistance Polyaniline Polypyrrole Polythiophene Metal substrates [1] B. Yao, G. Wang, J. Ye, X. Li, Corrosion inhibition of carbon steel by polyaniline nanofibers, Materials Letters 62(12-13) (2008) 1775-1778. ##[2] M. Hosseini, M. Sabouri, T. Shahrabi, Corrosion protection of mild steel by polypyrrole phosphate composite coating, Progress in Organic Coatings 60(3) (2007) 178-185. ##[3] S. Das, T. Yokozeki, Polyaniline-based multifunctional glass fiber reinforced conductive composite for strain monitoring, Polymer Testing (2020) 106547. ##[4] P. Herrasti, F. Recio, P. Ocon, E. Fatás, Effect of the polymer layers and bilayers on the corrosion behaviour of mild steel: Comparison with polymers containing Zn microparticles, Progress in Organic Coatings 54(4) (2005) 285-291. ##[5] S. Das, S. Sharma, T. Yokozeki, S. Dhakate, Conductive Layer-based Multifunctional Structural Composites for Electromagnetic Interference Shielding, Composite Structures (2020) 113293. ##[6] V. Kumar, S. Das, T. Yokozeki, Frequency independent AC electrical conductivity and dielectric properties of polyaniline-based conductive thermosetting composite, Journal of Polymer Engineering 38(10) (2018) 955-961. ##[7] H. Zhu, L. Zhong, S. Xiao, F. Gan, Accelerating effect and mechanism of passivation of polyaniline on ferrous metals, Electrochimica acta 49(28) (2004) 5161-5166. ##[8] S. Aeiyach, B. Zaid, P. Lacaze, A one-step electrosynthesis of PPy films on zinc substrates by anodic polymerization of pyrrole in aqueous solution, Electrochimica acta 44(17) (1999) 2889-2898. ##[9] T. Zhang, C. Zeng, Corrosion protection of 1Cr18Ni9Ti stainless steel by polypyrrole coatings in HCl aqueous solution, Electrochimica Acta 50(24) (2005) 4721-4727. ##[10] G.M. Spinks, A.J. Dominis, G.G. Wallace, D.E. Tallman, Electroactive conducting polymers for corrosion control, Journal of Solid State Electrochemistry 6(2) (2002) 85-100. ##[11] N. Ogurtsov, A. Pud, P. Kamarchik, G. Shapoval, Corrosion inhibition of aluminum alloy in chloride mediums by undoped and doped forms of polyaniline, Synthetic Metals 143(1) (2004) 43-47. ##[12] K. Shah, J. Iroh, Electrochemical synthesis and corrosion behavior of poly (N-ethyl aniline) coatings on Al-2024 alloy, Synthetic metals 132(1) (2002) 35-41. ##[13] A.R. Elkais, M.M. Gvozdenović, B. Jugović, T. Trišović, M. Maksimović, B. Grgur, Electrochemical synthesis and corrosion behavior of thin polyaniline film on mild steel, copper and aluminum, Hemijska industrija 65(1) (2011) 15-21. ##[14] J. Martins, M. Bazzaoui, T. Reis, E. Bazzaoui, L. Martins, Electrosynthesis of homogeneous and adherent polypyrrole coatings on iron and steel electrodes by using a new electrochemical procedure, Synthetic metals 129(3) (2002) 221-228. ##[15] S. Jafarzadeh, P.M. Claesson, P.-E. Sundell, E. Tyrode, J. Pan, Active corrosion protection by conductive composites of polyaniline in a UV-cured polyester acrylate coating, Progress in organic coatings 90 (2016) 154-162. ##[16] A. Ali Fathima Sabirneeza, S. Subhashini, A novel water‐soluble, conducting polymer composite for mild steel acid corrosion inhibition, Journal of applied polymer science 127(4) (2013) 3084-3092. ##[17] J. Stejskal, M. Trchová, J. Kovářová, J. Prokeš, M. Omastová, Polyaniline-coated cellulose fibers decorated with silver nanoparticles, Chemical Papers 62(2) (2008) 181-186. ##[18] S.S. Najar, A. Kaynak, R.C. Foitzik, Conductive wool yarns by continuous vapour phase polymerization of pyrrole, Synthetic metals 157(1) (2007) 1-4. ##[19] S.A. Kumar, K.S. Meenakshi, T. Sankaranarayanan, S. Srikanth, Corrosion resistant behaviour of PANI–metal bilayer coatings, Progress in Organic Coatings 62(3) (2008) 285-292. ##[20] T. Li, X. Zeng, J. Xu, Preparation and characterization of conductive polypyrrole/organophilic montorillonite nanocomposite, Polymer-Plastics Technology and Engineering 46(8) (2007) 751-757. ##[21] S. Das, V. Kumar, T. Yokozeki, Strain sensing behavior of multifunctional polyaniline-based thermoset polymer under static loading conditions, Polymer Testing 77 (2019) 105916. ##[22] T.F. Otero, Conducting Polymers: Bioinspired Intelligent Materials and Devices, Royal Society of Chemistry2016. ##[23] I. György, Conducting polymers: A new era in electrochemistry, Springer2008. ##[24] Z. Chen, G. Zhang, W. Yang, B. Xu, Y. Chen, X. Yin, Y. Liu, Superior conducting polypyrrole anti-corrosion coating containing functionalized carbon powders for 304 stainless steel bipolar plates in proton exchange membrane fuel cells, Chemical Engineering Journal (2020) 124675. ##[25] M. Bouabdallaoui, Z. Aouzal, A. El Guerraf, S.B. Jadi, M. Bazzaoui, R. Wang, E. Bazzaoui, Influence of polythiophene overoxidation on its physicochemical properties and corrosion protection performances, Materials Today: Proceedings 31 (2020) S69-S74. ##[26] S. Shi, Y. Zhao, Z. Zhang, L. Yu, Corrosion protection of a novel SiO2@ PANI coating for Q235 carbon steel, Progress in Organic Coatings 132 (2019) 227-234. ##[27] G. Inzelt, Conducting polymers: a new era in electrochemistry, Springer Science and Business Media2012. ##[28] G. Ćirić-Marjanović, Recent advances in polyaniline research: Polymerization mechanisms, structural aspects, properties and applications, Synthetic metals 177 (2013) 1-47. ##[29] B. Bhanvase, S. Sonawane, New approach for simultaneous enhancement of anticorrosive and mechanical properties of coatings: Application of water repellent nano CaCO3–PANI emulsion nanocomposite in alkyd resin, Chemical Engineering Journal 156(1) (2010) 177-183. ##[30] X. Tan, C. Hu, Z. Zhu, H. Liu, J. Qu, Electrically Pore‐Size‐Tunable Polypyrrole Membrane for Antifouling and Selective Separation, Advanced Functional Materials 29(35) (2019) 1903081. ##[31] V.K. Thakur, G. Ding, J. Ma, P.S. Lee, X. Lu, Hybrid materials and polymer electrolytes for electrochromic device applications, Advanced materials 24(30) (2012) 4071-4096. ##[32] I. Sultana, M. Rahman, S. Li, J. Wang, C. Wang, G.G. Wallace, H.-K. Liu, Electrodeposited polypyrrole (PPy)/para (toluene sulfonic acid)(pTS) free-standing film for lithium secondary battery application, Electrochimica acta 60 (2012) 201-205. ##[33] J. Wu, Z. Mester, J. Pawliszyn, Speciation of organoarsenic compounds by polypyrrole-coated capillary in-tube solid phase microextraction coupled with liquid chromatography/electrospray ionization mass spectrometry, Analytica chimica acta 424(2) (2000) 211-222. ##[34] S. Navale, G. Khuspe, M. Chougule, V. Patil, Camphor sulfonic acid doped PPy/α-Fe2O3 hybrid nanocomposites as NO2 sensors, RSC Advances 4(53) (2014) 27998-28004. ##[35] C. Bu, Q. Tai, Y. Liu, S. Guo, X. Zhao, A transparent and stable polypyrrole counter electrode for dye-sensitized solar cell, Journal of power sources 221 (2013) 78-83. ##[36] E. Armelin, R. Pla, F. Liesa, X. Ramis, J.I. Iribarren, C. Alemán, Corrosion protection with polyaniline and polypyrrole as anticorrosive additives for epoxy paint, Corrosion science 50(3) (2008) 721-728. ##[37] M. Beikmohammadi, L. Fotouhi, A. Ehsani, M. Naseri, Potentiodynamic and electrochemical impedance spectroscopy study of anticorrosive properties of p-type conductive polymer/TiO2 nanoparticles, Solid State Ionics 324 (2018) 138-143. ##[38] Y. Wang, S. Zhang, P. Wang, S. Chen, Z. Lu, W. Li, Electropolymerization and corrosion protection performance of the Nb:TiO2 nanofibers/polyaniline composite coating, Journal of the Taiwan Institute of Chemical Engineers 103 (2019) 190-198. ##[39] I.F. Perepichka, D.F. Perepichka, H. Meng, F. Wudl, Light‐emitting polythiophenes, Advanced Materials 17(19) (2005) 2281-2305. ##[40] L. Ai, Y. Liu, X. Zhang, X. Ouyang, Z. Ge, A facile and template-free method for preparation of polythiophene microspheres and their dispersion for waterborne corrosion protection coatings, Synthetic metals 191 (2014) 41-46. ##[41] P.J. Kinlen, V. Menon, Y. Ding, A mechanistic investigation of polyaniline corrosion protection using the scanning reference electrode technique, Journal of the Electrochemical Society 146(10) (1999) 3690. ##[42] P. Kinlen, Y. Ding, D. Silverman, Corrosion protection of mild steel using sulfonic and phosphonic acid-doped polyanilines, Corrosion 58(6) (2002) 490-497. ##[43] P.P. Deshpande, N.G. Jadhav, V.J. Gelling, D. Sazou, Conducting polymers for corrosion protection: a review, Journal of Coatings Technology and Research 11(4) (2014) 473-494. ##[44] D. Sazou, P.P. Deshpande, Conducting polyaniline nanocomposite-based paints for corrosion protection of steel, Chemical Papers 71(2) (2017) 459-487. ##[45] G. Paliwoda-Porebska, M. Rohwerder, M. Stratmann, U. Rammelt, W. Plieth, Release mechanism of electrodeposited polypyrrole doped with corrosion inhibitor anions, Journal of Solid State Electrochemistry 10(9) (2006) 730-736. ##[46] L. Jiang, J.A. Syed, H. Lu, X. Meng, In-situ electrodeposition of conductive polypyrrole-graphene oxide composite coating for corrosion protection of 304SS bipolar plates, Journal of Alloys and Compounds 770 (2019) 35-47. ##[47] P. Chandrasekhar, Conducting polymers, fundamentals and applications, (1999). ##[48] R. Hasanov, S. Bilgiç, Monolayer and bilayer conducting polymer coatings for corrosion protection of steel in 1 M H2SO4 solution, Progress in Organic Coatings 64(4) (2009) 435-445. ##[49] A. Michalik, M. Rohwerder, Conducting polymers for corrosion protection: a critical view, Zeitschrift für Physikalische Chemie 219(11) (2005) 1547-1559. ##[50] G. Paliwoda-Porebska, M. Stratmann, M. Rohwerder, K. Potje-Kamloth, Y. Lu, A.Z. Pich, H.-J. Adler, On the development of polypyrrole coatings with self-healing properties for iron corrosion protection, Corrosion science 47(12) (2005) 3216-3233. ##[51] Y.I. Kuznetsov, Organic corrosion inhibitors: where are we now? A review. Part IV. Passivation and the role of monoand diphosphonates, International Journal of Corrosion and Scale Inhibition 6(4) (2017) 384-427. ##[52] M.A.A. Ali, Inhibition of mild steel corrosion in cooling systems by low-and non-toxic corrosion inhibitors, The University of Manchester (United Kingdom), 2017. ##[53] B.E. Brycki, I.H. Kowalczyk, A. Szulc, O. Kaczerewska, M. Pakiet, Organic corrosion inhibitors, InTech Open, Corrosion Inhibitors, Principles and Recent Applications2017. ##[54] M. Quraishi, S.K. Shukla, Poly (aniline-formaldehyde): a new and effective corrosion inhibitor for mild steel in hydrochloric acid, Materials Chemistry and Physics 113(2-3) (2009) 685-689. ##[55] R. Karthikaiselvi, S. Subhashini, Study of adsorption properties and inhibition of mild steel corrosion in hydrochloric acid media by water soluble composite poly (vinyl alcohol-o-methoxy aniline), Journal of the Association of Arab Universities for Basic and Applied Sciences 16 (2014) 74-82. ##[56] D.K. Yadav, D. Chauhan, I. Ahamad, M. Quraishi, Electrochemical behavior of steel/acid interface: adsorption and inhibition effect of oligomeric aniline, RSC advances 3(2) (2013) 632-646. ##[57] P. Kinlen, D. Silverman, C. Jeffreys, Corrosion protection using polyanujne coating formulations, Synthetic Metals 85(1-3) (1997) 1327-1332. ##[58] L. Bazli, A. Khavandi, M.A. Boutorabi, M. Karrabi, Correlation between viscoelastic behavior and morphology of nanocomposites based on SR/EPDM blends compatibilized by maleic anhydride, Polymer 113 (2017) 156-166. ##[59] L. Bazli, A. Khavandi, M.A. Boutorabi, M. Karrabi, Morphology and viscoelastic behavior of silicone rubber/EPDM/Cloisite 15A nanocomposites based on Maxwell model, Iranian Polymer Journal 25(11) (2016) 907-918. ##[60] M. Bazli, L. Bazli, R. Rahmani, S. Mansoor, M. Ahmadi, R. Pouriamanesh, Concrete filled FRP–PVC tubular columns used in the construction sector: A review, Journal of Composites and Compounds 2(4) (2020) 155-162. ##[61] S.A. Umoren, M.M. Solomon, Protective polymeric films for industrial substrates: A critical review on past and recent applications with conducting polymers and polymer composites/nanocomposites, Progress in Materials Science 104 (2019) 380-450. ##[62] M.H. Naveen, N.G. Gurudatt, H.B. Noh, Y.B. Shim, Dealloyed AuNi dendrite anchored on a functionalized conducting polymer for improved catalytic oxygen reduction and hydrogen peroxide sensing in living cells, Advanced Functional Materials 26(10) (2016) 1590-1601. ##[63] L. Zhang, W. Du, A. Nautiyal, Z. Liu, X. Zhang, Recent progress on nanostructured conducting polymers and composites: synthesis, application and future aspects, Science China Materials 61(3) (2018) 303-352. ##[64] M. Tomczykowa, M.E. Plonska-Brzezinska, Conducting polymers, hydrogels and their composites: preparation, properties and bioapplications, Polymers 11(2) (2019) 350. ##[65] L. Fu, Q. Qu, R. Holze, V.V. Kondratiev, Y. Wu, Composites of metal oxides and intrinsically conducting polymers as supercapacitor electrode materials: the best of both worlds?, Journal of Materials Chemistry A 7(25) (2019) 14937-14970. ##[66] A. Eftekhari, Nanostructured conductive polymers. 2010, Chichester, West Sussex, UK; Hoboken, NJ: Wiley. xxiii. ##[67] H. Bhandari, S.A. Kumar, S. Dhawan, Conducting polymer nanocomposites for anticorrosive and antistatic applications, Nanocomposites: New Trends and Developments (2012) 73-96. ##[68] C. Cao, M.M. Cheung, Non-uniform rust expansion for chloride-induced pitting corrosion in RC structures, Construction and Building Materials 51 (2014) 75-81. ##[69] M. Bernard, A. Hugot‐Le Goff, S. Joiret, N.N. Dinh, N.N. Toan, Polyaniline layer for iron protection in sulfate medium, Journal of the Electrochemical Society 146(3) (1999) 995. ##[70] D.E. Tallman, G. Spinks, A. Dominis, G.G. Wallace, Electroactive conducting polymers for corrosion control, Journal of Solid State Electrochemistry 6(2) (2002) 73-84. ##[71] D. Tallman, M. Dewald, C. Vang, G. Wallace, G. Bierwagen, Electrodeposition of conducting polymers on active metals by electron transfer mediation, Current Applied Physics 4(2-4) (2004) 137-140. ##[72] D.M. Lenz, M. Delamar, C.A. Ferreira, Improvement of the anticorrosion properties of polypyrrole by zinc phosphate pigment incorporation, Progress in Organic Coatings 58(1) (2007) 64-69. ##[73] D.M. Lenz, M. Delamar, C.A. Ferreira, Application of polypyrrole/TiO2 composite films as corrosion protection of mild steel, Journal of Electroanalytical Chemistry 540 (2003) 35-44. ##[74] T. Schauer, A. Joos, L. Dulog, C. Eisenbach, Protection of iron against corrosion with polyaniline primers, Progress in Organic Coatings 33(1) (1998) 20-27. ##[75] O. Zubillaga, F. Cano, I. Azkarate, I. Molchan, G. Thompson, A. Cabral, P. Morais, Corrosion performance of anodic films containing polyaniline and TiO2 nanoparticles on AA3105 aluminium alloy, Surface and Coatings Technology 202(24) (2008) 5936-5942. ##[76] K. Thompson, Los Alamos National Laboratory Report LA-UR-92-360; DA Wrobleski, BC Benicewicz, KG. Thompson, and CJ Bryan, Polymer Preprints 35 (1994) 265. ##[77] S.P. Sitaram, J.O. Stoffer, T.J. O’Keefe, Application of conducting polymers in corrosion protection, Journal of Coatings Technology 69(866) (1997) 65-69. ##[78] A.J. Heeger, Semiconducting and metallic polymers: the fourth generation of polymeric materials, ACS Publications, 2001. ##[79] M. Qiang, T. Chen, R.-p. Yao, Effect of Preparation Condition of Polyaniline/Monmorillonite Nanocomposite Material on the Anticorrosion Property, MATERIALS PROTECTION-WUHAN- 36(7) (2003) 25-27. ##[80] B. Wessling, Dispersion as the link between basic research and commercial applications of conductive polymers (polyaniline), Synthetic Metals 93(2) (1998) 143-154. ##[81] O.L. Gribkova, A.A. Nekrasov, V.A. Cabanova, T.V. Krivenko, N.V. Nekrasova, S.A. Yakovlev, E.I. Terukov, A.R. Tameev, Water-processable nanocomposite based on polyaniline and 2D molybdenum disulfide for NIR-transparent ambipolar transport layers, Chemical Papers 72(7) (2018) 1741-1752. ##[82] N.N. Taheri, B. Ramezanzadeh, M. Mahdavian, Application of layer-by-layer assembled graphene oxide nanosheets/polyaniline/zinc cations for construction of an effective epoxy coating anti-corrosion system, Journal of Alloys and Compounds 800 (2019) 532-549. ##[83] B. Ramezanzadeh, G. Bahlakeh, M. Ramezanzadeh, Polyaniline-cerium oxide (PAni-CeO2) coated graphene oxide for enhancement of epoxy coating corrosion protection performance on mild steel, Corrosion Science 137 (2018) 111-126. ##[84] A. Baldissera, M. Silveira, C. Beraldo, N. Tocchetto, C. Ferreira, Evaluation of the expandable graphite/polyaniline combination in intumescent coatings, Synthetic Metals 256 (2019) 116141. ##[85] M.J. Mazumder, L. Goni, S. Ali, M. Nazal, Inhibition of mild steel corrosion in hydrochloric acid medium by polymeric inhibitors containing residues of essential amino acid methionine, Iranian Polymer Journal 27(12) (2018) 979-995. ##[86] B. Wessling, From conductive polymers to organic metals, Chemical innovation 31(1) (2001) 34-40. ##[87] J. Stenger-Smith, ‘A General Review of Intrinsically Conducting Polymers as Coatings for Corrosion Protection, Proc. US Navy and Industry Corrosion Technology Information Exchange (2000). ##[88] S. Sathiyanarayanan, S.S. Azim, G. Venkatachari, A new corrosion protection coating with polyaniline–TiO2 composite for steel, Electrochimica Acta 52(5) (2007) 2068-2074. ##[89] S. Radhakrishnan, C.R. Siju, D. Mahanta, S. Patil, G. Madras, Conducting polyaniline–nano-TiO2 composites for smart corrosion resistant coatings, Electrochimica Acta 54(4) (2009) 1249-1254. ##[90] R.C. Patil, S. Radhakrishnan, Conducting polymer based hybrid nano-composites for enhanced corrosion protective coatings, Progress in Organic Coatings 57(4) (2006) 332-336. ##[91] M.G. Hosseini, M. Sabouri, T. Shahrabi, Corrosion protection of mild steel by polypyrrole phosphate composite coating, Progress in Organic Coatings 60(3) (2007) 178-185. ##[92] Y.J. Ren, C.L. Zeng, Effect of conducting composite polypyrrole/polyaniline coatings on the corrosion resistance of type 304 stainless steel for bipolar plates of proton-exchange membrane fuel cells, Journal of Power Sources 182(2) (2008) 524-530. ##[93] R.S. Jadhav, D.G. Hundiwale, P.P. Mahulikar, Synthesis of nano polyaniline and poly-o-anisidine and applications in alkyd paint formulation to enhance the corrosion resistivity of mild steel, Journal of coatings technology and research 7(4) (2010) 449-454. ##[94] K.-C. Chang, M.-H. Hsu, H.-I. Lu, M.-C. Lai, P.-J. Liu, C.-H. Hsu, W.-F. Ji, T.-L. Chuang, Y. Wei, J.-M. Yeh, W.-R. Liu, Room-temperature cured hydrophobic epoxy/graphene composites as corrosion inhibitor for cold-rolled steel, Carbon 66 (2014) 144-153. ##[95] V.S. Sumi, S.R. Arunima, M.J. Deepa, M. Ameen Sha, A.H. Riyas, M.S. Meera, V.S. Saji, S.M.A. Shibli, PANI-Fe2O3 composite for enhancement of active life of alkyd resin coating for corrosion protection of steel, Materials Chemistry and Physics 247 (2020). ##[96] N. Jadhav, S. Kasisomayajula, V. Gelling, Polypyrrole/Metal oxides-based composites/nanocomposites for corrosion protection, Frontiers in Materials 7 (2020) 95. ##[97] M. Sun, Z. Ma, G. Zhu, Y. Zhang, Anticorrosive performance of polyaniline/waterborne epoxy/poly (methylhydrosiloxane) composite coatings, Progress in Organic Coatings 139 (2020) 105462. ##[98] M. Deyab, G. Mele, Stainless steel bipolar plate coated with polyaniline/Zn-Porphyrin composites coatings for proton exchange membrane fuel cell, Scientific Reports 10(1) (2020) 1-8. ##[99] R. Rajkumar, C. Vedhi, Study of the corrosion protection efficiency of polypyrrole/metal oxide nanocomposites as additives in anticorrosion coating, Anti-Corrosion Methods and Materials (2020). ##[100] Z. Chen, W. Yang, B. Xu, Y. Chen, M. Qian, X. Su, Z. Li, X. Yin, Y. Liu, Corrosion protection of carbon steels by electrochemically synthesized V-TiO2/polypyrrole composite coatings in 0.1 M HCl solution, Journal of Alloys and Compounds 771 (2019) 857-868. ##[101] P. Kong, H. Feng, N. Chen, Y. Lu, S. Li, P. Wang, Polyaniline/chitosan as a corrosion inhibitor for mild steel in acidic medium, RSC advances 9(16) (2019) 9211-9217. ##[102] R. Babaei-Sati, J.B. Parsa, M. Vakili-Azghandi, Electrodeposition of polypyrrole/metal oxide nanocomposites for corrosion protection of mild steel—A comparative study, Synthetic Metals 247 (2019) 183-190. ##[103] A. El Jaouhari, A. Chennah, S.B. Jaddi, H.A. Ahsaine, Z. Anfar, Y.T. Alaoui, Y. Naciri, A. Benlhachemi, M. Bazzaoui, Electrosynthesis of zinc phosphate-polypyrrole coatings for improved corrosion resistance of steel, Surfaces and Interfaces 15 (2019) 224-231. ##[104] X. Liu, P. Hou, X. Zhao, X. Ma, B. Hou, The polyaniline-modified TiO2 composites in water-based epoxy coating for corrosion protection of Q235 steel, Journal of Coatings Technology and Research 16(1) (2019) 71-80. ##[105] H.M. Abd El-Lateef, M.M. Khalaf, Novel dispersed Tl2O3-SiO2/polyaniline nanocomposites: in-situ polymerization, characterization and enforcement as a corrosion protective layer for carbon-steel in acidic chloride medium, Colloids and Surfaces A: Physicochemical and Engineering Aspects 573 (2019) 95-111. ##[106] G. Contri, G. Barra, S. Ramoa, C. Merlini, L. Ecco, F. Souza, A. Spinelli, Epoxy coating based on montmorillonite-polypyrrole: Electrical properties and prospective application on corrosion protection of steel, Progress in Organic Coatings 114 (2018) 201-207. ##[107] N. Jadhav, T. Matsuda, V. Gelling, Mica/polypyrrole (doped) composite containing coatings for the corrosion protection of cold rolled steel, Journal of Coatings Technology and Research 15(2) (2018) 363-374. ##[108] A.A. Salem, B.N. Grgur, The influence of the polyaniline initial oxidation states on the corrosion of steel with composite coatings, Progress in Organic Coatings 119 (2018) 138-144. ##[109] L. Jiang, J.A. Syed, Y. Gao, H. Lu, X. Meng, Electrodeposition of Ni(OH)2 reinforced polyaniline coating for corrosion protection of 304 stainless steel, Applied Surface Science 440 (2018) 1011-1021. ##[110] H. Arabzadeh, M. Shahidi, M.M. Foroughi, Electrodeposited polypyrrole coatings on mild steel: Modeling the EIS data with a new equivalent circuit and the influence of scan rate and cycle number on the corrosion protection, Journal of Electroanalytical Chemistry 807 (2017) 162-173. ##[111] M. Ladan, W.J. Basirun, S.N. Kazi, F.A. Rahman, Corrosion protection of AISI 1018 steel using Co-doped TiO2/polypyrrole nanocomposites in 3.5% NaCl solution, Materials Chemistry and Physics 192 (2017) 361-373. ##[112] Q. Yan, C. Li, T. Huang, F. Yang, Electrochemical synthesis of polypyrrole-Al2O3 composite coating on 316 stainless steel for corrosion protection, AIP Conference Proceedings, AIP Publishing LLC, 2017, p. 030005. ##[113] Q. Yan, C. Li, Electrochemical synthesis of polypyrrole-SiO2 composite coating on 316 stainless steel for corrosion protection, Anti-Corrosion Methods and Materials (2017). ##[114] C. Qiu, D. Liu, K. Jin, L. Fang, G. Xie, J. Robertson, Electrochemical functionalization of 316 stainless steel with polyaniline-graphene oxide: Corrosion resistance study, Materials Chemistry and Physics 198 (2017) 90-98. ##[115] S. Lu, H. Yeh, T. Tian, W. Lee, Degradation of magnesium alloys in biological solutions and reduced phenotypic expression of endothelial cell grown on these alloys, 3rd Kuala Lumpur International Conference on Biomedical Engineering 2006, Springer, 2007, pp. 98-101. ##[116] C. Seal, K. Vince, M. Hodgson, Biodegradable surgical implants based on magnesium alloys–A review of current research, IOP conference series: materials science and engineering, IOP Publishing, 2009, p. 012011. ##[117] A.H. Shahbaz, M. Esmaeilian, R. NasrAzadani, K. Gavanji, The effect of MgF2 addition on the mechanical properties of hydroxyapatite synthesized via powder metallurgy, Journal of Composites and Compounds 1(1) (2019) 18-24. ##[118] F. Sharifianjazi, M. Moradi, A. Abouchenari, A.H. Pakseresht, A. Esmaeilkhanian, M. Shokouhimehr, M.S. Asl, Effects of Sr and Mg dopants on biological and mechanical properties of SiO2–CaO–P2O5 bioactive glass, Ceramics International (2020). ##[119] M. Rahmati, K. Raeissi, M.R. Toroghinejad, A. Hakimizad, M. Santamaria, Effect of pulse current mode on microstructure, composition and corrosion performance of the coatings produced by plasma electrolytic oxidation on AZ31 Mg alloy, Coatings 9(10) (2019) 688. ##[120] M. Rahmati, K. Raeissi, M.R. Toroghinejad, A. Hakimizad, M. Santamaria, The multi-effects of K2TiF6 additive on the properties of PEO coatings on AZ31 Mg alloy, Surface and Coatings Technology (2020) 126296. ##[121] X.-N. Gu, Y.-F. Zheng, A review on magnesium alloys as biodegradable materials, Frontiers of Materials Science in China 4(2) (2010) 111-115. ##[122] S. Sathiyanarayanan, S.S. Azim, G. Venkatachari, Corrosion protection of magnesium ZM 21 alloy with polyaniline–TiO2 composite containing coatings, Progress in Organic Coatings 59(4) (2007) 291-296. ##[123] Y. Guo, S. Jia, L. Qiao, Y. Su, R. Gu, G. Li, J. Lian, A multifunctional polypyrrole/zinc oxide composite coating on biodegradable magnesium alloys for orthopedic implants, Colloids Surf B Biointerfaces 194 (2020) 111186. ##[124] Y. Wang, The Electrochemical Corrosion Properties of PANI/Coal Composites on Magnesium Alloys, International Journal of Electrochemical Science (2017) 4044-4055. ##[125] J. Li, Y. He, Y. Sun, X. Zhang, W. Shi, D. Ge, Synthesis of Polypyrrole/V2O5 Composite Film on the Surface of Magnesium Using a Mild Vapor Phase Polymerization (VPP) Method for Corrosion Resistance, Coatings 10(4) (2020). ##[126] A.S. Najibzad, R. Amini, M. Rostami, P. Kardar, M. Fedel, Active corrosion performance of magnesium by silane coatings reinforced with polyaniline/praseodymium, Progress in Organic Coatings 140 (2020) 105504. ##[127] V. Jothi, A.Y. Adesina, A.M. Kumar, M.M. Rahman, J.S.N. Ram, Enhancing the biodegradability and surface protective performance of AZ31 Mg alloy using polypyrrole/gelatin composite coatings with anodized Mg surface, Surface and Coatings Technology 381 (2020) 125139. ##[128] A. Samadi, R. Amini, M. Rostami, P. Kardar, M. Fedel, Preparation of polyaniline-modified praseodymium nanofibers as a novel eco-friendly corrosion inhibitor to protect AZ31 magnesium alloy, Pigment and Resin Technology (2020). ##[129] R. Maurya, A.R. Siddiqui, P.K. Katiyar, K. Balani, Mechanical, tribological and anti-corrosive properties of polyaniline/graphene coated Mg-9Li-7Al-1Sn and Mg-9Li-5Al-3Sn-1Zn alloys, Journal of Materials Science and Technology 35(8) (2019) 1767-1778. ##[130] Y. Li, J. Li, X. Gao, S. Qi, J. Ma, J. Zhu, Synthesis of stabilized dispersion covalently-jointed SiO2@ polyaniline with core-shell structure and anticorrosion performance of its hydrophobic coating for Mg-Li alloy, Applied Surface Science 462 (2018) 362-372. ##[131] X. Gao, X. Jing, Y. Li, J. Zhu, M. Zhang, Synthesis and characterization of phosphorized polyaniline doped with phytic acid and its anticorrosion properties for Mg-Li alloy, Journal of Macromolecular Science, Part A 55(1) (2018) 24-35. ##[132] M. Saremi, S.H. Mortazavi, Effect of polypyrrole coating modified by sodium fluoride and polyethylene glycol on corrosion behaviour of AZ31 magnesium alloy, Micro and Nano Letters 11(12) (2016) 866-869. ##[133] X. Chen, K. Shen, J. Zhang, Preparation and anticorrosion properties of polyaniline‐SiO2‐containing coating on Mg‐Li alloy, Pigment and Resin Technology (2010). ##[134] M. Hosseini, M. Jafari, R. Najjar, Effect of polyaniline–montmorillonite nanocomposite powders addition on corrosion performance of epoxy coatings on Al 5000, Surface and Coatings Technology 206(2-3) (2011) 280-286. ##[135] M. Ghafaripoor, K. Raeissi, M. Santamaria, A. Hakimizad, The corrosion and tribocorrosion resistance of PEO composite coatings containing α-Al2O3 particles on 7075 Al alloy, Surface and Coatings Technology 349 (2018) 470-479. ##[136] I. Tajzad, E. Ghasali, Production methods of CNT-reinforced Al matrix composites: a review, Journal of Composites and Compounds 2(1) (2020) 1-9. ##[137] S. Nasibi, K. Alimohammadi, L. Bazli, S. Eskandarinezhad, A. Mohammadi, N. Sheysi, TZNT alloy for surgical implant applications: A systematic review, Journal of Composites and Compounds 2(3) (2020) 62-68. ##[138] K. Kamaraj, S. Sathiyanarayanan, G. Venkatachari, Electropolymerised polyaniline films on AA 7075 alloy and its corrosion protection performance, Progress in Organic Coatings 64(1) (2009) 67-73. ##[139] E. Akbari, F. Di Franco, P. Ceraolo, K. Raeissi, M. Santamaria, A. Hakimizad, Electrochemically-induced TiO2 incorporation for enhancing corrosion and tribocorrosion resistance of PEO coating on 7075 Al alloy, Corrosion Science 143 (2018) 314-328. ##[140] K. Zhang, H.W. Jang, Q. Van Le, Production methods of ceramic-reinforced Al-Li matrix composites: A review, Journal of Composites and Compounds 2(3) (2020) 77-84. ##[141] E. Asadi, A.F. Chimeh, S. Hosseini, S. Rahimi, B. Sarkhosh, L. Bazli, R. Bashiri, A.H.V. Tahmorsati, A review of clinical applications of graphene quantum dot-based composites, Journal of Composites and Compounds 1(1) (2019) 36-47. ##[142] M. Yan, C.A. Vetter, V.J. Gelling, Corrosion inhibition performance of polypyrrole Al flake composite coatings for Al alloys, Corrosion Science 70 (2013) 37-45. ##[143] M. A. Hussein, Electrodeposition and Corrosion Protection Performance of Polypyrrole Composites on Aluminum, International Journal of Electrochemical Science (2016) 3938-3951. ##[144] M. Hosseini, L. Fotouhi, A. Ehsani, M. Naseri, Enhancement of corrosion resistance of polypyrrole using metal oxide nanoparticles: Potentiodynamic and electrochemical impedance spectroscopy study, J Colloid Interface Sci 505 (2017) 213-219. ##[145] K. Shah, Y. Zhu, G.S. Akundy, J.O. Iroh, O. Popoola, Corrosion and Bonding Behaviors of Intrinsically Conductive Polymers on Aluminum (AI 2024-T3), Key Engineering Materials 197 (2001) 111-120. ##[146] V. Tomaev, K. Levin, T. Stoyanova, A. Syrkov, Synthesis and Study of a Polypyrrole–Aluminum Oxide Nanocomposite Film on an Aluminum Surface, Glass Physics and Chemistry 45(4) (2019) 291-297. ##[147] A.M. Kumar, R.S. Babu, S. Ramakrishna, A.L. de Barros, Electrochemical synthesis and surface protection of polypyrrole-CeO2 nanocomposite coatings on AA2024 alloy, Synthetic Metals 234 (2017) 18-28. ##[148] M. Ates, E. Topkaya, Nanocomposite film formations of polyaniline via TiO2, Ag, and Zn, and their corrosion protection properties, Progress in Organic Coatings 82 (2015) 33-40. ##[149] M. Ates, O. Kalender, E. Topkaya, L. Kamer, Polyaniline and polypyrrole/TiO2 nanocomposite coatings on Al1050: electrosynthesis, characterization and their corrosion protection ability in saltwater media, Iranian Polymer Journal 24(7) (2015) 607-619. ##[150] F. Alvi, N. Aslam, S.F. Shaukat, Corrosion inhibition study of zinc oxide-polyaniline nanocomposite for aluminum and steel, American Journal of Applied Chemistry 3(2) (2015) 57-64. ##[151] M.B. Jensen, M.J. Peterson, N. Jadhav, V.J. Gelling, SECM investigation of corrosion inhibition by tungstate-and vanadate-doped polypyrrole/aluminum flake composite coatings on AA2024-T3, Progress in Organic Coatings 77(12) (2014) 2116-2122. ##[152] G. Gupta, N. Birbilis, A.B. Cook, A.S. Khanna, Polyaniline-lignosulfonate/epoxy coating for corrosion protection of AA2024-T3, Corrosion Science 67 (2013) 256-267. ##[153] N. Jadhav, C.A. Vetter, V.J. Gelling, The effect of polymer morphology on the performance of a corrosion inhibiting polypyrrole/aluminum flake composite pigment, Electrochimica acta 102 (2013) 28-43. ##[154] M. Shabani-Nooshabadi, S.M. Ghoreishi, M. Behpour, Direct electrosynthesis of polyaniline–montmorrilonite nanocomposite coatings on aluminum alloy 3004 and their corrosion protection performance, Corrosion Science 53(9) (2011) 3035-3042. ##[155] K.R. Castagno, V. Dalmoro, R.S. Mauler, D.S. Azambuja, Characterization and corrosion protection properties of polypyrrole/montmorillonite electropolymerized onto aluminium alloy 1100, Journal of polymer research 17(5) (2010) 647-655. ##[156] M. Hosseini, M. Raghibi-Boroujeni, I. Ahadzadeh, R. Najjar, M.S. Dorraji, Effect of polypyrrole–montmorillonite nanocomposites powder addition on corrosion performance of epoxy coatings on Al 5000, Progress in organic coatings 66(3) (2009) 321-327. ##[157] K. Wu, C. Chao, C. Liu, T. Chang, Characterization and corrosion resistance of organically modified silicate–NiZn ferrite/polyaniline hybrid coatings on aluminum alloys, Corrosion science 49(7) (2007) 3001-3014. ##[158] D. Wrobleski, Corrosion resistant coatings from conducting polymers, Meeting of the Division of Polymer Chemistry, 1994, pp. 265-266. ##[159] A. Cascalheira, S. Aeiyach, P. Lacaze, L. Abrantes, Electrochemical synthesis and redox behaviour of polypyrrole coatings on copper in salicylate aqueous solution, Electrochimica acta 48(17) (2003) 2523-2529. ##[160] Y. Meng, J. Yin, T. Jiao, J. Bai, L. Zhang, J. Su, S. Liu, Z. Bai, M. Cao, Q. Peng, Self-assembled copper/cobalt-containing polypyrrole hydrogels for highly efficient ORR electrocatalysts, Journal of Molecular Liquids 298 (2020) 112010. ##[161] W.N. Nyairo, Y.R. Eker, C. Kowenje, I. Akin, H. Bingol, A. Tor, D.M. Ongeri, Efficient adsorption of lead (II) and copper (II) from aqueous phase using oxidized multiwalled carbon nanotubes/polypyrrole composite, Separation Science and Technology 53(10) (2018) 1498-1510. ##[162] M. Menkuer, H. Ozkazanc, Electrodeposition of polypyrrole on copper surfaces in OXA-DBSA mix electrolyte and their corrosion behaviour, Progress in Organic Coatings 130 (2019) 149-157. ##[163] L.A. Cheah, G. Manohara, M.M. Maroto-Valer, S. Garcia, Layered Double Hydroxide (LDH)-Derived Mixed Metal Oxides (MMOs): A Systematic Crystal-Chemical Approach to Investigating the Chemical Composition and its Effect on High Temperature CO2 capture, ChemistrySelect 5(19) (2020) 5587-5594. ##[164] A.J. Rad, Synthesis of copper oxide nanoparticles on activated carbon for pollutant removal in Tartrazine structure, Journal of Composites and Compounds 2(3) (2020) 99-104. ##[165] M. Arefian, M. Hojjati, I. Tajzad, A. Mokhtarzade, M. Mazhar, A. Jamavari, A review of Polyvinyl alcohol/Carboxiy methyl cellulose (PVA/CMC) composites for various applications, Journal of Composites and Compounds 2(3) (2020) 69-76. ##[166] A. Abuchenari, M. Moradi, The Effect of Cu-substitution on the microstructure and magnetic properties of Fe-15% Ni alloy prepared by mechanical alloying, Journal of Composites and Compounds 1(1) (2019) 11-17. ##[167] A. Moghanian, A. Ghorbanoghli, M. Kazem‐Rostami, A. Pazhouheshgar, E. Salari, M. Saghafi Yazdi, T. Alimardani, H. Jahani, F. Sharifian Jazi, M. Tahriri, Novel antibacterial Cu/Mg‐substituted 58S‐bioglass: Synthesis, characterization and investigation of in vitro bioactivity, International Journal of Applied Glass Science (2019). ##[168] G. Kilincceker, B. Yazici, A. Yilmaz, M. Erbil, Effect of phosphate ions on electrochemical behaviour of copper in sulphate solutions, British Corrosion Journal 37(1) (2002) 23-30. ##[169] B. Tan, S. Zhang, Y. Qiang, L. Guo, L. Feng, C. Liao, Y. Xu, S. Chen, A combined experimental and theoretical study of the inhibition effect of three disulfide-based flavouring agents for copper corrosion in 0.5 M sulfuric acid, Journal of colloid and interface science 526 (2018) 268-280. ##[170] H. Alhumade, A. Abdala, A. Yu, A. Elkamel, L. Simon, Corrosion inhibition of copper in sodium chloride solution using polyetherimide/graphene composites, The Canadian Journal of Chemical Engineering 94(5) (2016) 896-904. ##[171] A. Asan, M. Kabasakaloglu, M. Işıklan, Z. Kılıç, Corrosion inhibition of brass in presence of terdentate ligands in chloride solution, Corrosion Science 47(6) (2005) 1534-1544. ##[172] B.M. Thethwayo, A.M. Garbers-Craig, Laboratory scale investigation into the corrosion of copper in a sulphur-containing environment, Corrosion science 53(10) (2011) 3068-3074. ##[173] J. Chen, Z. Qin, D. Shoesmith, Long-term corrosion of copper in a dilute anaerobic sulfide solution, Electrochimica acta 56(23) (2011) 7854-7861. ##[174] A.M. Fenelon, C.B. Breslin, The electrochemical synthesis of polypyrrole at a copper electrode: corrosion protection properties, Electrochimica Acta 47(28) (2002) 4467-4476. ##[175] T. Tüken, B. Yazıcı, M. Erbil, Polypyrrole/polythiophene coating for copper protection, Progress in organic coatings 53(1) (2005) 38-45. ##[176] A. Guenbour, A. Kacemi, A. Benbachir, Corrosion protection of copper by polyaminophenol films, Progress in organic coatings 39(2-4) (2000) 151-155. ##[177] M. Redondo, C.B. Breslin, Polypyrrole electrodeposited on copper from an aqueous phosphate solution: Corrosion protection properties, Corrosion science 49(4) (2007) 1765-1776. ##[178] W. Prissanaroon, N. Brack, P. Pigram, J. Liesegang, Electropolymerisation of pyrrole on copper in aqueous media, Synthetic metals 142(1-3) (2004) 25-34. ##[179] M. Bazzaoui, J. Martins, E. Bazzaoui, T. Reis, L. Martins, Pyrrole electropolymerization on copper and brass in a single-step process from aqueous solution, Journal of applied electrochemistry 34(8) (2004) 815-822. ##[180] L.M. Dos Santos, J. Lacroix, K. Chane-Ching, A. Adenier, L. Abrantes, P. Lacaze, Electrochemical synthesis of polypyrrole films on copper electrodes in acidic and neutral aqueous media, Journal of Electroanalytical Chemistry 587(1) (2006) 67-78. ##[181] P. Herrasti, A. Del Rio, J. Recio, Electrodeposition of homogeneous and adherent polypyrrole on copper for corrosion protection, Electrochimica acta 52(23) (2007) 6496-6501. ##[182] M.M. Gvozdenović, B.Z. Jugović, J.S. Stevanović, B. Grgur, T.L. Trišović, Z.S. Jugović, Electrochemical synthesis and corrosion behavior of polyaniline-benzoate coating on copper, Synthetic Metals 161(13-14) (2011) 1313-1318. ##[183] T.J. Pan, X.W. Zuo, T. Wang, J. Hu, Z.D. Chen, Y.J. Ren, Electrodeposited conductive polypyrrole/polyaniline composite film for the corrosion protection of copper bipolar plates in proton exchange membrane fuel cells, Journal of Power Sources 302 (2016) 180-188. ##[184] İ. Çakmakcı, B. Duran, G. Bereket, Influence of electrochemically prepared poly(pyrrole-co-N-methyl pyrrole) and poly(pyrrole)/poly(N-methyl pyrrole) composites on corrosion behavior of copper in acidic medium, Progress in Organic Coatings 76(1) (2013) 70-77. ##[185] F. Branzoi, V. Branzoi, Z. Pahom, Monolayer and bilayer conducting polymer coatings for corrosion protection of copper in 0.5 M H2SO4 solutions, Rev. Roum. Chim 58(1) (2013) 49-58. ##[186] B.P. Singh, B.K. Jena, S. Bhattacharjee, L. Besra, Development of oxidation and corrosion resistance hydrophobic graphene oxide-polymer composite coating on copper, Surface and Coatings Technology 232 (2013) 475-481. ##[187] H. Kim, H. Lee, H.-R. Lim, H.-B. Cho, Y.-H. Choa, Electrically conductive and anti-corrosive coating on copper foil assisted by polymer-nanocomposites embedded with graphene, Applied Surface Science 476 (2019) 123-127. ##[188] B.P. Singh, S. Nayak, K.K. Nanda, B.K. Jena, S. Bhattacharjee, L. Besra, The production of a corrosion resistant graphene reinforced composite coating on copper by electrophoretic deposition, Carbon 61 (2013) 47-56. ##[189] S. Wan, C.-H. Miao, R.-M. Wang, Z.-F. Zhang, Z.-H. Dong, Enhanced corrosion resistance of copper by synergetic effects of silica and BTA codoped in polypyrrole film, Progress in Organic Coatings 129 (2019) 187-198. ##[190] Y. Jafari, S. Ghoreishi, M. Shabani-Nooshabadi, Polyaniline/graphene nanocomposite coatings on copper: electropolymerization, characterization, and evaluation of corrosion protection performance, Synthetic Metals 217 (2016) 220-230. ##[191] M. Shabani-Nooshabadi, F. Karimian-Taheri, Electrosynthesis of a polyaniline/zeolite nanocomposite coating on copper in a three-step process and the effect of current density on its corrosion protection performance, RSC advances 5(117) (2015) 96601-96610. ##[192] A. Davoodi, S. Honarbakhsh, G.A. Farzi, Evaluation of corrosion resistance of polypyrrole/functionalized multi-walled carbon nanotubes composite coatings on 60Cu–40Zn brass alloy, Progress in Organic Coatings 88 (2015) 106-115. ##[193] S. Dhibar, S. Sahoo, C. Das, R. Singh, Investigations on copper chloride doped polyaniline composites as efficient electrode materials for supercapacitor applications, Journal of Materials Science: Materials in Electronics 24(2) (2013) 576-585.##